Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, transparent, flexible hose completely free of plasticizers for chemical and food applications - requiring high chemical resistance due to the nature of the substances (e.g., wine - alcohol, acids - orange juice) or used cleaning and disinfecting agents. Resistant to acids, bases, salts, alcohols, and ketones, with very low levels of absorption and adsorption. This minimizes the risk of changing the properties, taste, and smell of the fluid even with repeated use of the hose. The glassy smooth, pore-free inner surface prevents the deposition and adherence of contaminants inside the hose and facilitates cleaning. Resistant to chemical cleaning and disinfecting agents. Not recommended for hydrocarbons. Meets hygiene and food contact requirements: European 1935/2004/EC and 10/2011 EU (for conditions and substances according to certification), American FDA 21 CFR 177.1520, NSF-51. Possible sterilization with ethylene oxide or radiation (up to 2.5 Mrad). Compliant with REACH - does not contain hazardous and prohibited substances. Proper incineration of used hoses does not release hazardous substances (e.g., hydrochloric acid). The hose is used for both food substances (e.g., wine dispensing) and chemical applications: detergent installations, ink dispensing, acid filling for batteries, chemical analyzers. Full hose roll length 15 m (for internal diameter 25.4 mm - 7.5 m). The specified working pressure is defined relative to the burst pressure with a safety factor of 1:5. Material: polyolefin. Operating temperature: from -75°C to +54°C. Brittleness temperature: -75°C. Hardness: 75° Shore (A). Density: 0.90 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose designed for air, water, and other media. Characterized by flame resistance and resistance to welding sparks and hot metal shavings. Resistant to hydrolysis, biological corrosion, UV radiation, solvents, and detergents. Withstands a vacuum of 0.9 bar. Calibrated outer diameter allows compatibility with plug couplings. Hose material: flame-retardant polyurethane PUR. Working pressure: 20 bar. Operating temperature: from -35°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSpecial high-pressure version of the SMOOTHBORE Teflon hose with a thickened wall made of specially processed Teflon (reduced microporosity) for applications with high-pressure gases in a double braid (aramid and steel braid) and with an outer layer of Hytrel. The outer layer of Hytrel is available in four colors: black, blue, green, and red, to indicate the hose's intended use for a specific type of gas. When both HPG inner layer and AS antistatic layer are required, the HPG/AS hose (red color) can be used, featuring an additional thin AS antistatic layer inside the primary inner layer of natural HPG Teflon. Installation: use AF-TL series fittings and sleeves... Hose material: smooth PTFE (Teflon) HPG. Reinforcement: aramid braid + AISI 304 steel braid. Outer layer: microperforated Hytrel (colored polyester). Working pressure: 300 bar. Operating temperature: from -50°C to +70°C (due to the outer layer of Hytrel).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong pressure hose designed for the transmission of water or compressed air in irrigation systems, agriculture, mines, construction sites, etc. The inner layer is smooth, ensuring minimal flow loss. The outer layer is slightly longitudinally ribbed, which increases abrasion resistance and protects against contact with hot elements. Resistant to abrasion, ozone, weather conditions, oil, fuels, and a wide range of chemicals. Lighter and more flexible than standard rubber hoses. Flat when at rest, facilitating handling and storage. Does not require washing and drying. Resistant to longitudinal loads – during unwinding and pulling (longitudinal force should never exceed 1/3 of the specified breaking force, installation of fittings should consider longitudinal force). Use for air should always be preceded by a risk analysis in case of accidental disconnection or rupture of the hose. Hose material: black NBR/PVC blend embedded in a polyester-polyamide braid during the hose extrusion process. Working pressure: from 10 bar to 25 bar (water), from 7 bar to 18 bar (air) - depending on the hose diameter. Operating temperature for water: from -20°C to +80°C, temporarily up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose designed for high-pressure centralized lubrication systems. Standard: DIN 1283. Inner layer: polyethylene blend. Reinforcement: double polyester braid. Outer layer: micro-perforated polyurethane. Operating temperature: from -20°C to +40°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible, suction and pressure hose designed for the pressurized transfer of water, beer, wine, alcohols with a concentration of up to 20%, juices, beverages, other liquid food substances, and light chemicals. Not recommended for milk and its derivatives, oils, and fatty food substances. Reinforcement with a galvanized steel wire spiral embedded in the inner layer of PVC provides good resistance