Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuite lightweight, flexible, and pliable, temperature-resistant two-layer suction hose designed for the discharge of vapors, smoke, and high-temperature air. Flame-retardant, resistant to hot sparks within a certain range. Used with furnaces and engines for the extraction of high-temperature gases in the metallurgical, ceramic, shipbuilding, aerospace, automotive, and military equipment industries. Characterized by high compressibility - up to 1:6, strong construction due to glass fabric reinforced with stainless steel threads, and impact resistance thanks to the external spiral. Used exclusively as a suction hose operating under vacuum, due to the possibility of gas permeation outside under pressure (degassing). Also available with a stainless steel spiral (from a diameter of 80 mm). Hose installation on couplings with bridge clamps (left-handed). Standard length: from 2 to 10 m - contact Tubes International. Hose material: 2 layers of impregnated glass fabric with stainless steel fibers, gray. Reinforcement: external spiral made of galvanized steel wire and sheet. Operating temperature: from -50°C to +650°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose in a double version (two hoses with a welded outer layer) designed for hydraulic oil installations, fuels, and water-based fluids. Available on request in micro-perforated form (for gases and air). Inner layer: polyester. Reinforcement: steel braid. Outer layer: polyurethane. Working pressure: from 190 bar to 325 bar, depending on the hose diameter. Operating temperature: from -40°C to +100°C (for water and air up to +70°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThick, strong, flexible, crush-resistant pressure hose designed for the transmission of hot, dry air from the compressor to the tank installation of the tanker. Used in road tankers for the transport of bulk materials: cement trucks, feed trucks, etc., as well as in other industrial installations. The outer layer is resistant to ozone and weather conditions. Standard length: 60 m or 120 m. Inner layer: white EPR rubber. Reinforcement: synthetic cord. Outer layer: blue EPDM rubber. Working pressure: 10 bar. Operating temperature: from -40°C to +200°C (temporarily up to +240°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHand crimping tool TNT250/B (six-jaw crimp) for air conditioning. The crimping head allows it to be passed through the hose, which is important when crimping angled ends. The set includes: 6 sets of jaws for standard hoses and those with reduced outer diameter, grease, plastic caliper, case.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSTORZ cap, equipped with a chain to prevent loss, intended for transmission installations for liquid and bulk substances. Used in firefighting, irrigation systems, chemical industry, food industry, agriculture, etc. With a symmetrical design of the connection part, it easily connects with each other. Elements with the same hook spacing can be connected. Available in a forged version with a working pressure of up to 16 bar and in a cast version, characterized by significantly lower strength with a working pressure of up to 6 bar. Material: aluminum. Working pressure: 16 bar (forged connections), 6 bar (cast connections). Seal: white NBR rubber (forged connections), black NBR rubber (cast connections).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThrottle-return valve type MRF HTC series HIGH-FLOW for direct mounting in actuator connections, used in pneumatic systems for regulating the flow rate of compressed air and the direction of flow. Recommended for applications requiring high flow rates during both filling and venting. Equipped with a plug connection for easy disassembly of pneumatic hoses. Adjustment change via a control knob and/or screwdriver; possibility of securing the setting with a locking nut. Size: 1/8″, 1/4″. Working pressure: up to 10 bar. Operating temperature: from -10°C to +50°C. Material: plastic.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight connector KN designed for quick and efficient assembly of suction hoses using BC screw bridge clamps. Material: galvanized steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure adaptor type A107K with nut, featuring external BSP threads (60° cone sealing). Material: AISI 316L steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThree-way manifold block allowing the connection of multiple high-pressure hoses to a single pump, as well as the connection of a pressure gauge. Made of black zinc-coated steel. Flow diameter 5 mm (3/16"). Connections: 2 x 1/4" BSP, 1 x 1/2" BSP (NBR o-ring). Connection sealing: internal cone 120°. Working pressure: 2000 bar (maximum working pressure when using a metal-rubber seal is 1000 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsEnd fitting for thermoplastic and rubber hydraulic hoses for high-pressure gases with internal Whitworth thread W21.8 x 1/14" L (LEFT THREAD), connection according to PN-81/M-69229 (DIN477-1 no. 1). Intended for: among others, hydrogen, methane, other combustible gases. Material: AISI 304 steel - fitting, brass - nut.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCrimped end with internal thread, type FALP, for Teflon brake hoses. Material: carbon steel, chrome-plated.