Our products
Select options This product has multiple variants. The options may be chosen on the product page / DetailsShell clamp designed for securing hoses on standard ends (smooth) with a safety flange. Material: AISI 316 steel. Working pressure 25 bar (with appropriately selected hose and end EN 14420-3).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsTwo-part clamp, manufactured in accordance with (for hose diameter 38 mm) or similar (from hose diameter 50 mm) to DIN 20039 A standard, with separate inserts - "pressure tongues." Designed for mounting ends and connections with the hose part ("tail") without a lock (safety flange), made of high-quality ductile cast iron galvanized (with yellow passivation free of hexavalent chromium). Indices from LU-SL-400 to LU-SL-988 are additionally reinforced and intended for large diameters. Material: galvanized ductile cast iron. With proper installation, appropriately selected hose, and end fitting, working pressure up to 16 bar.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsL-type sleeve designed for crimping hydraulic type ends (ends for high-pressure hoses type Z) in industrial hoses (rubber and plastic with textile reinforcement, possibly with a reinforcing spiral - suction and pressure hoses). The sleeve should be selected considering the internal diameter Dw and external diameter Dz of the hose. The length of the sleeve L should not exceed the length of the tail of the end Lk. Diameter D1 [mm] - external diameter. Diameter D2 [mm] - internal diameter. Diameter D3 [mm] - locking diameter. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTwo-part clamp according to DIN 20039 B, with hooks ("claws") and separate pressure pads ("tongues"), made of high-quality ductile cast iron galvanized (with yellow passivation free from hexavalent chromium). Designed for securing hoses, with a connection to the hose part featuring a locking mechanism. Indices marked with the letters "FL" are intended for flat hoses. Material: galvanized ductile cast iron. With proper installation, appropriately selected hose, and fitting, working pressure up to 25 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsShell clamp designed for securing hoses on standard ends (smooth) with a securing flange. Material: clamps - aluminum, screws and nuts - galvanized carbon steel. Working pressure: 25 bar (with appropriately selected hose and end EN 14420-3).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLDR, LD, LR type sleeves are designed for clamping hygienic stainless steel ends (with a corrugated tail) type NH-xxK-xxx and ends with a tail for hose under a shell clamp RS, e.g., TW-KRS-xxx, NH-xxR-xxx in industrial hoses (rubber and plastic with textile reinforcement, possibly with a reinforcing spiral - suction and pressure hoses). The sleeve should be selected considering the internal diameter Dw and external diameter Dz of the hose. The length of the sleeve L may be slightly (a few mm) greater than the length of the tail of the end Lk. LR sleeves - only for ends under the shell clamp, LD - only for ends with a corrugated tail, LDR - sleeves for both types of ends. Diameter D1 [mm] - external diameter. Diameter D2 [mm] - internal diameter. Diameter D3 [mm] - locking diameter. Material: AISI 304 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsShell clamp according to EN 14420-3 (DIN 2817) designed for securing hoses at ends with a safety flange. DN - internal diameter of the hose x wall thickness of the hose. Material: AISI 316 steel. Working pressure: 25 bar (with appropriately selected hose and end EN 14420-3).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThree-part clamp according to DIN 20039 B, with hooks ("claws") on the flange to secure the ends and with separate inserts - "tongues" for pressing. Material: ductile cast iron galvanized. With proper installation, appropriately selected hose and fitting, working pressure up to 25 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsL-type sleeve designed for crimping hydraulic type ends (ends for high-pressure hoses type Z) in industrial hoses (rubber and plastic with textile reinforcement, possibly with a reinforcing spiral - suction and pressure hoses). The sleeve should be selected considering the internal diameter Dw and external diameter Dz of the hose. The length of the sleeve L should not exceed the length of the tail of the end Lk. Diameter D1 [mm] - external diameter. Diameter D2 [mm] - internal diameter. Diameter D3 [mm] - locking diameter. Material: AISI 304 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsShell clamp according to EN 14420-3 (DIN 2817) intended for securing hoses at ends with a safety flange. DN - internal diameter of the hose x wall thickness of the hose. Material: clamps - aluminum, screws and nuts - galvanized carbon steel. Working pressure: 25 bar (with appropriately selected hose and end EN 14420-3).