to vacuum and hose collapse. The smooth inner layer reduces flow losses and ensures ease of cleaning. Thanks to the braided reinforcement, the hose has high pressure resistance and low deformation under pressure. Standards and requirements: Food industry, food contact: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B, and C), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: polyester braid, steel spiral. Working pressure: from 10 bar to 20 bar, depending on the hose diameter. Vacuum: 0.9 bar. Operating temperature: -5°C to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery flexible and elastic, universal suction and discharge hose intended for water, liquids, and light chemicals. Used for loading and unloading tankers, pallet containers, and for liquid transfer in industrial installations, etc. Maintains high flexibility at low ambient temperatures. The smooth inner wall facilitates hose cleanliness and increases discharge efficiency by 20% compared to typical rubber hoses. The outer layer is resistant to abrasion and weather conditions. In the food industry, it can be used for the transfer and handling of hydrated, acidic food, and alcohols up to 20%, e.g., juices, beverages, beer, wine (simulants A, B, C; up to +40°C and 2 hours). Not recommended for milk and its derivatives, as well as oils and fatty food substances. The VACUPRESS SUPERELASTIC hose complies with European requirements 1978/142/EEC, 1935/2004/EC, 1895/2005/EC, and 10/2011/EU (simulants A, B, C), 2023/2006/EC (GMP). Suitable for temporary contact with food during the transfer of food substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International). Inner layer: white PVC. Reinforcement: steel spiral, polyester braid. Outer layer: black PVC. Working pressure for a temperature of 20°C: from 5 bar to 20 bar - depending on the hose diameter. Operating temperature: from -25°C to +60°C. As the operating temperature increases, the working pressure value of the hose decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality universal hose designed for air, cold and hot water, oil, hydraulic fluids, light chemicals, diluted acids, cleaning fluids. Strong and flexible, resistant to twisting and kinking. Non-soiling outer layer, weather-resistant, abrasion-resistant, and oil-resistant. Due to its high durability and low elongation, it is particularly recommended for drum reels. The hose is non-conductive (R > 1 MΩ per inch of hose length at 1000 V DC). Inner layer: black NBR rubber. Reinforcement: synthetic braid. Outer layer: blue (red for diameter 15.9 mm) Chemivic® rubber blend (NBR/PVC). Working pressure: 21 bar. Operating temperature: from -29°C to +88°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, transparent, strong, and flexible hose made of polyester-polyurethane, free of plasticizers, exceptionally resistant to abrasion and tearing, characterized by flexibility even at low temperatures and withstands cyclic temperature changes. The hose is produced with strict dimensional tolerances from batch to batch, ensuring safe, repeatable connections with fittings. Resistant to oils, greases, fuels, and a range of chemicals. Durable against weather conditions and intensive daily use. It is used in various industrial sectors: fuel and lubrication systems, for cooling fluids in automotive applications, for air in pneumatics and industrial automation, for the transfer of abrasive and viscous products, sludges, and powders, as well as for electrical hose protection. Full hose roll length is 30 m. Working pressure defined relative to burst pressure with a safety factor of 1:5. Material: tygothane® - polyurethane-polyester (PU). Operating temperature: from -73°C to +79°C (temporarily up to +93°C). Brittleness temperature: -73°C. Hardness: 82° Shore (A). Density: 1.20 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose designed for the transmission of various chemical substances, mainly for acid solutions, bases, ketones, aldehydes, industrial alcohols, and glycols. Basic, classic rubber chemical hose. Frequently used in industrial plants and wastewater treatment facilities for discharging contaminated water and process water. Also suitable for seawater. Inner layer made of antistatic (R ≤ 10^6 Ω/m) EPR rubber (other designation: EPM). Reinforcement made of high-strength cord. Outer layer made of antistatic (R ≤ 10^6 Ω/m) EPR (EPM) rubber resistant to chemicals, abrasion, ozone, and weather conditions. Both inner and outer layers are antistatic. Inner layer: black EPM (EPR) rubber. Reinforcement: synthetic cord. Outer layer: black EPM (EPR) rubber. Working pressure: 10 bar. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose designed for washing with cold and hot water as well as light chemicals. Recommended for use in the food industry. Compliant with European regulations for food substances 1935/2004 CE and 2007/19/CE (simulated fluids A, B, C). Compatible with TR-THERMO-12-BZ130-08-SS and TR-THERMO-12-BZ140-08-SS fittings. Inner layer: gray, smooth PVC. Reinforcement: double polyester braid. Outer layer: blue PVC. Working pressure: 80 bar. Operating temperature: from -10°C to +80°C (for 80 bar up to +50°).