Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight suction and discharge hose designed for the transfer of milk and food substances, requiring the use of odorless and tasteless rubber. It contains no plasticizers, phthalates, or animal-derived substances. The special "CRUSH PROOF" hose construction with a plastic spiral allows the hose to return under pressure to its original shape after being accidentally run over, for example, by a forklift. The hose is lightweight and easy to handle. It is primarily designed for unloading milk from tankers. Not recommended for heavy-duty working conditions in process applications. Norms and requirements: 1) General: EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) Food industry, food contact: EC 1935/2004, EC 2023/2006 (GMP). Inner layer compliant with D.M. 21/03/73, FDA 21 CFR 177.2600, BfR, RAL (German Institute for Quality Assurance and Certification). Inner layer: white NR/NBR blend. Reinforcement: synthetic braid, PET spiral. Outer layer: blue synthetic rubber. Working pressure: 16 bar. Vacuum: 0.7 bar. Operating temperature: from -30°C to +85°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and discharge hose intended for the transfer of food substances, requiring the use of odorless and tasteless rubber. It does not contain phthalates and bisphenol A. The inner layer made of NBR/PVC is resistant to standard cleaning agents and processes used in the food industry. Suitable for milk and its derivatives as well as fatty food substances. Widely used in the food industry under standard operating conditions. Norms and requirements: Food industry, contact with food: 1935/2004/EC and 2023/2006/EC (GMP). D.M. 21/03/73, FDA 21 CFR 177.2600, BfR XXI cat. 2. Inner layer: white NBR/PVC rubber. Reinforcement: synthetic braid, steel spiral. Outer layer: blue synthetic rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: from -15°C to +90°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong and very flexible and elastic pressure hose reinforced with two steel braids intended for conveying saturated steam at higher pressure. The inner layer is resistant to high-temperature steam. The outer layer is resistant to high temperature and weather conditions. For steam, use special screw-on fittings designed for steam – precisely matched to the diameter and thickness of the hose. To extend the lifespan, the hose should be emptied of steam after use to avoid the accumulation of condensate. Inner layer: black EPDM rubber. Reinforcement: double steel braid. Outer layer: red micro-perforated EPDM rubber. Working pressure: 18 bar. Operating temperature: from -40°C to +210°C (temporarily up to +230°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction and discharge hose with an inner layer made of chemically resistant ultra-high molecular weight polyethylene (UPE, UHMWPE). The inner layer of UPE is resistant to most aggressive chemicals, antistatic (R<106Ω), compliant with food hose requirements, smooth, with a low friction coefficient during flow, preventing medium deposition on the walls. This significantly facilitates cleaning and allows for use in the cosmetic, pharmaceutical, and food industries. Reinforced with synthetic cord and steel spirals. The outer layer is made of chemically resistant EPDM rubber, antistatic (R<106Ω), abrasion-resistant, ozone-resistant, weather-resistant, and fire-resistant. Compliant with EN 12115:11 type Ω/T requirements, fully antistatic - ensures the dissipation of electrostatic charges through the hose walls (R<109Ω). This enables the use of the hose in explosion hazard zones. The hose is widely used for various applications in the chemical industry. Standards and requirements: Chemical hoses: EN 12115:2011 (type Ω/T). Food industry, contact with food (inner layer): 1935/2004/EC, 2023/2006/EC (GMP), 10/2011/EU (simulated fluids A, B, C, D2). Installation: use smooth fittings with a spigot ("tail" to the hose) without sharp or high ribs that could cut or damage the inner layer of UPE when tightened. The spigot diameter should be precisely matched to the hose diameter to ensure tightness. Installation with clamp sleeves or band clamps. Confirmation of resistance and application conditions requires contact with Tubes International, especially for temperatures above 50°C. Inner layer: black UPE polyethylene. Reinforcement: textile cord, steel spiral. Outer layer: black EPDM rubber. Working pressure: 16 bar. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and discharge hose designed for the transfer of liquid products from the petrochemical industry containing up to 50% aromatic hydrocarbons, fuels, gasoline, diesel, heating oil, lubricating oils, etc. The inner layer is made of black, smooth, antistatic (dissipating electric charges 10^4 Ω < R < 10^9 Ω) NBR rubber. Reinforcement with synthetic cord and steel spirals. The outer layer is made of black NBR rubber, resistant to oil and weather conditions. Relatively low weight and flexible hose construction make it easy to handle, characterized by a wide, universal application for fuel transfer or other compatible media in typical working conditions. Inner layer: black NBR rubber. Reinforcement: synthetic cord, steel spirals. Outer layer: black NBR rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: from -35°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong RIG STAR D discharge hose and RIG STAR SD suction-discharge hose are designed for the transfer and handling of crude oil, petrochemical products, and drilling cuttings mixed with crude oil (up to 50% aromatic compounds). It can also be used for cement, barite, seawater, and brine. The inner layer is made of black, smooth, antistatic NBR rubber. It features a copper wire ensuring electrical continuity between the hose ends. The outer layer is made of CR chloroprene rubber, flame-retardant, resistant to abrasion, ozone, seawater, and weather conditions. Designed as a specialized OFFSHORE hose for operation on drilling platforms. Widely used on North Sea platforms. It can also be successfully used in land applications. Inner layer: black NBR rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black CR rubber. Working pressure: 20 bar. Vacuum: 0.9 bar. Operating temperature: from -30°C to +85°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and discharge hose intended for the transfer of fuels and liquid products from the petrochemical industry, containing up to 50% aromatic compounds, including gasoline, diesel fuel, and mineral oil. It can be used for tankers, storage tanks, loading stations, and industrial equipment. The hose is widely used in industry and transport under standard working conditions. The inner layer is made of smooth, black, antistatic (R <106 Ω/m) NBR rubber. Reinforcement with synthetic cord and steel spiral. It has two copper wires ensuring electrical continuity between the hose ends – provided there is a proper connection to the ends. The outer layer is made of black SBR/NBR rubber, antistatic (R <106 Ω/m), resistant to abrasion, oil, ozone, and weather conditions. Inner layer: black NBR rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black SBR/NBR rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: from -30°C to +85°C (up to +100ºC for oil).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSoft and flexible textile-reinforced suction hose designed for conveying saturated steam. Inner layer with good resistance to high temperature and saturated steam. Outer layer resistant to temperature, abrasion, weather conditions, and ozone. The hose is widely used in the industry for low-pressure saturated steam – for light applications. For steam, use special screw-on fittings designed for steam. To extend the lifespan, the hose should be emptied of steam after use to avoid the accumulation of condensate. Inner layer: black EPDM rubber. Reinforcement: synthetic cord. Outer layer: black micro-perforated EPDM rubber. Working pressure: 6 bar. Operating temperature: from -40°C to +170°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and pressure hose made according to platinum-enhancing technology, resistant to UV and ozone. Compliant with the requirements of 1935/2004 CE, FDA 21 CFR 177.2600, USP class VI, European Pharmacopoeia 3.1.9, BfR XV, Journal Officiel Brochure 1227. At operating temperatures above +100°C, the maximum working pressure stated in the tables should be reduced by 1% for each 1°C increase in temperature. The safety factor is 4:1. Inner layer: translucent silicone. Reinforcement: four polyester braids, steel spiral (AISI 316). Outer layer: translucent silicone. Operating temperature: from -60°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and pressure hose made according to platinum-enhancing technology. The inner layer of the hose is extruded. Compliant with FDA 21 CFR 177.2600, USP Class VI, European Pharmacopoeia 3.1.9, BfR XV, Journal Officiel Brochure 1227, and CE Directive 1935/2004. Maximum vacuum 736.6 mm Hg (0.98 bar). At operating temperatures above +100°C, the maximum working pressure specified in the tables should be reduced by 1% for each 1°C increase in temperature. Inner layer: translucent silicone. Reinforcement: four polyester braids, AISI 316 steel spiral. Outer layer: translucent silicone. Operating temperature: from -60°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality pressure hose manufactured using platinum-enhanced technology. The inner layer of the hose is extruded. Compliant with FDA 21 CFR 177.2600, USP Class VI, European Pharmacopoeia 3.1.9, BfR XV A, Journal Officiel Brochure 1227, and CE Directive 1935/2004. At operating temperatures above +100°C, the maximum working pressure specified in the tables should be reduced by 1% for each 1°C increase in temperature. Inner layer: translucent silicone. Reinforcement: four layers of polyester braiding. Outer layer: translucent silicone. Operating temperature: from -60°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible suction and discharge hose intended for water, juices, beverages, and other food products, reinforced with a hard PVC spiral, which also contributes to the hose's lightweight. Additionally, the impact-resistant spiral ensures good resistance to vacuum and hose kinking. The transparent wall facilitates easy visual monitoring of