Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight and flexible hose intended for discharge air, dust, dusts, sawdust, fine chips, light bulk materials etc. Specially designed according to the requirements of the wood and furniture industry, it can also be used in other industries. Antistatic and flame-retardant, it ensures a high level of work safety. pliable and flexible, also in low temperatures. less compressible than hose SMARTFLEX® 0.4, ale smoother inside. With very good abrasion resistance, also resistant to microbes and hydrolysis. Contains no halogen compounds or plasticisers. Resistant to oils and petrol. The optimal flow direction of the medium is marked with an arrow. The hose wall thickness is measured between the spiral. Assembly on connectors with bridge clamps (prawo-handed). Other diameters may be available on special order. Anti-electrostatic properties: permanently antistatic (in accordance with ISO 8031 resistance R 9 Ω, in accordance with the German technical regulations TRGS 727 (6.4.2.4) specific resistance R 8 Ωm, in accordance with directive 2014/34/EU (ATEX) it can be used in specified explosion-hazard zones - which should be preceded by a risk analysis). After effective two-sided earthing of the spiral, it can be treated as electrically conductive – in accordance with BGI 739-2 recommendations. Flame-retardant – in accordance with DIN 4102 class B1. Hose material: transparent polyether-polyurethane. Wall thickness measured between the spiral: 0.6 mm. Reinforcement: spiral with wire steel. Operating temperature: od -40°C up to +100°C (momentarily up to +125°C).- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh quality, flexible hose in color cream, designed specially for industry pharmaceutical, biotechnology and laboratories. has high resistance fatigue, exceptionally high service life in use in pump peristaltic and good resistance na flaking („spallation” - crumbling microparticles material hose in result pressure rotor pump). is characterized also very low permeability for media gas, low level absorption conveyed products, good resistance na acids, bases and oxidation. ideal for use in processes diagnostics, sampling and culture cultures cellular in vitro, production vaccines, for bioreactors, sterile lines filling, processes fermentation, extraction and purification (purification). opaque wall hose protects sensitive products against radiation UV. hose is compliant with requirements USP Class VI and is completely nie cytotoxic, nie hemolytic and nie pyrogenic. compliant with ISO 10993 for contact with blood, fluids body and tissues for 30 dni. meets requirements NSF-51 for contact with food. possible multiple sterilization steam in autoclaves (30 min, 1 bar, 121°C), cleaning CIP and SIP installations, oxide ethylene or radiation (gamma Cobalt 60 for 5 Mrad). resistant na flame (UL 94-HB). length full roll hose 7.5 m. pressure working determined relative to pressure bursting at factor safety 1:5. Material: thermoplastic elastomer (TPE). temperature use: from -51°C to +135°C. temperature brittleness: -75°C. Hardness: 64° Shore (A). Density: 0.98 g/cm³. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose delivery, very flexible, resistant na aging, ozone, conditions weather and abrasion. intended for air, water and light chemicals: non-oxidizing, diluted acids (np. hydrochloric and sulfuric), diluted bases, solutions salts, alcohols, acetone, ketones, coolants na base glycols. Nie is suitable for oils, fuels, carbon aromatic. can be used for various paints water-soluble and na base ketones and esters. Nie is suitable for paints cellulose, chlorinated-rubber and other containing solvents aromatic (np. toluene, xylene) or gasoline. Layer inner and outer antistatic R 6 Ω in accordance with EN ISO 8031:2009. Inner layer: black rubber EPDM. Reinforcement: single or double (DN 32÷38) braid textile spiral. Outer layer: black rubber EPDM. temperature use: from -40°C to +120°C (momentarily up to +140°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose suction-delivery intended for conveying water industrial, sewage, sludge, liquids non-corrosive etc. light, pliable, resistant to kinking and vacuum. Layer outer resistant to ozone and conditions atmospheric. used commonly for pumps in industry, construction and agriculture. assembly – depending on the diameter and type fittings using straps, clamps, ferrule clamping, bands. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black rubber SBR. Reinforcement: cord synthetic, steel spiral. Outer layer: black rubber SBR. Working pressure: from 5 bar to 10 bar, depending on the diameter hose. Vacuum: 0.9 bar. Operating temperature: od -30°C up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, semi-transparent hose smooth with PTFE o excellent resistance chemical. intended for low-pressure installations chemicals, paints, fuels, oils, greases, air, gases, water, steam and liquids na base water – we all types industry. as inert chemical and free of components, which could penetrate for medium internal, can be used for substances food. compliant with FDA 21 CFR 177.1550, EU 10/2011, EC 1935/2004 and Italian D.M. 174 06/04/2004. The hose is not antistatic (it does not dissipate electric charges for non-conductive substances). Not recommended for pneumatic push-in fittings. can be used also as mechanical guiding cables or tie rods of regard na low factor friction and self-lubricating properties PTFE. Flame-retardant (UL94 V-0) and with a high oxygen index (LOI). factor safety n = 3:1. pressure bursting and working hose, decreases in temperature use above 20°C and is dependent od jej the height. Material hose: PTFE (teflon). temperature use: from -60°C to +260°C. pressure working: from 3 bar to 56 bar - depending on diameter and wall thickness wall hose.