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMedium thickness, strong and flexible hose designed for the removal of sawdust, chips, shavings, light bulk materials, etc. Specifically designed according to the requirements of the woodworking and furniture industries, it can also be used in other industrial fields. Antistatic and flame-retardant, it ensures high work safety. Less flexible and compressible than SMARTFLEX® 0.4, 0.6, and 0.7, but smooth inside, flexible even at low temperatures. With very good abrasion resistance, also resistant to microbes and hydrolysis. Contains no halogen compounds or plasticizers. Resistant to oils and gasoline. The optimal direction of medium flow is marked with an arrow. The wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special order. Antistatic properties: permanently antistatic (according to ISO 8031 resistance R <109 Ω, according to German technical regulations TRGS 727 (6.4.2.4) specific resistance R < 2.5 x 108 Ωm, according to directive 2014/34/EU (ATEX) can be used in specific explosion hazard zones - which must be preceded by a risk analysis). After effective double grounding of the spiral, it can be treated as electrically conductive – in accordance with BGI 739-2 recommendations. Flame-retardant – according to DIN 4102 class B1. Wall thickness measured between the spiral: 1.0 mm. Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery flexible, lighter than rubber, suction and discharge hose designed for the transport of water, sewage, sludge, and dry bulk materials. Used in irrigation systems, loading and unloading of tankers, in industrial installations, etc. Maintains high flexibility at low ambient temperatures. The smooth inner and outer wall facilitates hose cleanliness and increases discharge efficiency by 20%. It is resistant to weather conditions and abrasion. The hose is also available in straight, non-curved sections of 3 to 6 m. Inner layer: black PVC. Reinforcement: polyester braid, galvanized steel spiral. Outer layer: black PVC. Working pressure: from 5 bar to 16 bar - depending on the hose diameter and temperature. Operating temperature: from -25°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible suction and discharge hose designed for water, juices, beverages, beer, wine, alcohols with a concentration of up to 20%, and other food products. Not recommended for milk and its derivatives, oils, and fatty food substances. Reinforced with a hard PVC spiral, impact-resistant, providing good resistance to vacuum and hose collapse. The transparent wall allows for easy visual monitoring of flow. The smooth inner surface reduces flow losses and ensures ease of cleaning. The outer surface is slightly corrugated. In applications not involving direct contact with food (in industry, construction, agriculture), it can be used: 1) for light chemicals, water, sludges, and wastewater, other liquids (without fats, oils, and hydrocarbons); 2) for air, vacuum transfer of dust, powders, granules, and other lightly abrasive bulk substances (non-fatty). Abrasiveness and potential static electricity issues should be considered. Standards and requirements: Food industry, contact with food: compliant with European regulations 1935/2004/EC and 10/2011/EU (simulant fluids A, B, and C), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: hard PVC spiral. Working pressure: from 2 bar to 7 bar, depending on hose diameter. Operating temperature: from -10°C to +55°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose made according to hydrogen peroxide enhancement technology. Resistant to UV radiation, oxygen, and ozone. Widely used in industry and household appliances. Sterilization by steam, ethylene oxide, or radiation. Meets FDA and BfR requirements. Material: translucent silicone. Hardness: 57° Shore (A). Density: 1.15 g/cm³. Operating temperature: from -50°C to +200°C (temporarily +220°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight, flexible delivery hose, flat-foldable, for water to hydrants and equipment used by fire services. Supplied with mounted aluminum STORZ type fittings (complete hose), compliant with the technical conditions of the MSWiA Regulation of April 27, 2010, and has a CNBOP-PIB approval certificate. The hydrant hose complies with the EN 14540 standard and is used in internal hydrants according to EN-671-2. The pump hose is used for fire pumps, rescue pumps, and forestry services. In addition to fire-fighting functions, it is widely used in industry, construction, agriculture, and mining. Also available in a yellow luminescent version (DN52, DN75, 20m, for pumps). It can be used for the transmission of water, seawater, industrial water, and solutions of certain chemical substances. Inner layer: PVC insert (PU for DN110). Reinforcement: polyester braid. Working pressure: from 12 bar to 15 bar - depending on the hose diameter. Operating temperature: from -30°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight, flexible suction and discharge hose designed