the medium flow, and the absence of phthalates in the material allows the hose to be used for the transfer of milk and its derivatives, as well as alcohols with a concentration of up to 50%. It is not recommended for oils and fatty food substances. The smooth inner surface reduces flow losses and ensures ease of cleaning. The outer surface is also smooth, facilitating the installation of fittings using tapes or clamps, reducing external damage from abrasion, and aiding in keeping the hose clean. As a hose reinforced only with a hard PVC spiral, lacking a braid, it undergoes certain elongations under pressure, which should be considered in application, especially at temperatures above 40°C. Standards and requirements: Food industry, contact with food: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B, C, and D1), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: hard PVC spiral. Working pressure: from 5 bar to 7 bar, depending on the hose diameter. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible pressure hose for general purposes. Used for air, water, light chemicals, and liquid and semi-liquid food products such as water, juices, beverages, beer, wine, and alcohols with a concentration of up to 50% (and up to 20% for hoses with the index SO-PVCSTAR-CR). Not recommended for food substances containing fats and oils. Suitable for milk and its derivatives (not suitable for milk and dairy products for hoses with the index SO-PVCSTAR-CR). Phthalate-free. Standards and requirements: Food industry, food contact: compliant with European regulations 1935/2004/EC and 10/2011/EU (simulant fluids A, B, C, and D1). For hoses with the index SO-PVCSTAR-CR: 1) General: EU 2015/863 (RoHS 3), EC 1907/2006 (REACH). 2) Food industry, food contact: compliant with European regulations 1935/2004/EC and 10/2011/EU (simulant fluids A, B, and C). Hose material: transparent PVC. Reinforcement: polyester braid. Working pressure: from 8 bar to 22 bar, depending on the hose diameter. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible suction and discharge hose intended for water, juices, beverages, and alcohols with a concentration of up to 50% (and up to 20% for hoses with the SO-PVCSTAR-MS index), and other food products. Not recommended for food substances containing fats and oils. Suitable for milk and its derivatives (however, hoses with the SO-PVCSTAR-MS index are not suitable for milk and dairy products). Reinforcement with a steel wire spiral embedded in the PVC wall provides good resistance to vacuum and hose collapse. The smooth inner surface reduces flow losses and ensures ease of cleaning. The transparent wall allows for easy visual monitoring of flow. In the absence of direct contact with food (in industry, construction, agriculture), it can be used for light chemicals, water, sludges, and wastewater, and other fluids (without fats, oils, and hydrocarbons). As a non-braided hose, it exhibits some elongation under pressure. Standards and requirements: Food industry, food contact: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulants A, B, C, and D1), 2023/2006/EC (GMP). For hoses with the SO-PVCSTAR-MS index: Food industry, food contact: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulants A, B, and C), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: galvanized steel spiral. Working pressure: from 6 bar to 11.5 bar, depending on the hose diameter. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible, bendable, and almost smooth inside hose designed for the extraction and transport of dust, powders, granules, grains, flakes, and similar lightweight materials with abrasive properties. Made from polyether-polyurethane, it has good resistance to abrasion, ozone, weather conditions, hydrolysis, and biological corrosion. Suitable for contact with food for the transport of bulk and liquid food materials, including fatty or oily substances. Not recommended for milk and its derivatives. Reinforcement with a hard PVC spiral provides good crush resistance. The antistatic version of the hose features a copper antistatic wire embedded on the outer side of the hose along the reinforcing spiral. Effective grounding of the wire ensures a sufficient level of electrostatic charge dissipation for many applications. Particularly used in the agri-food industry, plastics, building materials, etc. The WIND STAR PU hose complies with European requirements 10/2011/EU (simulants A, B, C, D2, and E) and American FDA 21 CFR 177.2600 "d", "e", "f" (dry, liquid-water, fatty). Additional information regarding food and pharmaceutical applications – see the section "Hoses for food products." Hose material: transparent polyether-polyurethane. Reinforcement: hard PVC spiral. Operating temperature: from -40°C to +80°C (working pressure dependent on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction hose designed for the transfer and handling of crude oil, petrochemical products, and drilling cuttings mixed with crude oil (up to 50% aromatic compounds). It can also be used for cement, barite, seawater, and brine. The inner layer is made of black, smooth, antistatic NBR rubber. Reinforced with