Strong industrial suction hose for water and compressed air, designed for operation in harsh conditions in industry, road construction, and even in quarries. Inner layer resistant to oil mist. Abrasion and weather resistant. Widely used and proven in various industrial applications. Hose available in black and yellow. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black SBR rubber. Reinforcement: synthetic cord. Outer layer: black or yellow EPDM rubber. Working pressure: 20 bar. Operating temperature: from -30°C to +70°C.

Widely used for washing floors and industrial equipment with hot water. Also suitable for outdoor use. Resistant to weather conditions and abrasion. Not resistant to oil, not recommended for air with oil mist. Compared to the "Tubes 2116," it has a thicker wall. Inner layer: white EPDM rubber. Reinforcement: polyester braid. Outer layer: red or blue micro-perforated EPDM rubber. Working pressure: 10 bar. Operating temperature: from -40°C to +100°C.

Strong pressure hose designed for the transmission of water or compressed air in irrigation systems, agriculture, mines, construction sites, etc. The inner layer is smooth, ensuring minimal flow loss. The outer layer is slightly longitudinally ribbed, which increases abrasion resistance and protects against contact with hot elements. Resistant to abrasion, ozone, weather conditions, oil, fuels, and a wide range of chemicals. Lighter and more flexible than standard rubber hoses. Flat when at rest, facilitating handling and storage. Does not require washing and drying. Resistant to longitudinal loads – during unwinding and pulling (longitudinal force should never exceed 1/3 of the specified breaking force, installation of fittings should consider longitudinal force). Use for air should always be preceded by a risk analysis in case of accidental disconnection or rupture of the hose. Hose material: black NBR/PVC blend embedded in a polyester-polyamide braid during the hose extrusion process. Working pressure: from 10 bar to 25 bar (water), from 7 bar to 18 bar (air) - depending on the hose diameter. Operating temperature for water: from -20°C to +80°C, temporarily up to +100°C.

Hose designed for cooling water in foundries, casting plants, and all applications where rubber hoses operate close to a heat source. Glass fiber covering resistant to temperatures up to +530°C caused by thermal radiation. Used in cooling systems. Particularly recommended for water installations near metallurgical furnaces. Resistant to short-term exposure to splashes of molten hot metal. Roll length: 60 m or 120 m. Inner layer: black EPDM rubber. Reinforcement: synthetic cord. Outer layer: EPDM rubber covered with glass fiber. Working pressure: 10 bar. Operating temperature: from -40°C to +120°C, external up to +530°C.

Very lightweight economical hose, flat in a resting state, designed for water transmission. An economical solution for low working pressures and non-demanding working conditions. Used in agriculture, e.g., for irrigation of crops, construction, and other industrial sectors. Hose material: blue PVC. Reinforcement: polyester layer. Working pressure: 3 bar. Operating temperature: from -5°C to +60°C.

Hose designed for the transmission of compressed air, for compressors, hammers, drills, and other pneumatic tools. Due to its low weight, flexibility, robust construction, and high working pressure, it has been accepted and successfully used for many years in construction (particularly in demolition companies), industry, and mining. Extremely durable and long-lasting due to high-quality materials and construction. Reinforced with a circumferentially woven polyester braid completely bonded and surrounded by rubber in the original hot extrusion process of the rubber mixture through the braid. UV resistant. The inner layer is smooth, ensuring minimal flow loss. The yellow, ribbed outer surface is resistant to abrasion, oils, and ozone, and is highly visible on construction sites. Flat when at rest, facilitating handling and storage. Resistant to longitudinal loads. Most commonly used with air couplings (spacing 42 or 41 mm) mounted with cast iron clamps (ordered separately). Also available in black. Use for high-pressure air should always be preceded by a risk analysis in the event of accidental disconnection or rupture of the hose and potential application of safeguards. Maximum working pressure established according to a safety factor of 4:1 approved by the manufacturer for air. Exceeding 1/3 of the specified breaking force is not recommended. Standard roll length: 200 m. Hose material: yellow NBR/PVC mixture with UV-resistant barrier, embedded in the polyester braid during the hose extrusion process. Working pressure: from 12.5 bar to 25 bar - depending on the hose diameter and temperature. Operating temperature: from -30°C to +75°C (temporarily up to +80°C).

Lightweight, abrasion-resistant pressure hose designed for the transmission of drinking water in large quantities under high working pressure. Flat in a resting state, which facilitates handling and storage. With minimal elongation under pressure and no tendency to kink or twist. Reinforced with a circumferentially woven polyester braid, completely bonded and surrounded by thermoplastic polyurethane in the original hot extrusion production process through braiding. Meets requirements for the transmission of cold drinking water: PZH (no. B.BK.60110.0171.2022, valid until 01.04.2025), KTW-DVGW, WRAS(BS6920), and NSF61. Intended for permanent, temporary, and emergency drinking water supply installations. Used for delivering water to ships, in military field installations, humanitarian actions, mass event services, festivals, etc. Available in other diameters up to 305 mm upon special request. Maximum working pressure for temporary use established according to a safety factor of 2:1 approved by the manufacturer (only for water and safe, non-flammable liquids). To maximize lifespan, it is not recommended to exceed 1/3 of the bursting pressure and the specified breaking force. Standard roll length: 200 m. Hose material: blue polyurethane - polyether (PU) embedded in the braid (textile spacer) in the hose extrusion process. Working pressure: from 18 bar to 25 bar - depending on the hose diameter and temperature. Operating temperature: from -50°C to +75°C (for clean water).