for the transfer of chemical substances. Made from thermoplastic vulcanizate TPV – a material that combines the processing advantages of thermoplastic polymers (PP – polypropylene) with the properties of vulcanized rubber (EPDM). Good chemical resistance - similar to EPDM rubber allows for use with many substances, including acids (hydrochloric, sulfuric), bases, salts, alcohols, glycols, and ketones, concentrated detergents. Not recommended for fuels, oils, aromatic solvents. Resistant to weather conditions, aging, and ozone. Low weight and small bending radius of the hose ensure ease of handling, which can be an advantage when transferring from tankers and containers. Note: All hose sizes have branding indicating approximate working pressure (WP 10 bar). Confirmation of resistance and application conditions requires contact with Tubes International. Inner layer: thermoplastic rubber TPV. Reinforcement: polyester braid, steel spiral. Outer layer: thermoplastic rubber TPV. Working pressure for temperature +23°C: from 12 to 14 bar - depending on hose diameter. Operating temperature: from -30°C to +80°C (working pressure dependent on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, transparent, soft, and highly flexible hose with exceptionally long service life for use in peristaltic pumps (LFL - "long flex life"). It has high fatigue resistance and exceptional spallation resistance (spallation - chipping of hose material particles due to pump rotor pressure). One of the best TYGON® hoses for peristaltic pumps - service life of 1000 hours (at back pressure of 0 bar). Resistance to particle spallation eliminates the need for frequent filter replacement and minimizes the risk of contamination. Suitable for high-viscosity fluids, viscous fluids, and shear-sensitive fluids. Widely used in the food, cosmetic, pharmaceutical, and chemical industries, in production and laboratories. The hose is free from phthalates and BPA (Bisphenol A). It meets hygiene and food contact requirements: European 1935/2004/EC and 10/2011 EU (for conditions and substances according to certification), American FDA, NSF, USP Class VI, international ISO 10993, Japanese #370/1959. Sterilization by steam or ethylene oxide is possible. Compliant with REACH and California Proposition 65 - does not contain hazardous and prohibited substances. Full hose roll length is 7.5 m (from internal diameter 19 mm - 3 m). Working pressure defined relative to burst pressure with a safety factor of 1:5. Material: PVC (special). Maximum operating temperature: up to +74°C. Brittleness temperature: -46°C. Hardness: 56° Shore (A). Density: 1.17 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality cleaning hose for the food industry. High abrasion and kink resistance. Excellent resistance to oils and fats. Suitable for use in the food, dairy, etc. industries. Inner layer compliant with FDA 177:2600. Inner layer: black NBR rubber compound. Reinforcement: synthetic braid. Outer layer: blue Carbryn® rubber protected with Microban coating. Working pressure: 20 bar. Operating temperature: from -30°C to +93°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal, highly flexible, unreinforced hose designed for non-pressurized (or very low-pressure) transfer of air, water, and liquids in general industrial applications, light chemicals (e.g., diluted acids and bases), and as a protective cover for pipes, conduits, hoses, etc. It can be used (at temperatures up to +40°C) for food substances such as juices, beverages, beer, wine, alcohols with concentrations up to 50%, milk, and its derivatives. Not recommended for oils and fatty food substances. The CRISTALLO EXTRA hose complies with European requirements 1935/2004/EC, 10/2011/EU (simulants A, B, C, and D1), 2023/2006/EC (GMP). Suitable for temporary contact with food during the transfer of food substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International). The stated working pressure is an indicative value of the recommended working pressure with a safety factor of 5:1. Hose material: transparent PVC. Operating temperature: from -20°C to +60°C, working pressure dependent on temperature.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible, pliable, and nearly smooth inside hose made of soft polyvinyl chloride (PVC) reinforced with a right-handed spiral of hard PVC. Designed for the removal of dust, smoke, fibers, extraction of contaminated air, etc. Also used for condensate drainage in air conditioning systems and as protection for wires and hoses. Hose installation with clamps on appropriate ends, pipe fittings, etc. Wall thickness of the hose is measured between the spiral. Hose material: gray, soft PVC. Reinforcement: spiral of hard PVC. Operating temperature: from -15°C to +60°C (operating vacuum dependent on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight and flexible suction and discharge hose intended for water, juices, beverages, beer, wine, alcohols with a concentration of up to 20%, and other food products. Not recommended for milk and its derivatives, oils, and fatty food substances. Reinforced