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlastic hose cutter for diameters ranging from 3 to 15 mm. Color: black. Blade material: stainless steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSafety clamp for STORZ connection to prevent disconnection. It consists of a bent galvanized steel band and a rubber collar. The clamp must be selected for the specific DN size of the connection. Band material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight coupling type LET-LOK® with internal BSP thread for metric tubing, primarily intended for the chemical, petrochemical, pharmaceutical, energy, nuclear power, and process engineering industries. The permissible working pressure is determined based on the outer diameter and wall thickness of the tubing (details in the attachment). Material: AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMRA regulator series BIT. Version used for pressure regulation in water installations, without secondary venting. Pressure gauge connection: GW 1/8" BSP. Output pressure range: 0 ÷ 2 bar, 0 ÷ 4 bar, or 0 ÷ 12 bar. Supply pressure: up to 13 bar. Operating temperature: up to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe aluminum tool case contains a complete set of tools necessary for the quick installation of air conditioning ducts using the BURGACLIP system. The set includes special pliers for installing BURGACLIP air conditioning clamps, equipped with a ratchet mechanism for easier use; a manual hose cutter designed for air conditioning hoses type BU-3090 in sizes DN 8, 10, 13, 16; and a dual-range manual cutting device for rubber and plastic hoses with an outer diameter of up to 42 mm, with the ability to pre-set the cutting blade for specific hose diameters of 6 mm and 26 mm. The blade shape allows for efficient cutting with minimal effort. An ideal solution for automotive workshops that provide services for repairing automotive air conditioning ducts.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible compressed air hose with good resistance to mineral oils. Very abrasion-resistant. The yellow color ensures excellent visibility of the hose. The hose has a thickened outer layer every 20 m, marked on the hose ("TAGLIO / CUT"), and it is recommended to cut the hose and install fittings at these points. This reinforces the fitting installation area and makes it more resistant to bending. From a 60 m roll, three 20 m hoses with fittings can be made. However, it is also possible to use the hose with fittings installed in non-thickened areas. The hose is used for pneumatic hammers and drills. Inner layer: black PVC/NBR blend. Reinforcement: double polyester braid. Outer layer: black or yellow PVC/PU blend. Working pressure: 20 bar - dependent on temperature. Operating temperature: from -10°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible and bendable, chemically resistant two-layer hose designed for the discharge of the most aggressive chemical vapors, gases, dust, and fibers (non-abrasive). Very good chemical resistance to aggressive chemicals due to the internal layer of PTFE film. In the standard version, the internal layer of white natural PTFE meets food industry requirements (FDA). In the antistatic version EL, the black internal layer of PTFE is electrically conductive (R ≤106 Ω). The hose features high compressibility - up to 1:6, a strong construction resistant to vibrations, stretching, and tearing, and impact resistance due to the external spiral. Resistant to UV radiation, ozone, and aging. Used in the chemical and food industries. Also available with a stainless steel spiral (from a diameter of 80 mm). Hose installation on couplings with bridge clamps (left-handed). Chemical resistance verification - chemical resistance table for PTFE (preliminary selection), confirmation of resistance and application conditions - by Tubes International. Standard length: from 2 to 10 m. Hose material internal layer: white PTFE Teflon film - standard version PETEF, black conductive PTFE Teflon film - antistatic version PETEF EL. Hose material external layer: polyethylene fabric coated with polyethylene (PE). Reinforcement: external spiral made of galvanized steel wire and sheet. Operating temperature: from -40°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose designed for hydraulic oil installations, gases, air, fuels, water-based fluids. Standards: SAE 100R18, ISO 3949-R18. Installation: use fittings type Z. Inner layer: polyester. Reinforcement: double polyester braid. Outer layer: polyurethane. Working pressure: from 210 bar to 250 bar, depending on hose diameter. Operating temperature: from -40°C to +100°C (for water and air up to +70°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPressure hose for plastering. Inner layer made of rubber with good abrasion resistance (70±5 mm³ according to ISO 4649 / DIN 53516). Both inner and outer layers are antistatic to prevent the accumulation of electric charges. Multiple reinforcement with synthetic cord ensures high pressure resistance. Outer layer resistant to abrasion, weather conditions, and ozone. Used for spraying wet mortar: cement, plaster, and gypsum in construction work. Commonly used with plastering machines. Fitted with special ends for plastering. The NIAGARA LIGHT hose is an economical version with a slightly thinner wall (marked with the letter "L" at the end of the index). Standard length: 60 m and 40 m LIGHT version (or 120 m - contact Tubes International). Inner layer: black SBR/NR rubber. Reinforcement: synthetic cord. Outer layer: black SBR/NR rubber. Working pressure: 40 bar. Operating temperature: from -40°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCAMLOCK ER connector plug (reduction) with a ribbed end for hose made according to the American military standard MIL-C-27487 (A-A-59326), commonly used as a transfer connection, particularly in the petrochemical industry. Working pressure: up to 10 bar. Material: aluminum.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal mechanical control distribution valve, lever with roller assistance, commonly used for controlling actuator operation. Can be mounted in any position. Function 3/2 - three-way, two-position. Size: 1/8". Material: valve body - aluminum, slider - nickel-plated aluminum, sealing - NBR, end cover - plastic. Working pressure: up to 10 bar. Operating temperature: -10°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSymmetrical straight reducing coupling KRS designed for quick and efficient assembly of suction hoses using BC worm bridge clamps. Material: galvanized steel.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° angled plug connector with a long spigot, type R47, designed for connecting wires and other components in pneumatic systems. Easy and quick to use for multiple assemblies without loss of sealing on the mechanical and pneumatic sides. Material: plastic. Working pressure: 12 bar. Working medium: vacuum, air. Operating temperature: from -20°C to +60°C. Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° high-pressure adaptor type A116N with external BSP thread (sealing ISO-1179 type G: o-ring with retaining ring) adjustable and with external BSP thread (60° cone sealing). Material: AISI 316L steel.
