Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug cap TEMA 100 protecting against dirt and damage. Material: PVC or carbon steel.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe plug cap for CAMLOCK SAFETY BUMP connectors is an alternative solution to traditional CAMLOCK connector caps, due to its specially designed handle that facilitates hose operation. It is used in the chemical and petrochemical industries. It is made in an antistatic version in black from composite material reinforced with fiberglass.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug cap for ANFOR lever connector. Material: galvanized steel. Working pressure: from 5 bar to 19 bar (depending on connector size). Operating temperature: from -20°C to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug cap for BAUER lever connector. Material: carbon steel, galvanized. Sealing: NR/SBR. Working pressure: 20 bar (up to size 89 mm), 12 bar (for sizes above 89 mm). Operating temperature: from -20°C to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBlind plug intended for the FERRARI lever connector, type F.5B, used among others in agriculture, horticulture, industry, construction, road and tunnel construction, groundwater drainage, wastewater treatment, sewage disposal, environmental protection. Material: carbon steel, galvanized. Sealing: NR-SBR rubber. Operating temperature: from -20°C to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug cap for LAUX 42 lever connector. Material: AISI 316 steel. Sealing: EPDM. Maximum working pressure: 12.5 bar (for liquids), 8 bar (for air).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug cap for LAUX 42 lever connector. Material: carbon steel, galvanized. Sealing: EPDM. Maximum working pressure: 12.5 bar (for liquids), 8 bar (for air).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsGUILLEMIN connector cap with chain. It has a symmetrical design of the connection part. Manufactured according to standard EN 14420-8/NF-E-29572. Material: aluminum. Working pressure: 16 bar. Sealing: white NBR rubber. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsGUILLEMIN connector cap with chain. It has a symmetrical design of the connection part. Manufactured according to standard EN 14420-8/NF-E-29572. Material: AISI 316 steel. Working pressure: 16 bar. Sealing: black FKM-VITON rubber. Operating temperature: from -10°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBlind plug for ROTTA ROTH connector with chain. It has a symmetrical design of the connection part. Material: bronze. Working pressure: 10 bar. Sealing: NBR rubber. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSMS connector cap (Sweden) with chain. It has a symmetrical design of the connection part. Material: bronze. Working pressure: 10 bar. Sealing: NBR rubber. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / Details2" valve for pallet container made entirely of durable polypropylene, eliminating any corrosion. The valve is additionally equipped with a locking latch and a cap. Lever in blue color. Valve outlet connection: GZ S60x6. Material: polypropylene. Sealing: none. Operating temperature: from -10°C to +70°C (temporarily up to +80°C).
- Select options This product has multiple variants. The options may be chosen on the product page / Details2" valve for pallet container made entirely of durable polypropylene, eliminating any occurrence of corrosion. Standardly equipped with an EPDM seal. The valve is additionally equipped with a lever lock (in the form of a screw) and a two-part cap. Lever in red color. Valve outlet connection: GZ S60x6. Material: polypropylene. Sealing: EPDM. Operating temperature: from -10°C to +70°C (temporarily up to +80°C).
- Select options This product has multiple variants. The options may be chosen on the product page / Details2" valve for pallet container made entirely of durable polypropylene, eliminating any occurrence of corrosion. Standardly equipped with a PTFE seal. The valve is additionally equipped with a lever lock (in the form of a screw) and a two-part cap. Lever in red color. Valve outlet connection: GZ S60x6. Material: polypropylene. Sealing: PTFE. Operating temperature: from -10°C to +70°C (temporarily up to +80°C).
- Select options This product has multiple variants. The options may be chosen on the product page / Details2" valve for pallet container made entirely of durable polypropylene, eliminating any occurrence of corrosion. Standardly equipped with a Viton (FKM) seal. The valve is additionally equipped with a lever lock (in the form of a screw) and a two-part cap. Lever in blue color. Valve outlet connection: GZ S60x6. Material: polypropylene. Sealing: Viton (FKM). Operating temperature: from -10°C to +70°C (temporarily up to +80°C).