with a hard PVC spiral, resistant to impacts, providing good resistance to vacuum and hose collapse. The transparent wall allows for easy visual monitoring of flow. The smooth inner surface reduces flow losses and ensures ease of cleaning. The outer surface is slightly corrugated. In applications not involving direct contact with food (in industry, construction, agriculture), it can be used for light chemicals, water, sludges and sewage, other liquids (without fats, oils, and hydrocarbons), as well as for air, vacuum transfer of dust, powders, granules, and other lightly abrasive bulk substances (non-fatty). Abrasiveness and potential static electricity issues should be considered. Available in an antistatic version LUISIANA AS - additionally features a copper wire embedded in the hose material parallel to the PVC spiral, which, when connected to the installation and grounded, ensures the discharge of electrostatic charges. This version is available on special order, example index for the antistatic version: e.g., ME-LUISIANA-AS-050. Standards and requirements: Food industry, contact with food: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B, and C), 2023/2006/EC (GMP). Hose material: transparent yellowish PVC. Reinforcement: hard PVC spiral. Working pressure: from 2 bar to 8 bar, depending on the hose diameter. Operating temperature: from -5°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMultifunctional, lightweight, exceptionally flexible and elastic hose resistant to oil and gasoline. Designed for air, water, oils, fuels, lubricants, chemicals (e.g., light acids and bases), pesticides, fertilizers, etc. Smooth outer layer resistant to weather conditions, aging, ozone, UV radiation, non-soiling. Popular and widely used in industry, construction, agriculture, automotive workshops. Inner layer: black NBR/PU/PVC blend. Reinforcement: polyester braid. Outer layer: black NBR/PVC blend. Working pressure: 25 bar. Operating temperature: from -20°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and pressure hose of the latest generation specially designed according to the high requirements of the beer processing industry. It is intended for the transfer of high-quality raw beer, pasteurized beer, and organic beer. The inner layer is completely free of phthalates, plasticizers, and animal-derived components, eliminating the risk of medium contamination and bacterial growth. The outer layer is resistant to abrasion, aging, and weather conditions. Tested and approved for beer transfer by the Technical University of WEIHENSTEPHAN in Munich – does not alter the taste of the beer. Standards and requirements: 1) General: EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) Food industry, food contact: 1935/2004/EC, 2023/2006/EC (GMP). Inner layer compliant with FDA 21 CFR 177.2600, D.M. 21/03/73, 3-A n. 18-03-Class II. Inner layer: white bromobutyl rubber (BIIR). Reinforcement: synthetic cord, steel spiral. Outer layer: red CR rubber. Working pressure: 10 bar. Operating temperature: -40°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsExceptionally flexible hose designed for compressed air. Due to features such as: lightweight, flexibility at low temperatures, resistance to elongation, it is particularly recommended for pneumatic tools, compressors, hose reels, etc. Inner layer: black PVC. Reinforcement: polyester braid. Outer layer: blue PVC. Working pressure: 15 bar. Operating temperature: from -20°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight, extremely flexible and elastic hose designed for the removal of dust, powder, contaminated air, fumes, vapors, etc. Thanks to its unique construction with longitudinal and transverse reinforcement made of synthetic fibers and a steel spiral, it features a very small bending radius, resistance to kinking, and exceptional tensile strength. Durable and reliable, widely used in industrial and household vacuum systems, in construction work for cleaning and drying, and as a protective hose. Cadmium-free in accordance with BGR 132. Discharge of electric charges through grounding of the steel spiral. The left-handed reinforcing spiral allows for the attachment of appropriate fittings for vacuum cleaners with a left-hand thread (PVC fittings for the SUPERELASTIC hose or other suitable ones). Hose mounting with clamps on appropriate ends, pipe fittings, etc. Hose material: two layers of soft PVC reinforced with fiber. Reinforcement: steel spiral coated with PVC. Operating temperature: from 0°C to +85°C (operating pressure dependent on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible hose for air, gases, water, and other media. Used in systems where there is a risk of electric charge accumulation and in explosion hazard zones. Compliant with the ATEX directive (2014/34/EU). Surface resistance R < 106 Ω. Resistant to hydrolysis, microorganisms, abrasion, and UV radiation. Calibrated outer diameter allows compatibility with plug couplings. Recommended for applications in the electronics industry, powder coating, explosion hazard zones, mining, conveyors, and part sorters. Working pressures are stated with a safety factor of 2:1 relative to the maximum pressure that does not cause hose damage. Hose material: antistatic polyurethane PUR. Working pressure: from 9 bar to 16 bar (depending on hose diameter). Operating temperature: from -30°C to +80°C. Vacuum: up to 0.95 bar (when under vacuum, the bending radius should be increased by 20%).