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible pressure hose, PVC general purpose and for products food. used for compressed air, water, liquids cooling based on water, light chemicals and liquid and semi-liquid products food. smooth wall inner reduces losses flow and ensures ease cleaning. W industry food It can be used for conveying food hydrated, acidic, alcohols for 20% np. juices, drinks, beer, wine, (simulants A, B, C; up to +40°C and 0.5 h). Not recommended for milk and dairy products or food substances containing fats and oils. hose RAGNO CR complies with the European requirements 1978/142/EEC, 1935/2004/EC, 1895/2005/EC and 10/2011/EU (simulants A, B, C), 2023/2006/EC (GMP). Suitable for temporary contact with food when conveying food substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International). Inner layer: transparent PVC. Reinforcement: a polyester braid. Outer layer: transparent PVC. Working pressure at a temperature of 20°C: from 8 bar to 20 bar - depending on the diameter hose. The working pressure value decreases as the temperature rises. Operating temperature: from -5°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBlack flexible hose A universal o exceptional resistance na aging, conditions weather and ozone, o sound resistance chemical. resistant na temperature in wide the scope from -60°C to +135°C. extremely flexible, flexible, o high resistance fatigue na deformation, resistant na abrasion. excellent for use in pumps peristaltic. used for conveying and dosing in industry and services np. for dispensing soaps and agents disinfectant, agents cleaning, soda caustic, chemicals for etching and electroplating, in systems washing glass and glass panes itp. soft Material hose (61° Shore (A)) is very flexible and ensures excellent service life for 1000 hours use in pump peristaltic. hose is alternative for used often hoses with traditional mixtures rubber such jak EPDM, chloroprene. It has good chemical resistance to a range of chemical substances, especially acids and bases, oxidizing agents jak np. water oxidized, hypochlorite sodium czy ozone (300 pphm). resistant na range fats animal and vegetable. Not recommended for hydrocarbons. resistant na aging and radiation UV. is characterized low permeability for gases in comparison with hoses rubber. possible is connection hose through welding. version VACUUM o thick walls Intended is for continuous use with vacuum and is resistant na cracking and aging. Length of a full hose roll 15 m. pressure working determined relative to pressure bursting at factor safety 1:5. Material: norprene® - thermoplastic elastomer (TPE). Maximum operating temperature: +135°C. temperature brittleness: -60°C. Hardness: 61° Shore (A). Density: 0.98 g/cm 3. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsIndustrial hose for cold and hot water for heavy conditions use, demanding high flexibility, resistance to abrasion, conditions atmospheric and ozone. used m.in. for cooling and temperature control moulds injection. It can be used for air. use for temperatures above +95°C reduces service life hose. Not is resistant to oil, not recommended also for air with mist oil. recommended assembly rings or ferrules clamping. Inner layer: black EPDM rubber. Reinforcement: a synthetic braid. Outer layer: black, blue or red EPDM rubber. Working pressure: 20 bar. Operating temperature: od -30°C up to +95°C (20 bar), od -30°C up to +140°C (10 bar), momentarily up to +160°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose intended for industrial systems refrigerant (alternative for copper tubes) and air conditioning automotive (only for function filling and testing). W particular for freons (R22, R134a, R404a, R407c, R410a, R507) and oils compressor type POE and PAG. hose in sizes od 1/12" for 1/4" can be also used for conveying CO 2 (R-744) - use CO 2 as the medium refrigerant requires pressures about 10 times greater than in case conventional freons. Inner layer: polyamide (PA), for diameters od 1/12" for 1/4" blend PA with TPE (elastomer thermoplastic). Reinforcement: a polyester braid. Outer layer: micro-perforated, resistant to abrasion, polyurethane. Working pressure: from 45 bar to 120 bar, depending on the diameter hose. Operating temperature: od -45°C up to +130°C (for water and air up to +70°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose suction-delivery intended for conveying many substances chemical, mainly for solutions acids, bases, ketones, formaldehydes, alcohols industrial and glycols. often used in plants industrial for discharge contaminants water and water process. appropriate also for water sea. Layer inner and outer antistatic R≤10 6 Ω/m. Available version delivery (without spiral steel) - hose ORLANDO. Vacuum: 0.9 bar. Inner layer: black rubber EPM (EPR). Reinforcement: synthetic cord, steel spiral. Outer layer: black rubber EPM (EPR). pressure working: 10 bar. temperature use: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, very flexible and pliable hose intended for discharge aggressive chemical vapours and for use in elevated temperature. good resistance to temperature, good resistance to vapours acids and solvents. resistant also on radiation UV, ozone, hydrolysis and corrosion biological. strength on bending. used for mechanical extraction vapours, air conditioning and ventilation in vehicles mechanical (buses, cars and trailers camping, boats recreational etc.), on inlets air for engines and compressors, in dryers granulates and