- Select options This product has multiple variants. The options may be chosen on the product page / Details2" valve for pallet container made entirely of durable polypropylene, eliminating any occurrence of corrosion. Standardly equipped with a PTFE seal. The valve is additionally equipped with a lever lock (in the form of a screw) and a cap. Lever in yellow color. Valve outlet connection: GZ 2" NPT. Material: polypropylene. Sealing: PTFE. Operating temperature: from -10°C to +70°C (temporarily up to +80°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMRF N/C throttling and check valve for direct mounting in actuator connections, used in pneumatic systems for regulating the flow rate of compressed air and the direction of flow. Equipped with a plug-in coupling for easy disassembly of pneumatic hoses. Adjustment change via a control knob and/or screwdriver; possibility of securing the setting with a locking nut. The specified nominal flow at a pressure of 6.3 bar (in the throttled direction). Operating pressure: up to 10 bar. Operating temperature: from -10°C to +70°C. Body material: nickel-plated brass.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThrottle-return valve type MRF/C for direct mounting in actuator connections, used in pneumatic systems for regulating the flow rate of compressed air and the direction of flow. Equipped with a plug connection for easy disassembly of pneumatic hoses. Adjustment change using a screwdriver. The specified nominal flow at a pressure of 6.3 bar (in the throttled direction). Body material: nickel-plated brass. Working pressure: up to 10 bar. Operating temperature: from -10°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThrottle-return valve type MRF/V for installation in the connections of distribution valves, used in pneumatic systems to regulate the flow rate of compressed air and the direction of flow. Equipped with a plug-in coupling for easy disassembly of pneumatic hoses. Adjustment change using a screwdriver. The specified nominal flow at a pressure of 6.3 bar (in the throttled direction). Working pressure: up to 10 bar. Operating temperature: from -10°C to +70°C. Body material: nickel-plated brass.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThrottle-return valve type MRF PTC series PUSH-LOCK for direct mounting in actuator connections, used in pneumatic systems for regulating the flow rate of compressed air and the direction of flow. Equipped with a plug-in coupling for easy disassembly of pneumatic hoses. Adjustment change via a knob with PUSH-LOCK lock. Size: 1/8″, 1/4″. Working pressure: up to 10 bar. Operating temperature: from -10°C to +50°C. Material: plastic.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThrottle valve type MRF OMB series COMPACT "O" used for simultaneous flow regulation in both directions - during filling and venting, applied in pneumatic systems for regulating the flow rate of compressed air. Equipped with a plug-in connection for easy disassembly of pneumatic hoses. Adjustment change using a screwdriver, with the possibility of mounting a protective cover. Size: M5, 1/8″, 1/4″, 3/8″, 1/2″. Working pressure: up to 10 bar. Operating temperature: from -10°C to +70°C. Material: nickel-plated brass.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThrottle valve type MRF/B used for simultaneous flow regulation in both directions - during filling and venting, used in pneumatic systems to regulate the flow rate of compressed air. Equipped with a plug connection for easy disassembly of pneumatic hoses. Adjustment change using a screwdriver. The specified nominal flow at a pressure of 6.3 bar (in the throttled direction). Working pressure: up to 10 bar. Operating temperature: from -10°C to +70°C. Body material: nickel-plated brass.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMRF T/B type throttling valve used for simultaneous flow regulation in both directions - during filling and venting, applied in pneumatic systems to regulate the flow rate of compressed air. Equipped with a plug-in connection for easy disassembly of pneumatic hoses. Adjustment change using a screwdriver. The specified nominal flow at a pressure of 6.3 bar (in the throttled direction). Working pressure: up to 10 bar. Operating temperature: from -10°C to +70°C. Body material: plastic.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTwo-way ball valve with external metric threads, designed for high-pressure hydraulic systems. Equipped with mounting holes. Used in hydraulic systems as a stroke limiting element for actuators. A hose connected to the piston rod or the element moved by the actuator is attached to the lever hole. Upon reaching the stroke, the valve shuts off the oil supply to the actuator. A simple and economical solution used, for example, in self-dumping trailers in agriculture. Material: steel (body, ball, stem). Seals: POM (ball), NBR (stem). Operating temperature: from -40°C to +100°C (POM); from -20°C to +100°C (NBR).