Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone pressure hose REDSIL has versatile applications over a wide temperature range. It is used for both hot air and, for example, in cooling systems. Designed for liquids and gases, it is employed in various industrial sectors, including the chemical industry. Inner layer: transparent silicone. Reinforcement: olpot PET (polyester). Outer layer: red silicone. Hardness: 70° ±5° Shore (A). Operating temperature: from -50°C to +200°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone elbow 45° reinforced with polyester is intended for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, a version with a fluorosilicone inner layer is recommended. Arm length: 100 mm (also available with arm lengths of 152, 250 mm). Pressure safety factor: 3:1. The hose meets SAE J20R1 standards. Hardness (standard version) approx. 65° Shore (A), density approx. 1.26 g/cm³. Color of the outer layer: blue. Material: silicone rubber. Reinforcement: polyester inserts. Working pressure: from 1.5 bar to 8.33 bar (depending on hose diameter). Operating temperature: from -50°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsKnown and proven for years, a lightweight and soft natural rubber hose in light brown color. Easy to install due to its softness (hardness 40° Shore – A), flexibility, and elasticity (maximum elongation 500%). It has properties similar to latex. Abrasion-resistant, with good resistance to acids and bases. Used for liquids and gases, for various industrial applications such as dispensing and dosing soaps and detergents, alcoholic and dairy products, laboratories. Sterilization with steam for 30 minutes (1 bar, 141°C) or ethylene oxide. Full hose roll length is 50 m (from inner diameter 7 mm - 25 m). The specified working pressure is determined relative to the burst pressure with a safety factor of 1:5. Material: natural rubber (NR). Operating temperature: from -35°C to +70°C (120°C for moist heat). Brittleness temperature: -40°C. Hardness: 40° Shore (A). Density: 0.98 g/cm³. Note: Product packaged in the Clean Zone of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose designed for the transmission of compressed air, for compressors, hammers, drills, and other pneumatic tools. Due to its low weight, flexibility, robust construction, and high working pressure, it has been accepted and successfully used for many years in construction (particularly in demolition companies), industry, and mining. Extremely durable and long-lasting due to high-quality materials and construction. Reinforced with a circumferentially woven polyester braid completely bonded and surrounded by rubber in the original hot extrusion process of the rubber mixture through the braid. UV resistant. The inner layer is smooth, ensuring minimal flow loss. The yellow, ribbed outer surface is resistant to abrasion, oils, and ozone, and is highly visible on construction sites. Flat when at rest, facilitating handling and storage. Resistant to longitudinal loads. Most commonly used with air couplings (spacing 42 or 41 mm) mounted with cast iron clamps (ordered separately). Also available in black. Use for high-pressure air should always be preceded by a risk analysis in the event of accidental disconnection or rupture of the hose and potential application of safeguards. Maximum working pressure established according to a safety factor of 4:1 approved by the manufacturer for air. Exceeding 1/3 of the specified breaking force is not recommended. Standard roll length: 200 m. Hose material: yellow NBR/PVC mixture with UV-resistant barrier, embedded in the polyester braid during the hose extrusion process. Working pressure: from 12.5 bar to 25 bar - depending on the hose diameter and temperature. Operating temperature: from -30°C to +75°C (temporarily up to +80°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible metal hose made of stainless steel designed for the discharge of gases with liquid particles, smoke, vapors, transport of dry bulk materials (ashes, dust, grain, granules), and as a protective hose. Installed in exhaust systems of engine exhausts as a component that absorbs vibrations, noise, and reduces the effects of thermal expansion. The standard version maintains its shape. The letter F at the end of the index indicates the FLOPPY version, which does not maintain its shape. Material: AISI 304 steel. Operating temperature: up to +650°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible, popular general-purpose PVC hose. Used for air, water, and light chemicals in industry, agriculture, horticulture, and for domestic use. Roll length: 60 meters. Inner layer: transparent PVC. Reinforcement: polyester braid. Outer layer: transparent PVC. Working pressure at 20°C: from 10 bar to 15 bar - depending on the hose diameter and decreases with increasing temperature. Operating temperature: from -5°C to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone reducer connector reinforced with polyester is intended for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, the version with a fluorosilicone inner layer is recommended. Standard length: 102 mm. Pressure safety factor: 3:1. The hose meets SAE J20R1 standards. Hardness (standard version) approx. 