Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight suction and discharge hose designed for the transfer of milk and food substances, requiring the use of odorless and tasteless rubber. It contains no plasticizers, phthalates, or animal-derived substances. The special "CRUSH PROOF" hose construction with a plastic spiral allows the hose to return under pressure to its original shape after being accidentally run over, for example, by a forklift. The hose is lightweight and easy to handle. It is primarily designed for unloading milk from tankers. Not recommended for heavy-duty working conditions in process applications. Norms and requirements: 1) General: EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) Food industry, food contact: EC 1935/2004, EC 2023/2006 (GMP). Inner layer compliant with D.M. 21/03/73, FDA 21 CFR 177.2600, BfR, RAL (German Institute for Quality Assurance and Certification). Inner layer: white NR/NBR blend. Reinforcement: synthetic braid, PET spiral. Outer layer: blue synthetic rubber. Working pressure: 16 bar. Vacuum: 0.7 bar. Operating temperature: from -30°C to +85°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and discharge hose intended for the transfer of food substances, requiring the use of odorless and tasteless rubber. It does not contain phthalates and bisphenol A. The inner layer made of NBR/PVC is resistant to standard cleaning agents and processes used in the food industry. Suitable for milk and its derivatives as well as fatty food substances. Widely used in the food industry under standard operating conditions. Norms and requirements: Food industry, contact with food: 1935/2004/EC and 2023/2006/EC (GMP). D.M. 21/03/73, FDA 21 CFR 177.2600, BfR XXI cat. 2. Inner layer: white NBR/PVC rubber. Reinforcement: synthetic braid, steel spiral. Outer layer: blue synthetic rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: from -15°C to +90°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong and very flexible and elastic pressure hose reinforced with two steel braids intended for conveying saturated steam at higher pressure. The inner layer is resistant to high-temperature steam. The outer layer is resistant to high temperature and weather conditions. For steam, use special screw-on fittings designed for steam – precisely matched to the diameter and thickness of the hose. To extend the lifespan, the hose should be emptied of steam after use to avoid the accumulation of condensate. Inner layer: black EPDM rubber. Reinforcement: double steel braid. Outer layer: red micro-perforated EPDM rubber. Working pressure: 18 bar. Operating temperature: from -40°C to +210°C (temporarily up to +230°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction and discharge hose with an inner layer made of chemically resistant ultra-high molecular weight polyethylene (UPE, UHMWPE). The inner layer of UPE is resistant to most aggressive chemicals, antistatic (R<106Ω), compliant with food hose requirements, smooth, with a low friction coefficient during flow, preventing medium deposition on the walls. This significantly facilitates cleaning and allows for use in the cosmetic, pharmaceutical, and food industries. Reinforced with synthetic cord and steel spirals. The outer layer is made of chemically resistant EPDM rubber, antistatic (R<106Ω), abrasion-resistant, ozone-resistant, weather-resistant, and fire-resistant. Compliant with EN 12115:11 type Ω/T requirements, fully antistatic - ensures the dissipation of electrostatic charges through the hose walls (R<109Ω). This enables the use of the hose in explosion hazard zones. The hose is widely used for various applications in the chemical industry. Standards and requirements: Chemical hoses: EN 12115:2011 (type Ω/T). Food industry, contact with food (inner layer): 1935/2004/EC, 2023/2006/EC (GMP), 10/2011/EU (simulated fluids A, B, C, D2). Installation: use smooth fittings with a spigot ("tail" to the hose) without sharp or high ribs that could cut or damage the inner layer of UPE when tightened. The spigot diameter should be precisely matched to the hose diameter to ensure tightness. Installation with clamp sleeves or band clamps. Confirmation of resistance and application conditions requires contact with Tubes International, especially for temperatures above 50°C. Inner layer: black UPE polyethylene. Reinforcement: textile cord, steel spiral. Outer layer: black EPDM rubber. Working pressure: 16 bar. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and discharge hose designed for the transfer of liquid products from the petrochemical industry containing up to 50% aromatic hydrocarbons, fuels, gasoline, diesel, heating oil, lubricating oils, etc. The inner layer is made of black, smooth, antistatic (dissipating electric charges 10^4 Ω < R < 10^9 Ω) NBR rubber. Reinforcement with synthetic cord and steel spirals. The outer layer is made of black NBR rubber, resistant to oil and weather conditions. Relatively low weight and flexible hose construction make it easy to handle, characterized by a wide, universal application for fuel transfer or other compatible media in typical working conditions. Inner layer: black NBR rubber. Reinforcement: synthetic cord, steel spirals. Outer layer: black NBR rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: from -35°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong RIG STAR D discharge hose and RIG STAR SD suction-discharge hose are designed for the transfer and handling of crude oil, petrochemical products, and drilling cuttings mixed with crude oil (up to 50% aromatic compounds). It can also be used for cement, barite, seawater, and brine. The inner layer is made of black, smooth, antistatic NBR rubber. It features a copper wire ensuring electrical continuity between the hose ends. The outer layer is made of CR chloroprene rubber, flame-retardant, resistant to abrasion, ozone, seawater, and weather conditions. Designed as a specialized OFFSHORE hose for operation on drilling platforms. Widely used on North Sea platforms. It can also be successfully used in land applications. Inner layer: black NBR rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black CR rubber. Working pressure: 20 bar. Vacuum: 0.9 bar. Operating temperature: from -30°C to +85°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and discharge hose intended for the transfer of fuels and liquid products from the petrochemical industry, containing up to 50% aromatic compounds, including gasoline, diesel fuel, and mineral oil. It can be used for tankers, storage tanks, loading stations, and industrial equipment. The hose is widely used in industry and transport under standard working conditions. The inner layer is made of smooth, black, antistatic (R <106 Ω/m) NBR rubber. Reinforcement with synthetic cord and steel spiral. It has two copper wires ensuring electrical continuity between the hose ends – provided there is a proper connection to the ends. The outer layer is made of black SBR/NBR rubber, antistatic (R <106 Ω/m), resistant to abrasion, oil, ozone, and weather conditions. Inner layer: black NBR rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black SBR/NBR rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: from -30°C to +85°C (up to +100ºC for oil).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSoft and flexible textile-reinforced suction hose designed for conveying saturated steam. Inner layer with good resistance to high temperature and saturated steam. Outer layer resistant to temperature, abrasion, weather conditions, and ozone. The hose is widely used in the industry for low-pressure saturated steam – for light applications. For steam, use special screw-on fittings designed for steam. To extend the lifespan, the hose should be emptied of steam after use to avoid the accumulation of condensate. Inner layer: black EPDM rubber. Reinforcement: synthetic cord. Outer layer: black micro-perforated EPDM rubber. Working pressure: 6 bar. Operating temperature: from -40°C to +170°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and pressure hose made according to platinum-enhancing technology, resistant to UV and ozone. Compliant with the requirements of 1935/2004 CE, FDA 21 CFR 177.2600, USP class VI, European Pharmacopoeia 3.1.9, BfR XV, Journal Officiel Brochure 1227. At operating temperatures above +100°C, the maximum working pressure stated in the tables should be reduced by 1% for each 1°C increase in temperature. The safety factor is 4:1. Inner layer: translucent silicone. Reinforcement: four polyester braids, steel spiral (AISI 316). Outer layer: translucent silicone. Operating temperature: from -60°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and pressure hose made according to platinum-enhancing technology. The inner layer of the hose is extruded. Compliant with FDA 21 CFR 177.2600, USP Class VI, European Pharmacopoeia 3.1.9, BfR XV, Journal Officiel Brochure 1227, and CE Directive 1935/2004. Maximum vacuum 736.6 mm Hg (0.98 bar). At operating temperatures above +100°C, the maximum working pressure specified in the tables should be reduced by 1% for each 1°C increase in temperature. Inner layer: translucent silicone. Reinforcement: four polyester braids, AISI 316 steel spiral. Outer layer: translucent silicone. Operating temperature: from -60°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality pressure hose manufactured using platinum-enhanced technology. The inner layer of the hose is extruded. Compliant with FDA 21 CFR 177.2600, USP Class VI, European Pharmacopoeia 3.1.9, BfR XV A, Journal Officiel Brochure 1227, and CE Directive 1935/2004. At operating temperatures above +100°C, the maximum working pressure specified in the tables should be reduced by 1% for each 1°C increase in temperature. Inner layer: translucent silicone. Reinforcement: four layers of polyester braiding. Outer layer: translucent silicone. Operating temperature: from -60°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible suction and discharge hose intended for water, juices, beverages, and other food products, reinforced with a hard PVC spiral, which also contributes to the hose's lightweight. Additionally, the impact-resistant spiral ensures good resistance to vacuum and hose kinking. The transparent wall facilitates easy visual monitoring of the medium flow, and the absence of phthalates in the material allows the hose to be used for the transfer of