layers of durable synthetic cord. It features a copper wire ensuring electrical continuity between the hose ends. The outer layer is made of CR chloroprene rubber, flame-retardant, resistant to abrasion, ozone, seawater, and weather conditions. Designed as a specialized OFFSHORE hose for operation on drilling platforms. Widely used on North Sea platforms. Can be successfully used in land applications. Inner layer: black NBR rubber. Reinforcement: synthetic cord. Outer layer: black CR rubber. Working pressure: 20 bar. Operating temperature: from -30°C to +85°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose designed for the transfer of liquid products from the petrochemical industry containing up to 50% aromatic hydrocarbons, fuels, gasoline, diesel, heating oil, lubricating oils, etc. Inner layer made of black, smooth NBR rubber. Reinforcement with synthetic cord. It has copper wires ensuring electrical continuity between the hose ends – provided that it is correctly connected to the fittings. Outer layer made of black NBR rubber, resistant to oil and weather conditions. Relatively low weight and flexible hose construction make it easy to handle, characterized by a wide, universal application for fuel transfer or other compatible media under typical working conditions. Inner layer: black NBR rubber. Reinforcement: synthetic cord. Outer layer: black NBR rubber. Working pressure: 10 bar. Operating temperature: from -30°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality hose resistant to most demanding working conditions. Exceptionally flexible, lightweight, and convenient to use. Appropriate wall thickness and braid ensure the retention of the hose's cross-sectional shape. The antistatic inner layer guarantees safety when used in hazardous areas. Designed for medical gases in accordance with EN ISO 5359 standard. Particularly recommended and widely used in hospitals and ambulances. Inner layer: black, antistatic PVC R <106 Ω/m. Reinforcement: polyester braid. Outer layer: PVC in various colors to indicate the hose's intended use for specific types of media - blue (nitrous oxide), white (oxygen), yellow (vacuum), black and white (air). Working pressure: 15 bar. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight, flexible hose designed for the transport of air, oil and fuel vapors, dust, powders, very fine wood shavings, chips, and light bulk materials. Suitable for all types of industry, particularly commonly used for dust extraction and the removal of vapors and fine solid particles in the woodworking, furniture, ceramics, and plastics industries. Highly flexible and very axially compressible, also flexible at low temperatures. Good abrasion resistance, in the AS version made of polyester, also resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. The hose is available in the following versions: P2 PU – version with polyester-polyurethane, with very good abrasion resistance; P2 PU AS – antistatic version (R ≤108 Ω, compliant with TRBS 2153, for extraction also with TRGS 727), made of polyester-polyurethane, with good abrasion resistance, resistant to microbes and hydrolysis. Hose material: transparent polyester-polyurethane (P2 PU), polyester-polyurethane (P2 PU AS). Wall thickness measured between the spiral: 0.4 mm. Reinforcement: spiral made of steel wire. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong industrial suction hose for water and compressed air, designed for operation in harsh conditions in industry, road construction, and even in quarries. Inner layer resistant to oil mist. Abrasion and weather resistant. Widely used and proven in various industrial applications. Hose available in black and yellow. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black SBR rubber. Reinforcement: synthetic cord. Outer layer: black or yellow EPDM rubber. Working pressure: 20 bar. Operating temperature: from -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, semi-transparent, flexible hose made of platinum-cured silicone rubber. Used in the pharmaceutical, cosmetic, and biotechnology industries, medical devices, cell culture, sterile filling lines, water for injection (WFI), chemistry and blood analyzers, and liquid chromatography. Can be used in peristaltic pumps – moderate lifespan. Characterized by an exceptionally smooth inner surface that prevents the deposition and adhesion of contaminants inside the hose and the growth of bacteria. This facilitates complete cleaning and sterilization of the hose. The smooth inner layer also reduces flow resistance through the hose. Low extractability, non-toxicity, non-hemolytic, and non-pyrogenic ensure total fluid purity in sensitive applications. Meets hygiene requirements of US FDA 21 CFR 177.2600, NSF-51, 3-A, and USP Class VI as well as ISO 10993 for contact with blood, bodily fluids, and tissues for up to 30 days. Sterilization possible by steam (30 min, 1 bar, 121°C), ethylene oxide, or radiation (up to 2.5 Mrad). Full roll length of the hose is 15 m. Hose available in inch and metric sizes. Working pressure defined relative to burst pressure with a safety factor of 1:5. Material: silicone (platinum). Maximum