65° Shore (A), density approx. 1.26 g/cm3. Color of the outer layer: blue. Material: silicone rubber. Reinforcement: polyester spacers. Working pressure: from 1 bar to 7.33 bar (depending on hose diameter). Operating temperature: from -50°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal, highly flexible, unreinforced hose designed for non-pressurized (or very low pressure) transfer of water, beer, wine, alcohols, juices, and beverages. The absence of phthalates in the hose material makes it suitable for the transfer of milk and its derivatives, as well as alcohols with a volumetric concentration of up to 50% and temperatures up to +40°C. Not recommended for oils and fatty food substances. Also used for liquids in general industrial applications, for light chemicals (acids, bases), for solid substances (powders), and as protection for pipes, conduits, hoses, etc. For the hose, the stated pressure value is an indicative value of the recommended working pressure, assumed for a typical PVC hose, with a safety factor of 5:1. The use of the hose for a specific working pressure should be preceded by testing under working conditions. Standards and requirements: Food industry, food contact: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulated fluids A, B, C, and D1), 2023/2006/EC (GMP). Hose material: transparent PVC. Working pressure: low, up to several bar, depending on temperature. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong and flexible rubber pressure hose, intended for water, paints, light chemicals, and air. Can be used for water-based epoxy and polyurethane dispersion paints. Not suitable for cellulose paints, chlorinated rubber, and others containing aromatic solvents such as toluene, xylene, or gasoline, as well as for oils, fuels, and aromatic hydrocarbons. For chemical applications, we recommend contacting Tubes International. Conductive inner and outer layer (R<105 Ω/m), outer layer resistant to ozone, aging, and weather conditions. Inner layer: black EPDM rubber. Reinforcement: polyester braid (DN6 ÷ DN25), 2 polyester braids (DN32 ÷ DN38). Outer layer: black EPDM rubber. Working pressure: 20 bar. Operating temperature: from -40°C to +95°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible metal hose made of carbon steel designed for the discharge of gases with liquid particles, fumes, vapors, transport of dry bulk materials (ashes, dust, grain, granules), and as a protective hose. Installed in exhaust systems of engine exhausts as a component that absorbs vibrations, noise, and reduces the effects of thermal expansion. The standard version maintains its shape. The letter "F" at the end of the index indicates the FLOPPY version, which does not maintain its shape. Material: galvanized carbon steel. Operating temperature: up to +500°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, very soft, extremely flexible and elastic hose characterized by high resistance to bending and lack of shape memory. Designed for air, water, and light chemicals. Maintains flexibility at low temperatures. Outer layer resistant to abrasion. Resistant to UV radiation and weather conditions. Hose material free from cadmium and silicone, complies with RoHS requirements. Roll length: 100 m. Inner layer: yellow (Y) or blue (BL) PVC. Reinforcement: polyester braid. Outer layer: yellow (Y) or blue (BL) PVC. Working pressure at 20°C: 20 bar. As the operating temperature increases, the working pressure value of the hose decreases. Operating temperature: from -25°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong and durable high-quality flat hose designed for trouble-free and maintenance-free operation in harsh field conditions. Used particularly for water, sludge, sewage, and other liquids. Made from hydrolysis and microbe-resistant polyurethane - polyether. Reinforced with a circumferentially woven polyester braid bonded and surrounded by polyurethane in the original hot thermoplastic polyurethane extrusion production process through braiding. The hose has high tensile strength, minimal elongation under pressure, and no tendency to kink or twist. Excellent abrasion and puncture resistance allows operation in heavy, uneven terrain and minimizes wear on the water-loaded hose during possible pressure pulsations. Due to its strength and durability combined with ease of handling (rewinding - unwinding), it is used in permanent and temporary high-pressure and high-efficiency water systems in the mining, energy, agriculture, and firefighting industries. Resistant to a wide range of chemicals, microbes, fungi, hydrolysis, weather conditions, UV, and ozone. To confirm the resistance and application conditions of the hose, contact Tubes International. Maximum working pressure for temporary use established according to a safety factor of 2:1 approved by the manufacturer (only for water and safe, non-flammable liquids). For maximum longevity, it is not recommended to exceed 1/3 of the bursting pressure. Standard roll length: 200 m. Hose material: black polyurethane - polyether (PU). Working pressure: from 15 bar to 21 bar - depending on the hose diameter and temperature. Operating temperature: from -50°C to +75°C (water).