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe soft start valve is used to fill the working system with compressed air, operating in a two-stage manner. The application of a control signal causes the shut-off valve to open and air to flow through the throttling valve. Once the output pressure reaches approximately 40 to 60% of the supply pressure, the valve is overridden, allowing air to flow through the full cross-section from the inlet to the outlet. Removing the control signal causes the supply valve to close and the working system to vent. The soft start valve is used in installations where there is a need to protect powered actuators from sudden aeration, which can generate shock loads affecting the structural elements of machines. Excessive air intake from the outlet during the initial aeration of the working system can disrupt the operation of the valve, preventing it from fully opening. Size: SY1, SY2. Connection: BSP 1/8" to 1". Supply pressure: 3 - 10 bar. Additional outlet connection: BSP 1/8" for size SY1, BSP 1/4" for size SY2, at the front and rear. Operating temperature: from -10°C to +50°C. Nominal flow: depending on size from 1250 l/min to 4800 l/min (at pressure 6.3 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBrass mushroom valve with STORZ type fire connection at the outlet (connection made of aluminum or brass, white NBR seal) used as basic equipment for fire hydrant cabinets (fire protection systems, residential buildings, etc.). Connection to the installation with external thread (from 1" to 2.1/2"). Working pressure: 16 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality two-way ball valve type SKH L/S with external metric thread, DIN 2353, designed for high-pressure hydraulic installations. Material: steel (body, ball, stem). Seals: POM (ball), NBR (stem). Operating temperature: from -40°C to +100°C (POM); from -20°C to +100°C (NBR).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThree-way ball valve "L" type RK3L with internal BSP thread, designed for high-pressure hydraulic and industrial installations. For proper selection of the valve for media other than hydraulic oil and for high operating temperatures, consultation with Tubes International is required. Material: stainless steel AISI 316Ti (body, ball, stem). Seals: POM or PTFE (ball), FKM (stem). Operating temperature: from -40°C to +100°C (POM); from -200°C to +250°C (PTFE); from -20°C to +200°C (FKM).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThree-way ball valve "L" type SK3L with internal NPT thread, designed for high-pressure hydraulic installations. Material: steel (body, ball, stem). Seals: POM (ball), NBR (stem). Operating temperature: from -40°C to +100°C (POM); from -20°C to +100°C (NBR).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure needle valve designed for installation in a system or panel mounting. It features a compact design with a relatively high flow rate. Standardly with a V-type stem (valve operation close - open). Each valve is factory tested. The valve has a special design allowing for panel mounting without the need to disassemble the needle, thus not voiding the Manufacturer's warranty. Connection material: AISI 316 steel. Stem material: AISI 316 steel. Valve sealing: metal/metal (AISI 316 steel). Packing seal: PTFE. Operating temperature: up to +230°C. Working pressure: up to 345 bar. Connection: inch LET-LOK®.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsNeedle valve with a non-rotating stem tip (PEEK), designed for installation from the external thread side in HSSC sampling cylinders. The safety insert screwed into the valve protects the cylinder from excessive pressure increase. The safety plate welded to the insert ruptures at a specified pressure, allowing the medium to flow through holes in the hexagonal head of the insert. The safety insert can be easily replaced in the field without the need to disassemble the valve from the cylinder. The valve is tested at 120% of the working pressure according to ISO 14246 (valve with safety insert at 80% of the insert's burst pressure). The valve meets the requirements of the TPED directive (2010/35/EU). Material: AISI 316 steel (knob - aluminum). Safety plate material: alloy 600/B168. Stem sealing: NBR o-ring, PTFE ring. Insert sealing: o-ring (viton). Stem tip: PEEK. Working pressure: up to 206 bar (at 37°), temperature dependent. Insert burst pressure: 131 bar or 196 bar. Flow coefficient: 0.53 Cv. Operating temperature: from -20°C to +122°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCompact, two-piece medium-pressure ball valve designed for demanding general applications. It can be used for precision instrumentation in the chemical, petrochemical, pharmaceutical, energy, and process engineering industries - for liquids and gases. Intended for pipeline installation. The valve features a large size range to ensure sufficiently high flow, sealing integrity (permissible internal leakage through the ball seal 0.1 Ncm³/min), high durability, and low torque. Designed for operation in fully open or fully closed positions. Each valve is pressure tested with nitrogen. Certified according to ISO 15848-1:2006 (E). Body material: AISI 316 steel. Ball and stem material: AISI 316 steel. Lever material: AISI 304 steel, PVC. Ball seal: modified PTFE. Stem seal: PTFE. Operating temperature: from -42°C to +204°C. Working pressure: up to 137 bar (depending on temperature). Connection: GZ NPT.