operating temperature: +204°C. Brittleness temperature: -80°C. Hardness: 50° Shore (A). Density: 1.14 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality thin-walled BARRIER hose for refrigerant flow in a single polyester braid for use in automotive and industrial air conditioning and refrigeration systems operating on R134a, R1234yf, R404a Suva MP52, and R22 mineral and synthetic oils PAG, POE, and PVE. The outer layer is resistant to abrasion and weather conditions. Standards: SAE J2064 type C class I. Inner layer: black CR rubber separated by a nylon (PA) layer. Reinforcement: polyester braid. Outer layer: black CIIR rubber, micro-perforated. Working pressure: 35 bar. Operating temperature: from -35°C to +125°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction and discharge hose with an inner layer made of chemically resistant polyethylene with ultra-high molecular weight (UPE, UHMWPE), black and white MARBLE type, smooth, antistatic (R<106 Ω). The inner layer is resistant to most acids and bases as well as many other aggressive chemicals (at elevated but not very high temperatures), making the hose widely used in the chemical and petrochemical industries. The MARBLE type UPE inner layer also complies with food hose requirements, features a low friction coefficient during flow, and prevents medium deposition on the walls. This significantly facilitates cleaning and allows for use in the cosmetic, pharmaceutical, and food industries as well. Reinforced with synthetic cord and steel spiral. The outer layer is made of chemically resistant EPDM rubber, antistatic (R < 106 Ω), abrasion-resistant, ozone-resistant, and weather-resistant. Compliant with EN 12115:11 requirements (type Ω/T, fully antistatic (R < 109 Ω) - ensures the dissipation of electrostatic charges through the hose walls, allowing use in all explosion hazard zones. Standards and requirements: Chemical hoses: EN 12115:2011 (type Ω/T). Food industry, contact with food (inner layer): 1935/2004/EC, 2023/2006/EC (GMP), 10/2011/EU, FDA 21 CFR 177.1520 (c), D.M. 21/03/73. Explosive atmospheres: ATEX directive (zones: 0, 1, 2, 20, 21, 22), EN 50014/ IEC 60079-0. Installation: use smooth fittings with a spigot ("tail" to the hose) without sharp or high ribs that could cut or damage the UPE inner layer when tightened. The spigot diameter should be precisely matched to the hose diameter to ensure tightness. Installation with clamp sleeves or band clamps. Inner layer: white-black UPE polyethylene. Confirmation of resistance and application conditions requires contact with Tubes International, especially for temperatures above 50°C. Inner layer: white-black UPE polyethylene. Reinforcement: synthetic cord, steel spiral. Outer layer: black EPDM rubber. Working pressure: from 12 bar to 16 bar - depending on the hose diameter. Operating temperature: from -35°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal, strong, and highly flexible rubber suction hose, designed for air, water, and light chemicals. It can be used for dispersive water-based epoxy and polyurethane paints. Not suitable for oils, fuels, aromatic hydrocarbons, cellulose paints, chloroprene, and others containing aromatic solvents (e.g., toluene, xylene) or gasoline. For chemical applications, we recommend contacting Tubes International. Inner and outer layers are antistatic (R<109 Ω/m), outer layer resistant to ozone, aging, and weather conditions. Inner layer: black EPDM rubber. Reinforcement: textile braid. Outer layer: black EPDM rubber. Working pressure: 20 bar. Operating temperature: from -40°C to +100°C (temporarily +120°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe HYPERLINE FX hose is an optimal solution for industrial applications where high flow rates, chemical and temperature resistance, and permeation resistance are required. It is perfectly suited for the transfer of chemicals, fuels, oils, paints, solvents, adhesives, dyes, gases, and steam, detergents, water, and food substances. At operating temperatures above +160°C, the maximum working pressure specified in the table should be reduced by 1% for each 1°C above this temperature. For example, at a temperature of 180°C, the maximum working pressure for the AF-FXSS-10 hose is: 100 bar – (180°C-160°C) x 1 = 100 bar – 20% = 80 bar. In cases where a substance that is a poor conductor and has potential electrification properties flows through the PTFE hose, the electric charge will accumulate on the inner surface of the PTFE, and to avoid static electricity issues, an antistatic AS variant of PTFE is used. Antistatic Teflon in the AS version contains graphite evenly distributed in the PTFE and has a resistance R <10^8 Ω (according to ISO 8031 annex A). Hose material: smooth inside, corrugated outside PTFE (Teflon) - natural white and antistatic - black. Reinforcement: AISI 304 steel braid. Working pressure: from 50 bar to 110 bar - depending on the hose diameter. Operating temperature: from -70°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, semi-transparent smooth-walled PTFE hose with excellent chemical resistance. Designed for low-pressure installations, chemicals, paints, adhesives, liquid