Very lightweight and flexible flat-folded suction hose for water for hydrants and fire pumps, without fittings. The hydrant hose complies with the EN 14540 standard and is used in internal hydrants according to EN-671-2. The hose for pumps is used for fire, rescue, and forestry motor pumps. In addition to fire-fighting functions, it is widely used in industry, construction, agriculture, and mining. It can be used for the transmission of water, seawater, industrial water, and solutions of certain chemical substances. The inner layer is smooth, resistant to mold and rot. The outer layer (braid) is of high strength, resistant to weather conditions and abrasion. Also available in a yellow luminescent version (DN52, DN75, 20m, for pumps). Certifications (Poland): Hoses comply with the technical conditions of the MSWiA Regulation of April 27, 2010. Inner layer: PVC insert (PU for DN110). Reinforcement: polyester braid. Working pressure: from 12 bar to 15 bar - depending on the hose diameter. Operating temperature: from -30°C to +60°C.

Very lightweight, flat (at rest) industrial PVC suction hose. Thanks to the appropriately selected textile reinforcement with a polyester liner, it has good resistance to elongation. Designed for pressure transmission of water and other liquids. Widely used in agriculture, construction, shipbuilding, mining, etc. Standard roll length: 50 m or 100 m. Inner layer: black PVC. Reinforcement: polyester liner. Outer layer: blue PVC. Working pressure: from 2.5 bar to 8.5 bar - depending on the hose diameter and temperature. Operating temperature: from -5°C to +60°C.

High-pressure, highly durable hose for compressed air transmission. Designed for use in harsh conditions such as construction sites, mines, etc., to power equipment with high compressed air consumption. Extremely robust and durable due to high-quality materials and a double-layer construction – double reinforcement with circumferentially woven high-strength polyester braid, completely covered and lined with thermoplastic polyurethane (PU). The hose has very good abrasion resistance, is puncture-resistant, tear-resistant, and oil-resistant. The hose does not elongate under pressure and is resistant to longitudinal loads. Flat in a resting state, which facilitates handling and storage. Available as ready-made hoses of 20 or 40 m in length, with factory-installed fittings. Use for high-pressure air should always be preceded by a risk analysis in case of accidental disconnection or rupture of the hose and potential application of safeguards. The maximum working pressure of the hose is established according to a safety factor of 4:1 approved by the manufacturer for air. Exceeding 1/3 of the specified breaking force is not recommended. Hose material: polyurethane (PU). Reinforcement: double polyester braid. Outer layer: orange polyurethane (PU). Working pressure: from 30 bar to 43.75 bar - depending on the hose diameter. Operating temperature: from -50°C to +110°C.

Strong, flexible rubber fire hose, designed for use on reels. The ANKARA EN hose is manufactured according to the EN 694 standard, which is the European standard for hoses used in fixed fire protection installations and commonly used on reels in fixed hydrants in buildings, industrial installations, shopping centers, etc. The inner layer is made of EPDM rubber, resistant to light chemicals and fire-fighting foaming agents. The outer layer is made of EPDM rubber, resistant to abrasion and weather conditions. It performs excellently when mounted on reels, ensuring water flow even when the hose is not fully extended. The presented ANKARA hose is made according to the requirements of the older DIN 14817: 1991 standard, intended for powder and foam extinguishing agents, with an inner layer made of conductive NR/SBR rubber and a working pressure of up to 20 bar, also designed for use on reels. Inner layer: EPDM rubber (ANKARA EN), conductive NR/SBR rubber (ANKARA). Reinforcement: synthetic cord. Outer layer: EPDM rubber (ANKARA EN), SBR rubber (ANKARA). Working pressure: from 7 bar to 20 bar - depending on the size and type of hose. Operating temperature: from -20°C to +60°C (ANKARA EN), from -40°C to +70°C (ANKARA).

Extremely lightweight, flexible water delivery hose designed for internal fire protection of buildings. The inner layer is made of high-quality synthetic rubber. The outer layer consists of a strong, dense polyester braid reinforced with a thin, tightly wound PET spiral. The hose is used in internal hydrant cabinets with a length of 20 m to 30 m of hose wound on a drum (reel) with a nozzle mounted at the end of the hose. Compliant with EN 694 standard for fire hoses (type B class 5). In the field of fire protection (Poland), it has a CNBOP-PIB compliance certificate. It can also be used in industry - for seawater, industrial water, and some light diluted chemicals, as well as for air, dust, and light solid particles. It is not intended for use in harsh external conditions. Installation with clamps or crimping sleeves on ends with smooth, sharp-free fittings to avoid cutting the inner layer. Inner layer: smooth synthetic rubber. Reinforcement: polyester braid with a reinforcing spiral (thread) PET. Working pressure: from 7 bar to 12 bar - depending on the hose diameter. Operating temperature: from -20°C to +60°C.