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTwo-part clamp with integrated, cast pressure "tongues." The clamp is designed for mounting ends and connections with a hose part ("tail") without a lock (safety flange), made of high-quality ductile cast iron, galvanized (with yellow passivation free of hexavalent chromium). Material: galvanized ductile cast iron. With proper installation, appropriately selected hose, and end fitting, working pressure up to 16 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsL-type sleeve designed for crimping hydraulic type ends (ends for high-pressure hoses type Z) in industrial hoses (rubber and plastic with textile reinforcement, possibly with a reinforcing spiral - suction and pressure hoses). The sleeve should be selected considering the internal diameter Dw and external diameter Dz of the hose. The length of the sleeve L should not exceed the length of the tail of the end Lk. Diameter D1 [mm] - external diameter. Diameter D2 [mm] - internal diameter. Diameter D3 [mm] - locking diameter. Material: AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsShell clamp designed for securing hoses on standard ends (smooth) with a securing flange. Material: clamps - brass, screws and nuts - galvanized carbon steel. Working pressure 25 bar (with appropriately selected hose and end EN 14420-3).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLDR, LD, LR type sleeves are designed for clamping hygienic stainless steel ends (with a corrugated tail) type NH-xxK-xxx and ends with a tail for hose under a shell clamp RS, e.g., TW-KRS-xxx, NH-xxR-xxx in industrial hoses (rubber and plastic with textile reinforcement, possibly with a reinforcing spiral - suction and pressure hoses). The sleeve should be selected considering the internal diameter Dw and external diameter Dz of the hose. The length of the sleeve L may be slightly (a few mm) greater than the length of the tail of the end Lk. LR sleeves - only for ends under the shell clamp, LD - only for ends with a corrugated tail, LDR - sleeves for both types of ends. Diameter D1 [mm] - external diameter. Diameter D2 [mm] - internal diameter. Diameter D3 [mm] - locking diameter. Material: galvanized carbon steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTwo-part clamp, USA version, with hooks ("claws"), made of high-quality ductile cast iron galvanized (with yellow passivation free of hexavalent chromium). Designed for hose mounting, with a connection to the hose part with a locking mechanism. Material: galvanized ductile cast iron. With proper installation, appropriately selected hose, and fitting, working pressure up to 25 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsShell clamp designed for securing industrial hoses on smooth or corrugated ends with a protective flange. It is closed by tightening in a vice and driving in a stainless steel mounting pin (included). It features smaller external dimensions than screw-type shell clamps. Material: clamps - aluminum, pin - stainless steel. Working pressure: 25 bar (with appropriately selected hose and end EN 14420-3).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTwo-part clamp, design similar to DIN 20039 A standard, with separate inserts - "tongues" for clamping. Intended for mounting ends and connections with a hose part ("tail") without a lock (safety flange). Material: AISI 316 steel. With proper installation, appropriately selected hose and end fitting, working pressure up to 16 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAuxiliary long screw DIN912 for mounting shell clamps RS and SC, used during assembly to enable proper compression of the clamps on the hose. After compression, they are subsequently replaced with short mounting screws from the clamp set. Material: galvanized carbon steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLDR, LD, LR type sleeves are designed for clamping stainless steel hygienic ends (with a corrugated tail) type NH-xxK-xxx and ends with a tail for hose under a shell clamp RS, e.g., TW-KRS-xxx, NH-xxR-xxx in industrial hoses (rubber and plastic with textile reinforcement, possibly with a reinforcing spiral - suction and pressure hoses). The sleeve should be selected considering the internal diameter Dw and external diameter Dz of the hose. The length of the sleeve L may be slightly (a few mm) greater than the length of the tail of the end Lk. LR sleeves - only for ends under the shell clamp, LD - only for ends with a corrugated tail, LDR - sleeves for both types of ends. Diameter D1 [mm] - external diameter. Diameter D2 [mm] - internal diameter. Diameter D3 [mm] - locking diameter. Material: AISI 316 steel.