and gaseous fuels, oils, lubricants, air, gases, water, steam, and water-based fluids. Used in all types of industry. The hose is not antistatic (does not dissipate electric charges for non-conductive substances). Not recommended for pneumatic plug connections. Can also be used as mechanical guidance for hoses or rods due to the low friction coefficient and self-lubricating properties of Teflon. Flame retardant (UL94 V-0) and with a high oxygen index (LOI). Safety factor n = 4:1. The burst and working pressure of the hose decreases at operating temperatures above 20°C and is dependent on its height. Hose material: smooth PTFE (Teflon). Shore hardness (D): 58. Operating temperature: from -200°C to +260°C. Working pressure: from 2.3 bar to 10.8 bar - depending on the hose diameter.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure delivery hose, reinforced with steel, designed for conveying superheated steam. The outer layer is resistant to high temperatures and weather conditions. Not intended for steam cleaners ("dry steam cleaners"). For water vapor, use special screw-on fittings designed for water vapor. To extend the lifespan, the hose should be emptied of steam after use to avoid condensate buildup. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black EPDM rubber. Reinforcement: double cord of steel wire. Outer layer: black or red micro-perforated EPDM rubber. Working pressure: 18 bar. Operating temperature: from -40°C to +210°C (temporarily up to +232°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsARMORVIN HNA is a suction and discharge hose designed for the transfer of juices, beverages, milk, water, wine, beer, alcohols with a concentration of up to 50%, and other food products. Not recommended for fatty substances such as oils. Besides food applications, it can be used in industries such as construction and agriculture for light chemicals, dirty water, sludges, sewage, and other fluids that do not contain fats, oils, and hydrocarbons. It is also suitable for air, and the steel spiral embedded in the hose wall allows it to be used for vacuum transfer of powders, granules, and other mildly abrasive bulk materials. When dealing with such substances, wear resistance and potential static electricity issues should be considered. The smooth inner surface reduces flow losses and ensures ease of cleaning. Standards and requirements: Food industry, food contact: compliant with European regulations 1935/2004/EC and 10/2011/EU (simulative fluids A, B, C, and D1), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: galvanized steel spiral. Working pressure: from 2 bar to 7 bar - depending on the hose diameter. Vacuum at 20°C: from 0.7 bar to 0.85 bar - depending on the hose diameter. Operating temperature: from -5°C to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible and elastic, easy to operate suction and discharge hose designed for the transfer of fatty and non-fatty food substances, requiring the use of odorless and tasteless rubber. It contains no plasticizers, phthalates, or animal-derived substances. The inner layer made of NBR is resistant to standard cleaning agents and processes used in the food industry. The outer layer is resistant to temporary contact with animal and vegetable fats. Particularly recommended for applications requiring a small bending radius with good pressure and vacuum resistance. Widely used in the dairy industry and for the transfer of milk under normal operating conditions. Not recommended for transfer applications in heavy working conditions and under pulsating pressure. Standards and requirements: 1) General: EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) Food industry, contact with food: EC 1935/2004, EC 2023/2006 (GMP). Inner layer compliant with D.M. 21/03/73, FDA 21 CFR 177.2600, BfR, 3A Sanitary Standards, RAL (German Institute for Quality Assurance and Certification). Inner layer: white NBR rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: blue synthetic rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: from -20°C to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, transparent, soft, and flexible hose for laboratory and food applications. Ideal for analytical devices, condensers, incubators, desiccators, as gas and drainage lines. Suitable for food and biopharmaceutical products. Also commonly used for cooling computer processors. The glassy smooth, pore-free inner surface prevents the deposition and adherence of contaminants inside the hose and facilitates cleaning. Complete repeatability of hose parameters across all batches. Can be used with peristaltic pumps, but lifespan is limited. The hose is free from phthalates and BPA (Bisphenol A). Meets hygiene and food contact requirements: European 1935/2004/EC and 10/2011 EU (for conditions and substances according to certification), American FDA, NSF-51, 3-A, USP Class VI, Japanese #370/1959. Sterilization possible by steam, ethylene oxide, or radiation. Compliant with REACH and California Proposition 65 – does not contain hazardous and prohibited substances. Full roll length of the hose is 15 m. Available VACUUM version with