plastics, in blow-moulding machines film etc. Other diameters are available on special order in the scope 15 ÷ 800 mm. version flame-retardant P2SP SE is compliant with requirements standards DIN 4102 B1 for materials construction. Hose material: fabric polyester impregnated black TPE (thermoplastic elastomer). Wall thickness: 0.4 mm. Reinforcement: spiral with wire steel. Operating temperature: od -40°C up to +150°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight transparent smooth hose with natural (non-regenerated) polymer fluorine FEP (fluorinated ethylene propylene), material o properties close for PTFE. hose is characterized excellent chemical resistance, stability temperature dimensions and shape, smooth surface inner and external. good transparency hose allows na easy observation level or flow liquid. resistant na radiation UV. intended for low-pressure installations aggressive substances chemical or when required is high cleanliness and inert chemical material hose. used commonly in laboratories, industry chemical and pharmaceutical. Ze regard na excellent properties insulating used in industry electronic and semiconductors. The hose is not antistatic (it does not dissipate electric charges for non-conductive substances). Not recommended for pneumatic push-in fittings. Flame-retardant (UL94 V-0) and with a high oxygen index (LOI). factor safety n = 4:1. Material hose: FEP. hardness Shore (D) 55. temperature use: from -200°C to +206°C. pressure working: od 4.25 bar up to 13 bar - depending on diameter hose.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, resistant to kinking and action conditions atmospheric hose welding for acetylene made acc. to standards ISO 3821. Not recommended for gases generated based on fuels, oils and propane - butane (LPG). Inner layer: black rubber SBR/NR. Reinforcement: a synthetic braid. Outer layer: smooth red rubber SBR/NR. Working pressure: 20 bar. Operating temperature: od -20°C up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong and flexible hose suction-delivery with completely made with resistant to abrasion polyurethane o high resistance to fats and oils. hose not contains phthalates and It can be used in industry food for conveying liquid and dry substances food. includes to: - in particular fats and oils food np. olive oil (simulant D2, up to +40°C and 30 min); - milk and its dairy products, drinks milk (simulant D1, up to +40°C and 30 min); - food hydrated, acidic, alcohol for 20 % and dry (simulants A, B, C, E; up to +70°C and 1 h). W use not involving direct contact with food (in industry, construction, agriculture) It can be used for water, light chemicals and other liquids based on fat and oils industrial (should take into account resistance chemical). used also for air, vacuum conveying dusts, powders, granulates and other abrasive substances bulk (should then take into account abrasion resistance and any problem electricity static). very smooth surface inner reduces losses conveying and ensures ease cleaning. transparent wall allows on visual control of the flow. Reinforcement dense spiral with wire steel ensures very good resistance to vacuum and kinking hose. made hose with polyurethane in comparison with similar hoses, PVC results considerably greater resistance on abrasion, greater strength (pressure working and vacuum) and greater range temperature at slightly smaller flexible. hose ARMORVIN TOTAL PU OIL TPHF complies with the European requirements 1935/2004/EC, 1895/2005/EC and 10/2011/EU (simulants A, B, C, D1, D2, E), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 (d). Suitable for temporary contact with food when conveying food substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International). Hose material: transparent polyurethane. Reinforcement: galvanised steel spiral. Working pressure at a temperature of 20°C: from 3 bar to 7 bar - depending on the diameter hose. Operating temperature: from -40°C to +90°C, temperature medium, working pressure depends on temperature. As the working temperature rises, the hose's working pressure value decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose HYPERLINE V (VISIFLON) made is with high quality PTFE serrated spirally, ensuring exceptional among hoses PTFE flexible, flexibility and resistance na vibration. Jak each hose PTFE, Due to the unique properties of PTFE (large operating temperature range, resistance to most substances and chemical compounds, negligible adhesion surface), hose VISIFLON perfectly is suitable for conveying substances chemical, food, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam water itp. W case when identified is hazard electricity static (danger formation and accumulation charges electric, should use hoses VISIFLON made with PTFE antistatic – version antistatic AS. antistatic teflon is black (contains appropriate distributed in PTFE graphite) and has resistance R 8 Ω (in accordance with the standard ISO 8031 anex A). ensures to discharge and dissipation (dissipation) charges electric. selection hose in version standard with natural PTFE or in version antistatic should confirm in Tubes International. braid in version SS made is with annealed wire of steel stainless AISI 304 and ensures high strength pressure. at temperature use above +130°C maximum pressure working should reduced o 1% na each 1°C rise temperatures. available versions layer internal: standard (natural white) and antistatic (black). Material hose: spirally Serrated PTFE (teflon). Reinforcement: braid of steel AISI 304. pressure working: from 20 bar to 60 bar - depending on diameter hose. temperature use: from -70°C to +230°C. resistant na full