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone hose reinforced with meta-aramid is intended for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, a version made of fluorocarbon rubber is recommended. Standard length: 1000 mm (also available in lengths of 2000 mm and 3000 mm). Pressure safety factor: 3:1. The hose meets SAE J20R1 standards. Outer layer color: blue. Material: silicone rubber. Reinforcement: meta-aramid layers. Working pressure: from 1 bar to 8.75 bar (depending on hose diameter). Operating temperature: from -50°C to +230°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone anti-vibration connector with one notch reinforced with polyester is intended for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, the version with fluorocarbon rubber is recommended. Pressure safety factor: 3:1. Complies with SAE J2006 R3 standard. Hardness (standard version) approx. 65° Shore (A), density approx. 1.26 g/cm³. Color of the outer layer: blue. Material: silicone rubber. Reinforcement: polyester spacers. Operating temperature: from -50°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal flexible high-quality polyurethane hose produced in the United Kingdom. Designed for water, air, oils, fuels, lubricants, chemicals, and granules. As a non-reinforced hose, it is suitable for very low pressure up to several bar and as a protective hose. The crystal-clear wall allows for excellent observation of the medium. The smooth inner surface facilitates flow and cleaning. Stronger than similar PVC hoses, better at maintaining its shape, well resistant to kinking, flexible at low temperatures. Made from polyurethane – polyether, resistant to hydrolysis and abrasion. Contains no cadmium, silicone, plasticizers, or halogen compounds. According to EU regulations, use for food products is possible after conducting the required migration tests using appropriate model liquids simulating the specific type of food (the material used for hose production complies with FDA requirements 21 CFR 175.105, 177.1680, 177.2600, and WRAS for water at 23°C). Hose material: soft, transparent polyurethane (polyether) free of phthalates. Operating temperature: from -30°C to +70°C (temporarily up to +100°C). Brittleness temperature: -70°C. Recommended working pressure value: from 2.5 bar to 4.8 bar - depending on the hose diameter. As the operating temperature increases, the working pressure value of the hose decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone reducing elbow 90° reinforced with polyester is intended for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, a version with a fluorosilicone inner layer is recommended. Standard arm length: 102 mm. Pressure safety factor: 3:1. The hose meets SAE J20R1 standards. Hardness (standard version) approx. 65° Shore (A), density approx. 1.26 g/cm³. Color of the outer layer: blue. Material: silicone rubber. Reinforcement: polyester inserts. Working pressure: from 1 bar to 7.33 bar (depending on hose diameter). Operating temperature: from -50°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPneumatic extension - ready air hose made of SOFT PLUS. Finished with a brass socket and Eurostandard DN7.2 plug compatible with commonly available quick couplings on the market. Equipped with bend restrictors. Ideal solution for connecting pneumatic tools, easy to operate, vibration-damping. Ensures a high standard of operator work. Available lengths: 10 or 15 m. Inner layer: yellow (Y) or blue (BL) PVC. Reinforcement: polyester braid. Outer layer: yellow (Y) or blue (BL) PVC. Working pressure at 20°C: 20 bar and decreases with increasing working temperature. Operating temperature: from -25°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong and flexible, classic rubber hose designed for compressed air (also oiled), water, and non-aggressive chemical liquids in industry and agriculture. Outer layer resistant to abrasion, aging, ozone, and weather conditions. Inner layer: black synthetic rubber. Reinforcement: synthetic braid. Outer layer: black synthetic rubber. Working pressure: 20 bar. Operating temperature: from -25°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMultifunctional PVC hose, soft, flexible, and elastic. Designed for water, air, and light chemicals. Often used for color differentiation of individual installation lines. Available in black upon special request. Can be used (at temperatures up to 40°C) for liquid and semi-liquid food products such as juices, beverages, beer, wine, alcohols with a concentration of up to 50%, milk, and its derivatives. Not recommended for oils and fatty food substances. The TCN COLOR hose complies with European requirements 1935/2004/EC, 10/2011/EU (simulants A, B, C, and D1), 2023/2006/EC (GMP). Suitable for temporary contact with food during the transfer of food substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International). Inner layer: transparent PVC. Reinforcement: polyester braid. Outer layer: red (R) or blue (BL) PVC. Working pressure at 20°C: from 16 bar to 22 bar - depending on the hose diameter. As the operating temperature increases, the working pressure value of the hose decreases. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, abrasion-resistant pressure hose designed for the transmission of drinking water in large quantities under high working pressure. Flat in a resting state, which facilitates handling and storage. With minimal elongation under pressure and no tendency to kink or twist. Reinforced with a circumferentially woven polyester braid, completely bonded and surrounded by thermoplastic polyurethane in the original hot extrusion production process through braiding. Meets requirements for the transmission of cold drinking water: PZH (no. B.BK.60110.0171.2022, valid until 01.04.2025), KTW-DVGW, WRAS(BS6920), and NSF61. Intended for permanent, temporary, and emergency drinking water supply installations. Used for delivering water to ships, in military field installations, humanitarian actions, mass event services, festivals, etc. Available in other diameters up to 305 mm upon special request. Maximum working pressure for temporary use established according to a safety factor of 2:1 approved by the manufacturer (only for water and safe, non-flammable liquids). To maximize lifespan, it is not recommended to exceed 1/3 of the bursting pressure and the specified breaking force. Standard roll length: 200 m. Hose material: blue polyurethane - polyether (PU) embedded in the braid (textile spacer) in the hose extrusion process. Working pressure: from 18 bar to 25 bar - depending on the hose diameter and temperature. Operating temperature: from -50°C to +75°C (for clean water).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, soft, and flexible, easy to operate food-grade suction hose designed for the transfer of food substances requiring the use of odorless and tasteless rubber. Free from phthalates and bisphenol A. Suitable for milk and its derivatives, as well as wine, beer, and fruit juices. Not recommended for oils and fatty food substances. The outer layer of the hose is resistant to abrasion and weather conditions. Standards and requirements: Food industry, food contact 1935/2004/EC and 2023/2006/EC (GMP), D.M. 21/03/73, FDA 21 CFR 177.2600, BfR XXI cat. 2. Inner layer: white natural rubber (NR). Reinforcement: synthetic cord. Outer layer: blue EPDM rubber. Working pressure: 6 bar. Operating temperature: from -25°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality suction hose designed for the transfer of wine, beer, fruit juices, etc., and food substances that do not contain fats, requiring the use of odorless and tasteless rubber. Free from phthalates and bisphenol A. Designed for high-class wines and spirits, for use in breweries and distilleries. Widely used in the spirits industry for the transfer of strong alcohols with concentrations up to 96%. Features copper wires ensuring electrical continuity between the hose ends, which increases the safety of transferring high-proof, flammable alcohol (ensure contact of the wire with the end during installation). The outer layer is resistant to abrasion, aging, and weather conditions. Standards and requirements: Food industry, food contact 1935/2004/EC, 2023/2006/EC (GMP). Inner layer compliant with FDA 21 CFR 177.2600, BfR XXI cat.2, D.M. 21/03/73. Inner layer: white butyl rubber (IIR). Reinforcement: synthetic cord. Outer layer: red butyl rubber (IIR). Working pressure: 10 bar. Operating temperature: from -40°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible five-layer hose for compressed air. Lightweight, very flexible even at low temperatures, resistant to elongation. Antistatic (R <106 Ω/m, EN ISO 8031), resistant to elevated ambient temperatures, suitable for disinfection. Specifically designed for breathing apparatus in accordance with EN 14593 and EN 14594 standards. Used in the paint industry, petrochemical industry, construction, and nuclear energy. Available on special order in DN6 and DN10 in green color. Inner layer: black, antistatic PVC. Reinforcement: polyester braid. Outer layer: blue PVC. Working pressure: 15 bar (6 bar at 70°C). Operating temperature: from -20°C to +70°C (temporarily up to +80°C), working pressure dependent on temperature.