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThree-piece medium-pressure ball valve designed for demanding applications and precision instrumentation for the chemical, petrochemical, pharmaceutical, energy, and process engineering industries - for liquids and gases. Intended for pipeline installation. The valve features a large size range to ensure sufficiently high flow, tight shut-off (permissible internal leakage through the ball seal 0.1 Ncm³/min), high durability, and low torque. Each valve is pressure tested with nitrogen. Certified according to ISO 15848-1:2006 (E). The valve lever with a lock is standardly yellow, with oval-shaped levers available. Body material: AISI 316 steel (ASTM A351 CF8M, casting). Connection material: AISI 316 steel (ASTM A351 CF3M, casting). Ball and stem material: AISI 316 steel. Lever material: AISI 304 steel, PVC. Ball seal: PTFE (standard); versions with different sealing materials with higher parameters available (modified PTFE, PTFE with stainless steel powder, UHMWPE, PEEK). Stem seal: MG1241 (PTFE with fiberglass and graphite) / PTFE (standard). Working pressure (dependent on temperature/sealing material - see chart): up to 103 bar (PTFE). Operating temperature (dependent on sealing material - see chart): up to +186°C (PTFE). Connection: GW BSPT. NOTES! Ball valves are designed to operate in either fully open or fully closed positions. The valves have factory-adjusted packing seals for a pressure of 70 bar. Due to varying operating conditions, periodic adjustment of the stem seal may be required using the stem sealing screw (after removing the lever). Preliminary adjustment is recommended before commissioning the installation.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThree-piece medium-pressure ball valve designed for demanding applications and precision instrumentation for the chemical, petrochemical, pharmaceutical, energy, and process engineering industries - for liquids and gases. Intended for pipeline installation. The valve features a large size range to ensure sufficiently high flow, tight shut-off (permissible internal leakage through the ball seal 0.1 Ncm³/min), high durability, and low torque. Each valve is pressure tested with nitrogen. Certified according to ISO 15848-1:2006 (E). The valve lever with a lock is standardly yellow, with oval-shaped levers available. Body material: AISI 316 steel (ASTM A351 CF8M, casting). Connection material: AISI 316 steel (ASTM A351 CF3M, casting). Ball and stem material: AISI 316 steel. Lever material: AISI 304 steel, PVC. Ball seal: PTFE (standard); versions with different sealing materials with higher parameters available (modified PTFE, PTFE with stainless steel powder, UHMWPE, PEEK). Stem seal: MG1241 (PTFE with fiberglass and graphite) / PTFE (standard). Working pressure (dependent on temperature/sealing material - see chart): up to 103 bar (PTFE). Operating temperature (dependent on sealing material - see chart): up to +186°C (PTFE). Connection: GW NPT. NOTES! Ball valves are designed to operate in a fully open or fully closed position. The valves have factory-adjusted packing seal for a pressure of 70 bar. Due to varying operating conditions, periodic adjustment of the stem seal may be required using the stem sealing screw (after removing the lever). Preliminary adjustment is recommended before starting the installation.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThree-piece medium-pressure ball valve designed for demanding applications and precision instrumentation for the chemical, petrochemical, pharmaceutical, energy, and process engineering industries - for liquids and gases. Intended for pipeline installation. The valve features a large size range to ensure sufficiently high flow, tight shut-off (permissible internal leakage through the ball seal 0.1 Ncm³/min), high durability, and low torque. Each valve is pressure tested with nitrogen. Certified according to ISO 15848-1:2006 (E). The valve lever with a lock is standardly yellow, with oval-shaped levers available. Body material: AISI 316 steel (ASTM A351 CF8M, casting). Connection material: AISI 316 steel (ASTM A351 CF3M, casting). Ball and stem material: AISI 316 steel. Lever material: AISI 304 steel, PVC. Ball seal: PTFE (standard); versions with different sealing materials with higher parameters available (modified PTFE, PTFE with stainless steel powder, UHMWPE, PEEK). Stem seal: MG1241 (PTFE with fiberglass and graphite) / PTFE (standard). Working pressure (dependent on temperature/sealing material - see chart): up to 103 bar (PTFE). Operating temperature (dependent on sealing material - see chart): up to +186°C (PTFE). Connection: inch LET-LOK®. NOTES! Ball valves are designed to operate in either fully open or fully closed positions. The valves have factory-adjusted packing seals for a pressure of 70 bar. Due to varying operating conditions, periodic adjustment of the stem seal may be required using the stem sealing screw (after removing the lever). Preliminary adjustment is recommended before starting the installation.