vacuum for temperatures: +130°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThick, strong and flexible hose delivery compliant with dimensions and requirements standards EN ISO 6134:2005 type 2 class A (Ω), of reinforcement steel, intended for conducting steam saturated and superheated. Layer inner o sound resistance na high temperature and steam saturated. can be used momentarily for steam superheated o temperature 232°C and pressure 18 bar, longer use with steam superheated reduces service life hose. Layer outer resistant na temperature, conditions atmospheric, abrasion and aging. antistatic R ≤10 6 Ω. hose used in industry chemical, petrochemical, power and in other use industrial. Not intended for steam cleaners ("dry steam cleaners"). For water steam, use special fittings bolted with screws, intended for water steam. To extend the service life, the hose should be emptied of steam after use, to avoid condensate accumulation. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black rubber EPDM. Reinforcement: double steel wire cord. Outer layer: black rubber EPDM, micro-perforated. pressure working: 18 bar. temperature use: from -40°C to +210°C (momentarily up to +232°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery flexible and at the same time light hose suction-delivery intended for water, juices, drinks, alcohols with a concentration up to 20% and other products food. not advisable for greasy substances such as milk czy oils. resistant to vacuum and kinking thanks to embedded spiral with wire steel in wall hose. high advantage its is both transparent wall resistant to radiation UV, allowing on easy visual control of the flow media, as well as smooth jej internal parts reducing losses flow and ensuring ease cleaning. W ratio for hose ARMORVIN HNA is characterized greater pressure working and greater resistance on vacuum. W use not regarding direct contact with food (in industry, construction, agriculture) It can be used: 1) for light chemicals, water, sludge and sewage, other liquids (without fat, oils and hydrocarbons); 2) for air, vacuum conveying dusts, powders, granulates and other lightly abrasive substances bulk (not greasy). In that case the abrasiveness and the possible problem of static electricity must be taken into account. as hose reinforced spiral steel (without braid) is characterized a certain elongation under pressure, co should take into account in use, especially in elevated temperatures. Standards and requirements: Food industry, food contact: compliant with the European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B and C), 2023/2006/EC (GMP). Hose material: light green transparent PVC. Reinforcement: galvanised steel spiral. Working pressure: from 2 bar to 8 bar, depending on the diameter hose. Operating temperature: from -5°C to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight hose smooth with PTFE o excellent resistance chemical in various versions color. made with high quality PTFE with addition dye (Material compliant with FDA). Flame-retardant (UL94 V-0) and with a high oxygen index (LOI). use for high quality fittings push-in is possible. factor safety n=4:1. pressure bursting and working hose, decreases in temperature use above 20°C and is dependent od jej the height. Material: PTFE (teflon), colored. hardness Shore (D): 60. pressure working: od 5.5 up to 20 bar. temperature use: from -200°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible hose medium wall thickness, intended for discharge dust, sawdust, chips, bulk materials, granulate etc. Dla all types industry, in particular often used for discharge chips and other particles solid in industry wood, furniture, ceramic, plastics. dense spiral reinforcing ensures greater resistance to vacuum in ratio for hoses ECO 0.4 and ECO 0.6. pliable, less compressible, smooth inside and flexible - also in low temperatures. O sound resistance to abrasion, resistant also on microbes and hydrolysis. Not toxic, Contains no halogen compounds or plasticisers. Resistant to oils and petrol. hose marked is an arrow indicating correct direction flow medium. The hose wall thickness is measured between the spiral. Assembly on connectors with bridge clamps (prawo-handed). Other diameters may be available on special order. hose Available is in following versions: ECO – version standard, ECO SE – version with material flame-retardant (UL94 V-2), ECO AS – version permanently antistatic ISO 8031: R 9 Ω, TRGS 727 (6.4.2.4): R 8 Ωm, directive 2014/34/EU (ATEX): It can be used in defined zones hazard explosion po analysis risk, ECO SE AS – version antistatic and flame-retardant (Available on special order). hose ECO produced is in process production compliant with with policy sustainable growth in which uses raw materials originating with recycling pure waste with process production, energy renewable, closed circulation water and other innovation. Hose material: transparent polyether-polyurethane. Reinforcement: spiral with wire steel. Wall thickness measured between the spiral: 0.7 mm. Operating temperature: od -40°C up to +100°C (momentarily for + 125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCream - beige flexible hose free of smell and taste, non-toxic. resistant na temperature in the scope od - 60°C up to +135°C. extremely flexible, flexible, o high resistance fatigue na deformation, resistant na abrasion. excellent for use in pumps peristaltic. used for dispensing and portioning cold and hot products food, for soaps, detergents and agents disinfecting, for paints and toners, pesticides and fertilizers and in laboratories. soft Material hose (61° Shore-A) is very flexible and ensures excellent service life for 1000 hours use in pump peristaltic. hose is alternative for used often hoses, PVC or silicone. It has good chemical resistance to a range of chemical substances, especially acids and bases, oxidizing agents jak np. water oxidized, hypochlorite sodium czy ozone. resistant na range fats animal and vegetable. Not recommended for hydrocarbons. resistant na aging and radiation UV. meets requirements FDA 21 CFR 177.2600 for contact with food. possible multiple sterilization steam in autoclaves, cleaning CIP and SIP in installations, oxide ethylene or method radiation. length full roll hose: 15 m. Material: TPE (Norprene® – thermoplastic elastomer). Maximum operating temperature: up to +135°C. temperature brittleness: -60°C. Hardness: 61° Shore (A). Density: 0.98 g/cm³. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe highest quality hose suction-delivery „FULL OHM” completely antistatic (Ω/T), intended for conveying substances highly flammable and very aggressive chemical. Layer inner with polymer perfluoroalkoxy PFA (polymer fluorine o properties close for PTFE), antistatic (R 6 Ω), mirror smooth, meeting high requirements hygienic (FDA, USP, European EU). layer intermediate with rubber synthetic, contain Reinforcement with cord synthetic and spiral with wire steel. outer Layer type MARBLE (marbled), smooth, coated polyethylene (UPE), antistatic (R 6 Ω), meeting requirements FDA, free of smell and taste, resistant na abrasion, ozone and aging, chemicals and short-term operation aggressive acids. advantage layer MARBLE is also low factor friction - hose slides and nie soils surface with which is in contact, is easy for cleaning. excellent resistance chemical PFA and properties antistatic both layer internal jak and outer (R 6 Ω) and in across wall hose (R 9 Ω) make, that hose is costly, ale technically ideal solution for applications demanding highest safety, we all zones hazard explosion (ATEX). used in industry chemical, petrochemical, pharmaceutical and cosmetic, a also in biotechnology. Nie is intended for sterilization in autoclave. Na special order Available version with additional built-in cables copper (M/T). standards and requirements: hoses chemical: EN 12115:2011. industry food, contact with food: 1935/2004/EC, 2023/2006/EC (GMP); Inner layer: 10/2011/EU, USP Class VI, FDA 21 CFR 177.1550; ISO 10993-4,-10,-11, nie cytotoxic (ISO 10993 Part 5); Outer layer: FDA 21 CFR 177.1520. Nie contains plasticizers, phthalates ani substances origin animal. atmospheres explosive: directive ATEX (zones: 0, 1, 2, 20, 21, 22), EN 50014/ IEC 60079-0. Confirmation of resistance and application conditions requires contact with Tubes International. assembly: should use fitting with a spigot („tail” for hose) smooth, not having sharp or high notches, which could po crimping cut or damage layer inner with PFA. The spigot diameter should be precisely matched to the hose diameter to ensure tightness. Assembly with clamping ferrules or shell clamps. Inner layer: black polymer PFA. Reinforcement: synthetic cord, steel spiral. Outer layer: white-black polyethylene UPE, rubber synthetic. pressure working: 10 bar. Vacuum: 0.9 bar. temperature use: from -35°C to +130°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong hose delivery intended for water cooling in smelters, foundries and we all use, where hose rubber works close source heat. coated fiber glass resistant to temperature up to +530°C caused radiation thermal. used in systems cooling. especially recommended for installation water at furnaces metallurgical. resistant to momentary action splashes red-hot hot metal. non-conductive – resistance electrical blend rubber ≥108 Ω/m. Inner layer: white insulating EPDM rubber. Reinforcement: cord synthetic. Outer layer: EPDM rubber coated fiber glass. Working pressure: 20 bar. Operating temperature: od -40°C up to +120°C (outer up to +530°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose delivery intended for conveying LPG (molten and gas) and gas natural. Layer outer resistant to action ozone and conditions atmospheric. antistatic (R 6 Ω/m). It has a copper wire ensuring electrical continuity between the hose ends. made in accordance with the standard EN 1762:2018, type D. Inner layer: black synthetic rubber. Reinforcement: a synthetic braid. Outer layer: black micro-perforated synthetic rubber. Working pressure: 25 bar. Operating temperature: od -30°C up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe highest quality hose suction-delivery intended for conveying wine, beer, juices fruit etc. substances food free of fats, requiring the use of rubber free of odour and taste. Contains no phthalates or bisphenol A. Designed for high-class wines and alcohols, for use in breweries and distilleries. Widely used in the spirits industry for conveying strong alcohols with a concentration up to 96%. It has copper wires ensuring electrical continuity between the hose ends, which increases the safety of conveying high-proof, flammable alcohol (during assembly, contact of the wire with the end must be ensured). Layer outer resistant to abrasion, aging and conditions atmospheric. standards and requirements : industry food, contact with food 1935/2004/EC, 2023/2006/EC (GMP). Layer inner compliant with FDA 21 CFR 177.2600, BfR XXI kat.2, D.M. 21/03/73. Inner layer: white rubber butyl (IIR). Reinforcement: cord synthetic, steel spiral. Outer layer: red rubber butyl (IIR). Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: from -40°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery light and flexible hose suction-delivery for agriculture, industry food and applications universal. intended water, light chemicals, sludge and sewage, agents protection plants, other liquids (without fat, oils and hydrocarbons). also for air, vacuum conveying dusts, powders, granulates and other lightly abrasive substances bulk (non-greasy). In that case the abrasiveness and the possible problem of static electricity must be taken into account. W industry food It can be used for conveying food hydrated, acidic, alcohols for 20% np. juices, drinks, beer, wine, (simulants A, B, C; up to +40°C). Not recommended for milk and dairy products or food substances containing fats and oils. Reinforcement with a rigid-PVC spiral, impact-resistant, provides good resistance to vacuum and kinking of the hose. The outer surface is corrugated, smooth inside. hose AGROFLEX LD complies with the European requirements 1935/2004/EC, 10/2011/EU (simulants A, B, C), 2023/2006/EC (GMP). Suitable for temporary contact with food when conveying food substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International). Hose material: green transparent PVC. Reinforcement: white rigid-PVC spiral. Working pressure at a temperature of 20°C: from 2 bar to 6 bar. As the working temperature rises, the hose's working pressure value decreases. Operating temperature: from -10°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe hose is made of a smooth, seamless PTFE tube. The PTFE tube of the hose is extruded under strictly defined and controlled conditions, which ensures its highest quality, minimal porosity and maximum possible for obtaining for hose smooth with PTFE flexible and flexibility. braid made is with annealed wire of steel stainless AISI 304 o high strength na stretching 1700 N/mm 2, o strictly controlled angle arrangement and voltage bundles wire braid, co results minimal changes length hose pod high pressure. Due to the unique properties of PTFE (large operating temperature range, resistance to most substances and chemical compounds, negligible adhesion surface) hose SMOOTHBORE perfectly is suitable for conveying substances chemical, food, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam water itp. - as well as for classic high-pressure hydraulic oil installations. W case when identified is hazard electricity static (danger formation and accumulation charges electric), should use hoses SMOOTHBORE made with PTFE antistatic – version antistatic AS. antistatic teflon version AS is black (contains appropriate distributed in PTFE carbon) and has resistance R 8 Ω (in accordance with the standard ISO 8031 anex A). ensures to discharge and dissipation (dissipation) charges electric. Safety factor 3:1; if a factor of 4:1 is required (np. acc. to EN 16643) should multiply values through 0.75. at temperature use above +130°C maximum pressure working given in parameters should reduced o 0.75% na each 1°C above tej temperatures. for example at temperature 170ºC maximum pressure working for hose AF-SWSB-06 is: 240 bar – (170°C-130°C) x 0.75 = 240 bar – 30% = 168 bar. The value "Wall thickness" given in the Technical data refers to the PTFE layer. Material hose: smooth PTFE (teflon). Reinforcement: single braid of steel AISI 304. pressure working: from 55 bar to 240 bar - depending on diameter hose. temperature use: from -70°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUnreinforced and very flexible hose with transparent PVC intended for pressureless (or under very low pressure) conveying water, beer, wine, alcohols with a concentration up to 20%, juices, drinks, other liquids food. Not is recommended for milk and products milk and for oils and greasy substances food. used also for liquids in use general-industrial, for light chemicals (e.g. diluted acids and bases) and as A guard pipes, lines, cables etc. For the hose, the stated pressure value is the approximate value of the recommended working pressure, assumed for a typical PVC hose, at a safety factor of 5:1. Use of the hose at a specific working pressure should be preceded by a test under operating conditions. Standards and requirements: Food industry, food contact: compliant with the European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B and C), 2023/2006/EC (GMP). Hose material: transparent PVC. Working pressure: low, up to a few bar, depends on temperature. Operating temperature: from -5°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsWidely used for washing hot water floors and equipment industrial. is suitable also for use external. resistant to conditions atmospheric and abrasion. Not is resistant to oil, not recommended also for air with mist oil. W comparison with a hose "Tubes 2116" has thicker wall. Inner layer: white EPDM rubber. Reinforcement: a polyester braid. Outer layer: red or blue EPDM rubber micro-perforated. Working pressure: 10 bar. Operating temperature: od -40°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCream, flexible hose chemical o multilayer the structure designed specially, to connect resistance chemical with high service life in pump peristaltic. smooth Layer inner o very sound resistance chemical, free of plasticizers, resistant na acids, bases, salts, alcohols and ketones, o low absorption and adsorption liquids na base water. Layer outer with thermoplastic elastomer (Norprene®) ensures excellent properties and high service life at use in pump peristaltic. hose meets requirements hygienic and for contact with food: American FDA 21 CFR 177.1520 and is resistant na most agents cleaning and disinfecting. sterilization steam, oxide ethylene or radiation. perfectly is suitable for dosing soaps and detergents, agents washing and for rinsing vessels. used for production and dosing various chemicals we all fields industry. Length of a full hose roll 15 m. The given working pressure is determined relative to the bursting pressure at a safety factor of 1:5. Material: polyolefin / TPE (Norprene® - thermoplastic elastomer). temperature use: from -60°C to +74°C. temperature brittleness: -60°C. Hardness: 61° Shore (A). Density: 0.98 g/cm³. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, very pliable and flexible hose intended for extraction hot vapours, fumes, gases, air blowing and discharge air cooling. reinforced version hose SILICONE 1, o two layers fabric coated silicone and spiral steel placed between layers. resistant chemical, on radiation UV and aging. used m.in. for extraction gases in industry metallurgical, foundry, industry glass and ceramic, for hot air in dryers industrial, in printing houses and paper mills, in vehicles and engines for air cooling, incineration plants, a also for extraction exhaust gases and gases welding. smooth inside (in state extended), o very small radius bends enabling easy installations in tight spaces equipment and vehicles. not recommended for continuous dynamic bending. Assembly with clamps. Other diameters are available on special order. Hose material: two fabric glass coated red silicone. Reinforcement: spiral with wire steel, double outer cable with fibre glass. Operating temperature: od -70°C up to +250°C (momentarily up to +300°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose o smooth surface internal intended for compressed air, water, light chemicals, agents fungicidal, fertilisers and pesticides. commonly used in agriculture for sprinkling, irrigation, spraying. Layer outer resistant to abrasion and conditions atmospheric. Inner layer: black PVC. Reinforcement: a polyester braid (double polyester braid for version REFITTEX 80 BAR). Outer layer: black PVC. Working pressure at a temperature of 20°C: 20 bar (white stripe), 40 bar (blue stripe), 80 bar for diameter internal 13 mm, above 50 bar (red stripe). As the working temperature rises, the hose's working pressure value decreases. Operating temperature: from -20°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDouble hose welding for oxygen and acetylene. made according to standards ISO 3821. Inner layer: black synthetic rubber. Reinforcement: double polyester braid. Outer layer: smooth synthetic rubber in color red (acetylene) and blue (oxygen). Working pressure: 20 bar. Operating temperature: od -32°C up to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFree of braid version TO (Tube Only) hose VISIFLON, made with high quality PTFE serrated spirally (clockwise) ensuring exceptional among hoses PTFE flexible, flexibility and resistance na vibration. hose VISIFLON TO can be used for conveying substances chemical, food, fuels, oils, paints, solvents, adhesives, dyes, detergents in conditions very low pressure. standard version VISIFLON TO made is with natural, semi-transparent PTFE, co allows visual control flow. version antistatic VISIFLON TO AS with PTFE with addition carbon (black) ensures discharge and dissipation charges electric for substances and conditions hazard electricity static. Material hose meets requirements FDA (21 CFR 177.1550 for VISIFLON TO, 21 CFR 178.3297 for VISIFLON TO AS). Flame-retardant (UL94 V-0) and with a high oxygen index (LOI). assembly hose requires straightening notches na length tail fitting, made na special equipment. fitting can be mounted then through crimping ferrules tube of steel stainless. value pressure working for hose PTFE VISIFLON without braid, applies only for temperatures 100°C, a in case vacuum for temperatures 80°C. above these temperatures occurs drop pressure working and vacuum. assuming use hose above these temperatures should to take into account and carry out appropriate test in conditions use. Material hose: spirally Serrated PTFE (teflon). temperature use: from -70°C to +100°C (up to +230°C). pressure working: from 2 bar to 4 bar - depending on diameter hose.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe hose is made of a smooth, seamless PTFE tube. The PTFE tube of the hose is extruded under strictly defined and controlled conditions, which ensures its highest quality, minimal porosity and maximum possible for obtaining for hose smooth with PTFE flexible and flexibility. version thick-walled HW recommended is for heavier conditions use, gases (up to 100 bar) and for applications in which available cyclic changing temperatures use. braid made is with annealed wire of steel stainless AISI 304 o high strength na stretching 1700 N/mm 2, o strictly controlled angle arrangement and voltage bundles wire braid, co results minimal changes length hose pod high pressure. Due to the unique properties of PTFE (large operating temperature range, resistance to most substances and chemical compounds, negligible adhesion surface) hose SMOOTHBORE perfectly is suitable for conveying substances chemical, food, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam water itp. - as well as for classic high-pressure hydraulic oil installations. W case when identified is hazard electricity static (danger formation and accumulation charges electric), should use hoses SMOOTHBORE made with PTFE antistatic – version antistatic AS. antistatic teflon version AS is black (contains appropriate distributed in PTFE carbon) and has resistance R 8 Ω (in accordance with the standard ISO 8031 anex A). ensures to discharge and dissipation (dissipation) charges electric. Safety factor 3:1; if a factor of 4:1 is required (np. acc. to EN 16643) should multiply values through 0.75. at temperature use above +130°C maximum pressure