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery flexible hose designed for the transfer of food, pharmaceutical, and cosmetic substances: water, fruit juices, beer, wine, vinegar, alcohols up to 96% concentration, milk and its derivatives, creams, soaps, aromatic substances, pigments, and others. Resistant to fats and oils in standard usage conditions. Good chemical resistance to light chemicals – solutions of acids and bases. Extruded, completely smooth inner and outer layers of the hose facilitate flow and cleaning. The hose material is non-vulcanized, clean (contains no vulcanization additives), resistant to hydrolysis, does not promote bacterial growth, has low porosity and low permeability. Completely neutral in taste and odor, does not alter the organoleptic properties of the medium. Resistant to aging, weather conditions, and UV radiation. Hose cleaning, disinfection, or sterilization should be carried out strictly according to the recommendations provided in the catalog sheet below. Cleaning by SIP method is not recommended as it significantly shortens the service life. Use for high-proof alcohol (its vapors or other flammable substances) requires consideration of hazards related to static electricity. Standards and requirements: 1) Food industry, contact with food: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulants A, B, C, D1, D2), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 "e". 2) Pharmaceutical industry USP CLASS VI. Hose material: transparent TPE-S. Reinforcement: polyester braid. Working pressure: from 7 bar to 12 bar, depending on the hose diameter. Operating temperature: -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight and flexible, popular general-purpose PVC hose. Used for water, air, light chemicals in agriculture, horticulture, industry, and for domestic use. Inner layer: transparent PVC. Reinforcement: polyester braid. Outer layer: green transparent PVC. Working pressure at 20°C: from 10 bar to 17 bar - depending on the hose diameter. Operating temperature: from -5°C to +60°C. As the operating temperature increases, the working pressure value of the hose decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal, highly flexible, unreinforced hose produced in the United Kingdom. Designed for non-pressurized (or very low-pressure) transmission of air, water, and liquids in general industrial applications, for light chemicals (e.g., diluted acids and bases), in laboratory applications, for level indicators, and as protection for pipes, conduits, hoses, etc. The hose material is free from phthalates, silicone, and cadmium, compliant with REACH, RoHS, and WEEE regulations. According to EU regulations, use for food products is possible after conducting the required migration tests using appropriate model fluids simulating the specific type of food (the material used for hose production complies with the requirements of 10/2011/EU and FDA 21). The hose material is self-extinguishing according to UL94-V2 and UL94-HB (at a thickness of 3 mm). The stated working pressure is an indicative value of the recommended working pressure with a safety factor of 5:1. Hose material: transparent PVC. Operating temperature: from -20°C to +55°C (temporarily up to +65°C, working pressure dependent on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, very flexible pressure hose designed for the transfer of water, juices, beverages, and other food products at temperatures up to +40°C. The absence of phthalates in the hose material makes it suitable for the transfer of milk and its derivatives, as well as alcohols with concentrations up to 50% and temperatures up to +40°C. Not recommended for oils and fatty food substances. Also widely used in industry and laboratories for compressed air, gases, and light chemicals. The reinforcement with a spiral braid ensures high pressure resistance and low deformation of the hose under pressure, even with pressure pulsations (within the working pressure range). Standards and requirements: Food industry, food contact: compliant with European regulations 1935/2004/EC and 10/2011/EU (simulant fluids A, B, C, and D1), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: polyester braid. Working pressure: from 9 bar to 27 bar, depending on the hose diameter. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose designed for the transfer of liquid food substances, drinking water, and chemicals. The inner layer of the hose is made of high-density polyethylene (HDPE) of food quality. This material meets high requirements for drinking water regarding the absence of migration of components to the water remaining in the hose and the lack of tendency to form biofilm (microbiological test). At the same time, it meets food contact requirements for liquid food substances and has very high chemical resistance (acids, bases, hydrocarbons, solvents). Therefore, the hose can be used for: 1) drinking water installations (Germany: KTW, DVGW); 2) liquid food substances (water, fruit juices, alcohols, milk and its products, fats and oils); 3) chemicals in a wide range (selection in contact with Tubes International Sp. z o.o.). Thanks to the multi-layer construction of the hose, where the intermediate and outer layers are made of soft polyethylene, the hose is very flexible. For installation, fittings with a spigot ("tail" for the hose) without sharp notches that could cut the inner layer of HDPE upon tightening should be used. Standards and requirements: 1) Food industry, food contact - compliant with European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B, C, D1, D2), 2023/2006/EC (GMP). 2) Approval for drinking water KTW-A (certificate from the German Institute of Hygiene) and DVGW W270 (microbiological material test). Inner layer: HDPE polyethylene. Intermediate layers: natural soft polyethylene PE. Reinforcement: polyester braid. Outer layer: blue soft polyethylene PE. Working pressure: 16 bar, dependent on temperature. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDurable pressure hose designed for the transport of industrial water, sewage, sludges, etc. Inner layer: black smooth SBR rubber. Reinforcement: high-strength synthetic cord. Outer layer: black SBR rubber. Working pressure: 10 bar. Operating temperature: from -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong pressure hose with thick walls, designed for the transfer of food substances requiring the use of odorless and tasteless rubber. Free from phthalates and bisphenol A. The hose is specially designed for the transfer of oils and fats. Widely used in the oil and fat industry. The outer layer is fully resistant to grease and aging. Standards and requirements: Food industry, food contact 1935/2004/EC and 2023/2006/EC (GMP). Inner layer compliant with FDA 21 CFR 177.2600, D.M. 21/03/73. Inner layer: white NBR/PVC rubber. Reinforcement: two layers of synthetic cord. Outer layer: blue CR rubber. Working pressure: 10 bar. Operating temperature: -15°C to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight and flexible flat-folded suction hose for water for hydrants and fire pumps, without fittings. The hydrant hose complies with the EN 14540 standard and is used in internal hydrants according to EN-671-2. The hose for pumps is used for fire, rescue, and forestry motor pumps. In addition to fire-fighting functions, it is widely used in industry, construction, agriculture, and mining. It can be used for the transmission of water, seawater, industrial water, and solutions of certain chemical substances. The inner layer is smooth, resistant to mold and rot. The outer layer (braid) is of high strength, resistant to weather conditions and abrasion. Also available in a yellow luminescent version (DN52, DN75, 20m, for pumps). Certifications (Poland): Hoses comply with the technical conditions of the MSWiA Regulation of April 27, 2010. Inner layer: PVC insert (PU for DN110). Reinforcement: polyester braid. Working pressure: from 12 bar to 15 bar - depending on the hose diameter. Operating temperature: from -30°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible pressure hose designed for the transmission of drinking water, cold (+23°C) and hot (+60°C). Its white, mirror-like inner surface prevents biofilm formation on the walls and is easy to maintain. It does not negatively affect health properties, is free from phthalates, ADI (animal-derived contaminants), and other hazardous substances subject to restrictions according to REACH. It does not cause changes in the organoleptic properties of water even at elevated temperatures. The outer layer is resistant to abrasion, ozone, and weather conditions. Cleaning: steam at +120°C for a maximum of 30 minutes (in an open system), other (CIP) in consultation with Tubes International. Standards and requirements: 1) General: EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) Approval for drinking water: PZH B.BK.60110.0823.2022 (valid until 10.08.2025), UBA guideline, KTW, DVGW W270, D.M.174. 3) Food industry, contact with food: EC 1935/2004, EC 2023/2006 (GMP); EC 10/2011 (inner layer). Inner layer: smooth with a mirror-like surface technopolymer. Reinforcement: synthetic braid. Outer layer: blue technopolymer. Working pressure: from 10 bar to 20 bar, depending on the hose diameter. Operating temperature: from -30°C to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible water delivery hose for general use manufactured in France. Multi-layer construction and strong woven reinforcement ensure high flexibility and prevent twisting, facilitating manual handling of the hose. Very good resistance to repeated bending, crushing, and stretching. Low deformation under pressure. Smooth inner layer ensures good flow. Outer layer resistant to abrasion, aging, and UV radiation. Due to its design, particularly recommended for irrigation systems in agriculture, horticulture, as well as in construction and roadworks. Inner layer: two-layer, black PVC. Reinforcement: strong woven polyester braid. Outer layer: two-layer yellow PVC. Working pressure: from 8 bar to 10 bar - depending on hose diameter and temperature. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight and flexible flat-folded suction hose for water for fire pumps, without fittings. Used for fire, rescue, and forestry pumps. In addition to fire-fighting functions, widely used for water transfer in industry, construction, agriculture, and mining. The inner layer is smooth, resistant to mold and rot. The outer layer (braid) has high strength, with a polyurethane coating that does not retain dirt, increasing resistance to abrasion and contact with flames. Certifications: hoses compliant with the technical conditions of the MSWiA Regulation of April 27, 2010. Inner layer: smooth polyurethane. Reinforcement: polyester braid. Outer layer: red polyurethane coating. Working pressure: from 12 bar to 15 bar - depending on the hose diameter. Operating