- Select options This product has multiple variants. The options may be chosen on the product page / Details45° elbow (R = 1.5 x d) KSBB 45 designed for quick and efficient installation of suction hoses using BC screw bridge clamps. Material: galvanized steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsEnd fitting for thermoplastic and rubber hydraulic hoses for high-pressure gases with internal Whitworth thread W21.8 x 1/14", connection according to PN-81/M-69229 (DIN477-1 no. 6). Intended for: among others: ammonia, argon, carbon dioxide, helium. Material: AISI 304 steel - fitting, brass - nut.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBANJO 15° crimp fitting for Teflon brake hoses. Material: carbon steel, chrome-plated.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsParallel mounting strip for wires of different diameters. Material: acetal resin. Color: black. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsReducing nipple with external thread enabling the connection of quick couplings and UHP hoses, as well as connecting to UHP connection blocks. Working pressure: from 2000 bar to 3000 bar (depending on thread size). Material: carbon steel, black galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight coupling type LET-LOK® with external NPT thread for metric tubing, primarily intended for the chemical, petrochemical, pharmaceutical, energy, nuclear power, and process engineering industries. The allowable working pressure is determined based on the outer diameter and wall thickness of the tubing (details in the attachment). Material: AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsNEW DEAL series lubricator with BSP thread connection ensures proper lubrication of devices with oil mist in pneumatic installations and is characterized by high dosing stability. Supply pressure: up to 18 bar. Operating temperature: up to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPin for CAMLOCK connection, type P. Material: AISI 304 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSpecial hand pliers made of strong material designed for quick and easy installation of clamp bands for the BURGACLIP air conditioning system. Equipped with a ratchet mechanism for easier use. A functional tool that also works well in hard-to-reach places, such as the engine compartment of a passenger car. The pliers ensure the tightness and durability of the connection. An ideal solution for automotive workshops that provide services for repairing automotive air conditioning lines.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAF-TH clamping sleeve for HYPERLINE SB, FX, V type PTFE hoses. Diameter D1 [mm] - outer diameter. Diameter D2 [mm] - locking diameter. Diameter D3 [mm] - inner diameter. Material: carbon steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction and discharge hose designed for the extraction or pneumatic transport of dry abrasive substances. The inner layer is made of white, smooth, abrasion-resistant rubber (80 mm³ according to ISO 4649, formerly DIN 53516), compliant with FDA 21 CFR 177.2600 requirements for food contact. Two built-in copper wires that, when grounded (or connected to a grounded end), dissipate electric charges. The outer layer is resistant to weather conditions and ozone. The hose is intended for the transport of dry food substances: grains, sugar, powders, feeds, granules, etc. (under FDA requirements) and other abrasive substances such as PVC granulate, for which a white, non-staining inner layer is required. Not intended for use in ATEX explosion hazard zones. Standards and requirements: food industry, food contact: 1935/2004/EC, 2023/2006/EC (GMP), BfR XXI cat.4. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: white NR/SBR rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black EPDM rubber. Working pressure: from 6 bar to 8 bar, depending on the hose diameter. Vacuum: 0.9 bar. Operating temperature: -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThrottle valve series RFL type B, regulating the airflow value in both directions. It is used to control the working speed of actuators in pneumatic systems. Size: M5, 1/8″, 1/4″, 3/8″, 1/2″. Working pressure: up to 10 bar. Operating temperature: up to +70°C. Body material: aluminum. Housing material: brass.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlange connection set (EN 1092), type SZ1. Included: DIN931 bolts - 4 pieces, DIN934 nuts - 4 pieces, and DIN125A washers - 4 pieces. Mechanical property class: 5.6 - bolts; 8 - nuts; 140HV - washers. Selection of bolts and nuts for flanges according to the table in the appendix. Material: carbon steel, electro-galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSTORZ adaptor with internal BSP thread intended for transmission installations for liquid and bulk substances. Used in firefighting, irrigation systems, chemical industry, food industry, agriculture, etc. Characterized by a large, unobstructed flow diameter. With a symmetrical design of the connection part, it easily connects with each other. Elements with the same hook spacing can be connected. Material: stainless steel. Working pressure: 16 bar. Seal: viton.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° angle fitting JIC 37° with external UNF thread (seal on external 37° cone). Material: AISI 316 steel.