milk and its derivatives, as well as alcohols with a concentration of up to 50%. It is not recommended for oils and fatty food substances. The smooth inner surface reduces flow losses and ensures ease of cleaning. The outer surface is also smooth, facilitating the installation of fittings using tapes or clamps, reducing external damage from abrasion, and aiding in keeping the hose clean. As a hose reinforced only with a hard PVC spiral, lacking a braid, it undergoes certain elongations under pressure, which should be considered in application, especially at temperatures above 40°C. Standards and requirements: Food industry, contact with food: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B, C, and D1), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: hard PVC spiral. Working pressure: from 5 bar to 7 bar, depending on the hose diameter. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible pressure hose for general purposes. Used for air, water, light chemicals, and liquid and semi-liquid food products such as water, juices, beverages, beer, wine, and alcohols with a concentration of up to 50% (and up to 20% for hoses with the index SO-PVCSTAR-CR). Not recommended for food substances containing fats and oils. Suitable for milk and its derivatives (not suitable for milk and dairy products for hoses with the index SO-PVCSTAR-CR). Phthalate-free. Standards and requirements: Food industry, food contact: compliant with European regulations 1935/2004/EC and 10/2011/EU (simulant fluids A, B, C, and D1). For hoses with the index SO-PVCSTAR-CR: 1) General: EU 2015/863 (RoHS 3), EC 1907/2006 (REACH). 2) Food industry, food contact: compliant with European regulations 1935/2004/EC and 10/2011/EU (simulant fluids A, B, and C). Hose material: transparent PVC. Reinforcement: polyester braid. Working pressure: from 8 bar to 22 bar, depending on the hose diameter. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure hose with fittings and bend restrictors designed for cold and hot water pressure washing equipment. Resistant to detergents, oils, ozone, and weather conditions. Standard fittings: GW M22 x 1.5 (AISI 304 steel). Inner layer: black synthetic rubber. Reinforcement: double steel braid. Outer layer: black, micro-perforated synthetic rubber. Operating temperature: from -10°C to +155°C. Working pressure: 500 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible suction and discharge hose intended for water, juices, beverages, and alcohols with a concentration of up to 50% (and up to 20% for hoses with the SO-PVCSTAR-MS index), and other food products. Not recommended for food substances containing fats and oils. Suitable for milk and its derivatives (however, hoses with the SO-PVCSTAR-MS index are not suitable for milk and dairy products). Reinforcement with a steel wire spiral embedded in the PVC wall provides good resistance to vacuum and hose collapse. The smooth inner surface reduces flow losses and ensures ease of cleaning. The transparent wall allows for easy visual monitoring of flow. In the absence of direct contact with food (in industry, construction, agriculture), it can be used for light chemicals, water, sludges, and wastewater, and other fluids (without fats, oils, and hydrocarbons). As a non-braided hose, it exhibits some elongation under pressure. Standards and requirements: Food industry, food contact: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulants A, B, C, and D1), 2023/2006/EC (GMP). For hoses with the SO-PVCSTAR-MS index: Food industry, food contact: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulants A, B, and C), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: galvanized steel spiral. Working pressure: from 6 bar to 11.5 bar, depending on the hose diameter. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible, bendable, and almost smooth inside hose designed for the extraction and transport of dust, powders, granules, grains, flakes, and similar lightweight materials with abrasive properties. Made from polyether-polyurethane, it has good resistance to abrasion, ozone, weather conditions, hydrolysis, and biological corrosion. Suitable for contact with food for the transport of bulk and liquid food materials, including fatty or oily substances. Not recommended for milk and its derivatives. Reinforcement with a hard PVC spiral provides good crush resistance. The antistatic version of the hose features a copper antistatic wire embedded on the outer side of the hose along the reinforcing spiral. Effective grounding of the wire ensures a sufficient level of electrostatic charge dissipation for many applications. Particularly used in the agri-food industry, plastics, building materials, etc. The WIND STAR PU hose complies with European requirements 10/2011/EU (simulants A, B, C, D2, and E) and American FDA 21 CFR 177.2600 "d", "e", "f" (dry, liquid-water, fatty). Additional information regarding food and pharmaceutical applications – see the section "Hoses for food products." Hose material: transparent polyether-polyurethane. Reinforcement: hard PVC spiral. Operating temperature: from -40°C to +80°C (working pressure dependent on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, six-layer