thicker walls for vacuum applications. The specified working pressure is defined relative to the burst pressure with a safety factor of 1:5. Material: PVC (special). Maximum operating temperature: up to +74°C. Brittleness temperature: -46°C. Hardness: 56° Shore (A). Density: 1.21 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality BARRIER type refrigerant hose (thick-walled) designed for automotive and industrial cooling and air conditioning systems operating on R134a, R12, R404a Suva MP52, and R22 refrigerants with mineral and synthetic oils PAG, POE, and PVE. The outer layer is resistant to oil, abrasion, and weather conditions. Standards: SAE J2064 type C class II. Inner layer: black CR rubber, nylon (PA) layer. Reinforcement: two polyester braids. Outer layer: black EPDM rubber, micro-perforated. Working pressure: from 17 bar to 24 bar, depending on hose diameter. Operating temperature: from -30°C to +125°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong and flexible suction-discharge hose made of PVC intended for water and sewage. Smooth inner wall, slightly corrugated on the outside. Good resistance to external impacts and harsher operating conditions. Flexible at low temperatures. Used in irrigation systems, tankers, and vacuum trucks, for sewer cleaning and septic tank emptying. Hose material: green PVC. Reinforcement: hard PVC spiral. Working pressure: from 1.8 bar to 4.5 bar - depending on the hose diameter and temperature. Operating temperature: from -25°C to +55°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMedium thickness flexible hose with reinforcing spiral, designed for suction and transport of bulk abrasive materials, granules, chips, shavings, etc. Used in various industrial sectors, particularly often employed for the removal of solid particles in the plastics, wood, construction materials, and metal industries. Flexible and elastic, even at low temperatures. Smooth inside, low compressibility. Dense and thick steel spiral coated with white PVC ensures high pressure parameters, is corrosion-resistant, and has good adhesion to the hose material. Hose with good abrasion resistance, also resistant to oils and gasoline. Installation on couplings with bridge clamps (right-handed). Other diameters may be available on special order. Versions: P3 PU – standard version, made of polyester-polyurethane, highly abrasion-resistant; P3 PU AS – antistatic version (R ≤108 Ω), compliant with TRBS 2153 and for suction also with TRGS 727, made of polyether-polyurethane, with good abrasion resistance, resistant to microbes and hydrolysis; P3 PU EL – electrically conductive version (R ≤104 Ω), compliant with ATEX 2014/34/EU, TRBS 2153 and for suction also with TRGS 727, can be used in explosion hazard zones after risk assessment, made of black polyether-polyurethane, with good abrasion resistance, resistant to microbes and hydrolysis. Hose material: transparent polyester-polyurethane (P3 PU), transparent polyether-polyurethane (P3 PU AS), black polyether-polyurethane (P3 PU EL). Wall thickness measured between the spiral: 0.8 ÷ 1.5 mm (depending on hose diameter). Reinforcement: spiral made of steel wire coated with white PVC. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible welding hose for oxygen made according to ISO 3821 standards. It is characterized by resistance to kinks and weather conditions. Not recommended for gases produced from fuels, oils, and LPG gas. Inner layer: black SBR/NR rubber. Reinforcement: synthetic braid. Outer layer: blue smooth SBR/NR rubber. Working pressure: 20 bar. Operating temperature: from -20°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal, lightweight, highly flexible suction and discharge hose designed for general industrial applications for water and light chemicals, other liquids (excluding fats, oils, and hydrocarbons). It can also be used for air, vacuum transfer of dust and powders – abrasion resistance and potential static electricity issues should be considered. It can be used (at temperatures up to +40°C) for liquid and semi-liquid food products such as juices, beverages, beer, wine, alcohols up to 50% concentration, milk, and dairy products. It is not recommended for oils and fatty food substances. The reinforcement with a steel wire spiral embedded in a soft PVC wall provides good resistance to vacuum and hose collapse. The transparent wall allows for easy visual monitoring of flow. As a hose reinforced only with a steel spiral (without a braid), it exhibits some elongation under pressure, which should be taken into account in applications, especially at elevated temperatures. The METALFLEX PVC hose complies with European regulations 1935/2004/EC, 10/2011/EU (simulants A, B, C, and D1), 2023/2006/EC (GMP), and FDA CFR 21 175.300 and 175.1210. It is suitable for temporary contact with food during the transfer of food substances - under the conditions specified in the manufacturer's declaration of conformity (available from Tubes International). Hose material: transparent, soft PVC. Reinforcement: galvanized steel spiral. Working pressure for a temperature of 20°C: from 1 bar to 9 bar - depending on the hose