working given in parameters should reduced o 0.75% na each 1°C above tej temperatures. for example at temperature 170°C maximum pressure working for hose AF-HWSB-06 is: 260 bar – (170°C-130°C) x 0.75 = 260 bar – 30% = 182 bar. The value "Wall thickness" given in the Technical data refers to the PTFE layer. Material hose: smooth PTFE (teflon). Reinforcement: single braid of steel AISI 304. pressure working: from 55 bar to 240 bar - depending on diameter hose. temperature use: from -70°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose delivery intended specially for conveying AdBlue ® (AUS32, DEF) - 32.5% water solution urea. layer inner hose constitutes black, smooth, antistatic (R‹10 6 Ω/m) rubber EPDM vulcanized without content sulfur. Layer inner hose nie is contaminants additives aluminum, calcium, chlorine, copper, iron, potassium, magnesium, sodium, nickel and zinc, co guarantees retention the highest cleanliness medium in accordance with the standard ISO 22241-2. is to particularly important in industry automotive, in which AdBlue ® fully role regulator in order to decomposition in catalyst SCR harmful for environment oxides nitrogen. its use allows na meeting European standards emissions exhaust EURO 4, 5 and 6. liquid AdBlue ®, to was effective, must be very pure, co forces use specialized hoses, tanks and fittings resistant na AdBlue® and non-contaminating go. fitting and fittings for AdBlue ® should be made of steel stainless or appropriate plastic. except for automotive, hose used is also in industry chemical, na example at production fertilizers nitric. Inner layer: black rubber EPDM. Reinforcement: braid synthetic. Outer layer: black rubber EPDM. pressure working: 10 bar or 20 bar. temperature use: from -40°C to +100°C (momentarily up to +120°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose delivery intended for conducting steam saturated, o sound resistance na high temperature, abrasion and ozone. on request Available hose acc. to standards EN ISO 6134:2005 type 1 class A. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black rubber EPDM. Reinforcement: synthetic cord. Outer layer: black rubber EPDM. pressure working: 6 bar. temperature use: from -40°C to +165°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThick, strong hose intended for lances oxygen in industry metallurgical. Layer outer self-extinguishing made in accordance with the standard ASTM C 542. Inner layer: black rubber CR. Reinforcement: double cord textile, spacer with fibre glass. Outer layer: yellow or blue rubber CR. Working pressure: 30 bar. Operating temperature: od -30°C up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMedium wall thickness, flexible hose intended for discharge dusts, sawdust, chips, offcuts, light bulk materials etc. Specially designed according to the requirements of the wood and furniture industry, it can also be used in other industries. compliant with the standard DIN 26057 Type 2. Antistatic and flame-retardant, it ensures a high level of work safety. less pliable and compressible than SMARTFLEX® 0.4 and 0.6, za to smooth inside, flexible also in low temperatures. With very good abrasion resistance, also resistant to microbes and hydrolysis. Contains no halogen compounds or plasticisers. Resistant to oils and petrol. The optimal flow direction of the medium is marked with an arrow. The hose wall thickness is measured between the spiral. Assembly on connectors with bridge clamps (prawo-handed). Other diameters may be available on special order. Anti-electrostatic properties: permanently antistatic (in accordance with ISO 8031 resistance R 9 Ω, in accordance with the German technical regulations TRGS 727 (6.4.2.4) specific resistance R 8 Ωm, in accordance with directive 2014/34/EU (ATEX) it can be used in specified explosion-hazard zones - which should be preceded by a risk analysis). After effective two-sided earthing of the spiral, it can be treated as electrically conductive – in accordance with BGI 739-2 recommendations. Flame-retardant – in accordance with DIN 4102 class B1. Hose material: transparent polyether-polyurethane. Wall thickness measured between the spiral: 0.7 mm. Reinforcement: spiral with wire steel. Operating temperature: od -40°C up to +100°C (momentarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong hose suction - delivery intended for conveying substances food, requiring the use of rubber free of odour and taste. Contains no phthalates or bisphenol A. thanks to reinforcement spiral steel, has good resistance to vacuum. Suitable for milk and dairy products, as well as wine, beer, fruit juices. not recommended for oils and greasy substances food. Widely used in industry food. Layer outer hose resistant to abrasion and conditions atmospheric. Standards and requirements: Food industry, food contact: 1935/2004/EC and 2023/2006/EC (GMP). D.M. 21/03/73, FDA 21 CFR 177.2600, BfR XXI kat. 2. Inner layer: white rubber natural (NR). Reinforcement: cord synthetic, steel spiral. Outer layer: blue EPDM rubber. Working pressure: 6 bar. Operating temperature: from -25°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose delivery intended for hot water mixed with fluids anti-freeze. used in systems cooling and heating, for pumps in engines and machines. Layer inner resistant to heat and fluids cooling. Layer outer resistant to heat and aging. made in accordance with the standard DIN 73411:79. Roll length: 60 m or 120 m. Inner layer: black EPDM rubber. Reinforcement: cord synthetic. Outer layer: black EPDM rubber. Working pressure: from 2 bar to 4 bar - depending on the diameter hose. Operating temperature: od -40°C up to +120°C.