temperature: from -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight, flat (at rest) industrial PVC suction hose. Thanks to the appropriately selected textile reinforcement with a polyester liner, it has good resistance to elongation. Designed for pressure transmission of water and other liquids. Widely used in agriculture, construction, shipbuilding, mining, etc. Standard roll length: 50 m or 100 m. Inner layer: black PVC. Reinforcement: polyester liner. Outer layer: blue PVC. Working pressure: from 2.5 bar to 8.5 bar - depending on the hose diameter and temperature. Operating temperature: from -5°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose intended for the transmission of cold drinking water (+23°C - approvals KTW, DVGW - Germany, WRAS - United Kingdom, D.M.174 - Italy) in industry and applications such as households, campgrounds, etc. The inner layer material is of food-grade quality, odorless and tasteless, ensuring the preservation of unchanged organoleptic properties of water. Free from phthalates. The outer layer is resistant to weather conditions. Standards and requirements: 1) General: EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) Approval for drinking water: UBA guideline, KTW, DVGW W270, D.M.174, WRAS according to BS 6920. 3) Food industry, contact with food: 1935/2004/EC, 2023/2006/EC (GMP); 21CFR 177.1520, BfR III, 10/2011/EU (inner layer). Inner layer: white plastomer. Reinforcement: synthetic braid. Outer layer: blue synthetic rubber. Working pressure: 20 bar. Operating temperature: -30°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose designed for compressed air. Recommended for pneumatic tools, compressors, hose reels, etc. Inner layer: black PVC. Reinforcement: polyester braid. Outer layer: beige PVC. Working pressure: 20 bar. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal rubber hose intended for low-pressure applications: hydraulic oil, pneumatic and water installations. Widely used for cooling injection molds. Inner layer made of synthetic rubber resistant to high temperatures (mineral oil), outer layer resistant to weather conditions, abrasion, and oil. Not recommended for flammable hydraulic fluids based on phosphate esters. Safety factor 3:1. The hose is designed to work with self-clamping PUSH-ON type fittings. Inner layer: black synthetic rubber. Reinforcement: synthetic braid. Outer layer: blue or red synthetic rubber. Working pressure: from 14 bar to 24 bar - depending on the hose diameter. Operating temperature: up to +135°C (mineral oil), up to +80°C (water), up to +70°C (air).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsClassic, high-quality, self-tightening rubber hose (PUSH-ON). For low-pressure hydraulic systems, pneumatic systems, and as a universal industrial hose for air, water, oils, greases, light chemicals, and cleaning fluids. Widely used in the automotive industry (no silicone used in hose production). The outer layer is resistant to weather conditions, abrasion, and oil. Flame resistance complies with MSHA 2G-14C/14 standard. Non-conductive (R > 1 MΩ/inch at 1000 V DC). Safety factor 4:1. The hose is designed to work with self-tightening PUSH-ON type fittings. Available in colors: black (BK), blue (BL), green (G), gray (GY), red (R), and yellow (Y). Inner layer: black synthetic rubber Chemivic™ (NBR + vinyl). Reinforcement: synthetic braid. Outer layer: black, blue, green, gray, red, or yellow synthetic rubber. Working pressure: 20 bar. Operating temperature: from -40°C to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly durable, universal high-quality flat hose used in the mining, oil, energy, and agriculture industries. Particularly used for water, sludge, wastewater, and fertilizers. Made from hydrolysis and microbe-resistant polyurethane - polyether. Reinforced with circumferentially woven polyester braid bonded and surrounded by polyurethane in the original hot thermoplastic polyurethane extrusion production process through braiding. The hose has high tensile strength, with minimal elongation under pressure (up to 2%) and no tendency to kink or twist. Due to its durability combined with ease of handling (unrolling, laying, storing), it is widely used in water systems (drainage of open-pit mines, water supply, drainage, and wastewater discharge) and beyond. Resistant to a wide range of chemicals, microbes, fungi, hydrolysis, weather conditions, UV, and ozone. Good abrasion resistance. Available on special order in lengths longer than 200 meters in diameters up to 6”. To confirm the resistance and application conditions of the hose, contact Tubes International. Maximum working pressure for temporary use established according to a safety factor of 2:1 approved by the manufacturer (only for water and safe, non-flammable liquids). For maximum longevity, it is not recommended to exceed 1/3 of the bursting pressure. Standard roll length: 200 m. Hose material: black polyurethane - polyether (PU). Working pressure: from 8 bar to 27 bar - depending on hose diameter and temperature. Operating temperature: from -50°C to +75°C (water).