diameter. As the operating temperature increases, the working pressure value of the hose decreases. Operating temperature: from -10°C to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe version of the HYPERLINE hose without a braid (Tube Only) is externally spiral corrugated (right-handed) and internally smooth. The hose combines the advantages of a flexible corrugated hose and a smooth-walled hose with undisturbed flow. The standard version is made of natural, semi-transparent PTFE, allowing for visual flow monitoring. The antistatic AS version made of carbon-filled Teflon (black) ensures the dissipation and dispersion of electric charges for substances and conditions at risk of static electricity. The hose material meets FDA requirements (21 CFR 177.1550 for the standard hose, 21 CFR 178.3297 for the antistatic version). It is flame-retardant (UL94 V-0) and has a high oxygen index (LOI). It can be used for the transfer of chemicals, foodstuffs, fuels, oils, paints, solvents, adhesives, dyes, and detergents under very low pressure conditions. Ends can be fitted with crimped stainless steel tube sleeves. The relationship between working pressure and temperature for the HYPERLINE FX Teflon hose without a braid applies only up to a temperature of 150°C. Above this temperature, there is a decrease in working pressure and vacuum. If the hose is to be used above these temperatures, this must be taken into account, and appropriate tests should be conducted under operating conditions. Available versions: standard and antistatic. Hose material: PTFE (Teflon). Operating temperature: from -70°C to +150°C (up to +260°C - working pressure of the hose dependent on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe HYPERLINE SB (HYDRAFLON) hose features an inner layer made of high-quality seamless PTFE, ensuring minimal porosity, maximum flexibility, and resistance to vibrations. The braid is made from heat-treated AISI 304 stainless steel wire with a tensile strength of 1700 MPa. It is used for the transmission of chemicals, food substances, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam, etc. - as well as for classic high-pressure hydraulic oil installations. The HYPERLINE SB hose is a version of the SMOOTHBORE hose with a medium wall thickness and an internal diameter adapted to standard hydraulic fittings; installation is done using standard straight clamp jaws. In cases where static electricity hazards are identified (risk of charge generation and accumulation), HYPERLINE SB hoses in the antistatic AS version should be used. The antistatic Teflon in the AS version is black (contains appropriately dispersed graphite in PTFE) and has a resistance R <10^8 Ω (according to ISO 8031 annex A). This ensures the dissipation and dispersion of electric charges. At operating temperatures above +130°C, the maximum working pressure should be reduced by 0.75% for each 1°C increase in temperature. The value "Wall thickness [mm]" provided in the Technical Data refers to the PTFE layer. Hose material: smooth PTFE (Teflon). Reinforcement: single braid of AISI 304 steel. Working pressure: from 80 bar to 350 bar - depending on the hose diameter. Operating temperature: from -70°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose for cleaning and washing installations and machines in the food industry with steam and hot water. The inner layer meets FDA 21 CFR 177.2600 and BfR XXI category 2 requirements. The outer layer is resistant to vegetable and animal fats. High-quality hose, commonly used for cleaning and washing with hot water or steam in the food industry (e.g., dairies, meat industry). Note: the hose should not be used simultaneously for water and steam. For steam, use special screw-on fittings designed for steam. To extend the lifespan, the hose should be emptied of steam after use to avoid condensation buildup. Standard roll length: 60 m (or 120 m - contact Tubes International). Inner layer: white butyl rubber. Reinforcement: synthetic cord. Outer layer: blue NBR/PVC rubber. Working pressure: 6 bar (10 bar - for water). Safety factor: 10:1 (3:1 - for water). Operating temperature: from -30°C to +165°C (from -30°C to +95°C - for water).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose for propane-butane and natural gas. Meets the requirements of ISO 3821 standard. Inner layer: black NBR rubber. Reinforcement: two textile braids. Outer layer: orange EPDM/SBR rubber. Working pressure: 20 bar. Operating temperature: from -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality large-diameter refrigerant hose designed for automotive (especially trucks and buses) and industrial refrigeration and air conditioning systems operating on R 134a and R404a refrigerants, as well as mineral and synthetic oils PAG and POE. The outer layer is resistant to oil, abrasion, high temperatures, and weather conditions. Standards: SAE J2064 type B (dimensions SAE 100R5). Installation: use special screwed or clamped fittings. Inner layer: black IIR rubber. Reinforcement: steel braid. Outer layer: black CSM rubber, micro-perforated. Working pressure: 35 bar. Operating temperature: from -40°C to +125°C.