hose designed for washing with cold and hot water as well as light chemicals. Inner layer with increased temperature resistance. Intermediate and outer layers resistant to detergents and disinfectants. Outer layer of food-grade quality, with increased resistance to greases, fats, and oils. Hose highly resistant to kinking. Recommended for use in the food industry. Compliant with European requirements for food substances EU No.10/2011 (simulated fluids A, B, C). Recommended fitting TR-THERMO-12-BZ140-08-SS. Inner layer: smooth PVC. Reinforcement: double polyester braid. Outer layer: smooth PVC. Working pressure: 50 bar. Operating temperature: from -15°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction hose designed for the transfer and handling of crude oil, petrochemical products, and drilling cuttings mixed with crude oil (up to 50% aromatic compounds). It can also be used for cement, barite, seawater, and brine. The inner layer is made of black, smooth, antistatic NBR rubber. Reinforced with layers of durable synthetic cord. It features a copper wire ensuring electrical continuity between the hose ends. The outer layer is made of CR chloroprene rubber, flame-retardant, resistant to abrasion, ozone, seawater, and weather conditions. Designed as a specialized OFFSHORE hose for operation on drilling platforms. Widely used on North Sea platforms. Can be successfully used in land applications. Inner layer: black NBR rubber. Reinforcement: synthetic cord. Outer layer: black CR rubber. Working pressure: 20 bar. Operating temperature: from -30°C to +85°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose for high pressures in cold and hot water high-pressure washing applications. Characterized by resistance to detergents, oils, ozone, and weather conditions. Inner layer: black synthetic rubber. Reinforcement: double steel braid. Outer layer: black, micro-perforated synthetic rubber. Working pressure: 500 bar. Operating temperature: from -10°C to +155°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsReady, strong, and flexible multi-braided hose, primarily used for high-pressure water cleaning and cutting, hydroforming, hydraulics, chemical injection, and high-pressure lubrication. The hose is pressure tested and supplied with the appropriate certification. It meets the EN 1829-2 standard. Inner layer: POM (polyoxymethylene). Outer layer: PA (polyamide). Material of the end fitting and sleeve: stainless steel (end fitting), carbon steel, galvanized (sleeve). Working pressure: 2500 bar. Operating temperature: from -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsReady, strong, and flexible, multi-braided hose, primarily used for high-pressure water cleaning and cutting, hydroforming, hydraulics, chemical injection, and high-pressure lubrication. The hose is pressure tested and supplied with the appropriate certification. Inner layer: POM (polyoxymethylene). Outer layer: PA (polyamide). Material of the end fitting and sleeve: stainless steel (end fitting), carbon steel, galvanized (sleeve). Working pressure: 2800 bar. Operating temperature: from -30°C to +70°C (+60° for hose SS-NW-05-6H).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsReady, lightweight, and flexible, double-braided hose used in water cutting and cleaning devices. Applications of the hose include cleaning chemical and energy installations, heat exchangers, cleaning and cutting concrete structures, road surfaces, and cleaning steel surfaces. The hose is pressure tested and supplied with the appropriate certificate. Inner layer: polyoxymethylene. Outer layer: polyamide. Material of fittings and sleeves: carbon steel, galvanized. Working pressure: up to 1200 bar, depending on diameter. Operating temperature: from -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsReady, lightweight, and flexible, double-braided hose used in water cutting and cleaning devices. Applications of the hose include cleaning chemical and energy installations, heat exchangers, cleaning and cutting concrete structures, road surfaces, and cleaning steel surfaces. The hose is pressure tested and supplied with the appropriate certification. Inner layer: polyoxymethylene. Outer layer: polyamide. Fittings and sleeves material: carbon steel, galvanized. Working pressure: up to 1000 bar. Operating temperature: from -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStandard hydraulic end (type Z - with a regular hydraulic "tail" for hose), with external BSP thread, flat sealing - requires the use of an additional flat gasket (AGR-F). Designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the type of hose. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStandard hydraulic end (type Z - with a regular hydraulic "tail" for the hose), with external BSP thread, 60° sealing cone (AGR). Designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the type of hose. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStandard hydraulic end fitting (type Z - with a regular hydraulic "tail" for hose), with internal metric thread and nut, sealing with an O-ring on a 24° cone (DKOL), 90° angled, lightweight series. Designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the hose type. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose designed for the transfer of liquid products from the petrochemical industry containing up to 50% aromatic hydrocarbons, fuels, gasoline, diesel, heating oil, lubricating oils, etc. Inner layer made of black, smooth NBR rubber. Reinforcement with synthetic cord. It has copper wires ensuring electrical continuity between the hose ends – provided that it is correctly connected to the fittings. Outer layer made of black NBR rubber, resistant to oil and weather conditions. Relatively low weight and flexible hose construction make it easy to handle, characterized by a wide, universal application for fuel transfer or other compatible media under typical working conditions. Inner layer: black NBR rubber. Reinforcement: synthetic cord. Outer layer: black NBR rubber. Working pressure: 10 bar. Operating temperature: from -30°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStandard hydraulic end fitting (type Z - with a regular hydraulic "tail" for hose), with internal metric thread and nut, sealing with an O-ring on a 24° cone (DKOS), 90° angled, heavy series. Designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the hose type. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStandard hydraulic end fitting (type Z - with a regular hydraulic "tail" for hose), with internal metric thread and nut, O-ring seal on a 24° cone (DKOS), heavy-duty series. Designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the hose type. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStandard hydraulic end fitting (type Z - with a regular hydraulic "tail" for hose), with metric tube, sealing with a cutting ring (BEL), angled 45° light series. Designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the hose type. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStandard hydraulic end fitting (type Z - with a regular hydraulic "tail" for hose), with metric tube, sealing with a cutting ring (BEL), 90° angled light series. Designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the hose type. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStandard hydraulic end fitting (type Z - with a regular hydraulic "tail" for the hose), with a metric tube, sealing with a cutting ring (BEL), lightweight series. Designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the hose type. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStandard hydraulic end (type Z - with a regular hydraulic "tail" for hose), with metric tube, sealing with a cutting ring (BES), angled 45° heavy series. Designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the type of hose. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStandard hydraulic end (type Z - with a regular hydraulic "tail" for hose), with metric tube, sealing with a cutting ring (BES), angular 90° heavy series. Designed for crimping in hydraulic and industrial hoses using a crimping sleeve suitable for the type of hose. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsWelding stub, type WRS, for flange EN 1092-1 PN16 for installation with RS shell clamp or for tightening with sleeve TI-LR, TI-LDR. Material: carbon steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket and plug (reducer) of CAMLOCK DA connection made according to the American military standard MIL-C-27487 (A-A-59326). Commonly used as a transfer connection, particularly in the petrochemical industry. Working pressure: up to 10 bar, depending on the size of the connection. Material: aluminum. Levers: AISI 304 steel (in sizes 1.1/4" to 4" - levers made of brass). Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlat gasket for SAE flanges. Material: polyurethane.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlat gasket IBC for flange PN made according to standard PN-EN 1514-1. The permissible working pressure at which a given gasket can be used depends on the temperature and type of medium (selection should be agreed with TUBES INTERNATIONAL®). When selecting a gasket, attention should be paid to the outer diameter dimension, appropriate for the flange class. For example: gasket DN 10 PN40 is suitable for classes PN10, PN16, and PN25. Material: KLINGER SIL 4430. Working pressure: up to 100 bar. Operating temperature: from -200°C to +400°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlat gasket IBC for flange PN made according to standard PN-EN 1514-1. The permissible working pressure at which a given gasket can be used depends on the temperature and type of medium (selection should be agreed with TUBES INTERNATIONAL®). When selecting a gasket, attention should be paid to the outer diameter dimension, appropriate for the flange class. For example: gasket DN 10 PN40 is suitable for classes PN10, PN16, and PN25. Material: PTFE. Working pressure: up to 300 bar. Operating temperature: from -200°C to +220°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFerrari lever connector plug with hose end, type F.8, for use in agriculture, horticulture, industry, construction, road and tunnel building, groundwater drainage, wastewater treatment, sewage disposal, environmental protection. Material: carbon steel, galvanized. Operating temperature: from -20°C to +50°C.