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThree-piece medium-pressure ball valve designed for demanding applications and precision instrumentation for the chemical, petrochemical, pharmaceutical, energy, and process engineering industries - for liquids and gases. Intended for pipeline installation. The valve features a large size range to ensure sufficiently high flow, tight shut-off (permissible internal leakage through the ball seal 0.1 Ncm³/min), high durability, and low torque. Each valve is pressure tested with nitrogen. Certified according to ISO 15848-1:2006 (E). The valve lever with a lock is standardly yellow, with oval-shaped levers available. Body material: AISI 316 steel (ASTM A351 CF8M, casting). Connection material: AISI 316 steel (ASTM A351 CF3M, casting). Ball and stem material: AISI 316 steel. Lever material: AISI 304 steel, PVC. Ball seal: PTFE (standard); versions with different sealing materials with higher parameters available (modified PTFE, PTFE with stainless steel powder, UHMWPE, PEEK). Stem seal: MG1241 (PTFE with fiberglass and graphite) / PTFE (standard). Working pressure (dependent on temperature/sealing material - see chart): up to 103 bar (PTFE). Operating temperature (dependent on sealing material - see chart): up to +186°C (PTFE). Connection: metric LET-LOK®. NOTES! Ball valves are designed to operate in either fully open or fully closed positions. The valves have factory-adjusted packing seals for a pressure of 70 bar. Due to varying operating conditions, periodic adjustment of the stem seal may be required using the stem sealing screw (after removing the lever). Preliminary adjustment is recommended before starting the installation.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal ball valve type 7224 with full bore, intended for gas installations, in pressure class MOP 5. Complies with the requirements of the PED directive 2014/68/EU and 2009/142/EC, in accordance with standard EN 331 + A1. Body material: nickel-plated brass. Ball material: chrome-plated brass. Lever material: aluminum. Ball sealing: PTFE. Stem sealing: FKM + NBR. Connection: BSP/Gas BSPT. Operating temperature: from -20°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBall valve for compressed air, intended for pneumatic hammers. Working pressure: 25 bar. Body material: galvanized carbon steel. Ball material: chrome-plated brass. Lever material: galvanized carbon steel. Ball sealing: PTFE. Operating temperature: from -20°C to +100°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsBall valve for compressed air and water. Body material: galvanized carbon steel. Ball material: chrome-plated brass. Ball sealing: PTFE. Inlet with internal thread, outlet with external thread or with cast iron claw connections with a pitch of 42 mm, with rubber (NBR) or brass sealing. Lever with end stop. Equipped with venting. Working pressure: 10 bar. Operating temperature: from -20°C to +100°C. Robust, maintenance-free design. Used in compressors and construction and industrial equipment.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality high-pressure two-way ball valve designed for precision instrumentation for the chemical, petrochemical, pharmaceutical, energy, and process engineering industries - for liquids and gases. Intended for pipe or panel mounting. The valve features high sealing integrity (permissible internal leakage through the ball seal 0.1 Ncm³/min), high durability, and low torque. Each valve is pressure tested with nitrogen. Certified according to ISO 15848-1:2006 (E). Pneumatic actuated valves available. Available in two pressure versions: with a maximum working pressure of 206 bar and 413 bar, respectively. Body material: AISI 316 steel (ASTM A351 CF8M, casting) - for the 206 bar version; AISI 316 steel (ASTM A-276, forging) - for the 413 bar version. For the low-pressure version (206 bar), a brass option is available. Ball material: AISI 316 steel. Lever material: nylon, brass insert; standard lever color is black (other colors available, metal lever, lever with padlock ISLT). Ball and stem sealing: modified PTFE (PCTFE, PEEK option). Working pressure (dependent on temperature/seal material - see chart): up to 206 bar (modified PTFE). Operating temperature (dependent on seal material - see chart): from -34°C to +210°C (modified PTFE). Connection: GW NPT. NOTES! Ball valves are designed to operate in either fully open or fully closed positions. The valves have factory-adjusted packing seals for a pressure of 70 bar. Due to varying operating conditions, periodic adjustment of the stem sealing may be required using the stem sealing screw (after removing the lever). Preliminary adjustment is recommended before commissioning the installation by tightening the sealing screw by 1/8 to 1/4 turn.