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality suction and discharge hose designed for the transfer of aggressive chemical substances, solvents, and concentrated chemicals, characterized by high thermal and mechanical strength and the highest purity of the inner layer. The inner layer is made of white perfluoroalkoxy polymer MFA (fluoropolymer with properties similar to Teflon), mirror-smooth (prevents medium deposition on the walls and is easy to clean), odorless and tasteless, meeting high hygiene requirements (FDA, USP, European EU). Intermediate layers made of synthetic rubber, reinforced with synthetic cord, and a steel wire spiral. The outer layer is made of EPDM rubber, antistatic (R<106 Ω), abrasion-resistant, ozone-resistant, and weather-resistant. The hose features excellent chemical resistance and purity of MFA, impermeability, temperature resistance, oxidation resistance, and mechanical stress resistance. Widely used in the chemical industry due to its total resistance to most chemical substances. Suitable for the transfer of concentrated acids and alkalis (sulfuric acid, hydrochloric acid, phosphoric acid, nitric acid, sodium hydroxide, potassium hydroxide, etc.). Resistant to rigorous cleaning conditions using the Cleaning-in-Place (CIP) method. On special order, version M according to EN 12115 with two built-in copper wires for discharging electric charges. Standards and requirements: Chemical hoses: EN 12115:2011 (type Ω). Food industry, contact with food: 1935/2004/EC, 2023/2006/EC (GMP); inner layer: 10/2011/EU, USP Class VI, FDA 21 CFR 177.1550 (e-i); ISO 10993. Does not contain plasticizers, phthalates, or animal-derived substances. Assembly: use smooth fittings with a spigot ("tail" for the hose) that do not have sharp or high ribs that could cut or damage the inner layer made of MFA when tightened. The diameter of the spigot should be precisely matched to the diameter of the hose to ensure tightness. Assembly with clamp sleeves or shell clamps. Confirmation of resistance and application conditions requires contact with Tubes International. Inner layer: white MFA polymer. Reinforcement: synthetic cord, steel spiral. Outer layer: black EPDM rubber. Working pressure: 16 bar. Operating temperature: from -50°C to +170°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSUPERFLEX RADIATOR hose connector designed for engine cooling systems in vehicles and automotive-type engines (for water, ethylene glycol-based coolants). Version with textile reinforcement and a steel spiral to prevent collapse of the bent hose. It features "soft" ends, free of steel spiral, allowing for easy and tight installation on fittings using clamps. The externally corrugated design of the hose bends easily, replacing the original molded connector in many cases and ensuring uninterrupted full flow even with strong bends. The connector design complies with SAE J20 R5 standard and is resistant to temperature and coolants used in automotive applications. No data on working pressure. Operating temperature: from -40°C to +125°C. Connector material: black EPDM rubber. Reinforcement: textile braid + steel spiral.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality, highly flexible, resistant to twisting and bending universal industrial hose. Used in industry, construction, agriculture, quarries, mining, and road construction, in the oil and shipbuilding industries. The inner layer is resistant to oil, grease, light chemicals, air, kerosene, cold and hot water. The outer layer has very good abrasion resistance and resistance to animal fats and oils. Due to its high strength and low expansion, it is particularly recommended for drum reels. Outer flame resistance complies with MSHA standard 2G-14C/39. Non-conductive (R > 1 MΩ per inch of hose length at 1000 V DC). Inner layer: black NBR rubber. Reinforcement: aramid braid, for 2" synthetic braid. Outer layer: yellow Carbryn® rubber (XNBR, carboxylated NBR). Working pressure: 35 bar. Operating temperature: from -29°C to +88°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight and flexible hose designed for the transport of air, dust, powders, fine wood shavings and chips, very light bulk materials, etc. Specifically designed according to the requirements of the woodworking and furniture industries, it can also be used in other industrial fields. Compliant with DIN 26057 Type 1. Antistatic and flame-retardant, ensuring high workplace safety. Very flexible and compressible, also elastic at low temperatures. With very good abrasion resistance, also resistant to microbes and hydrolysis. Free from halogen compounds and plasticizers. Resistant to oils and gasoline. The optimal flow direction of the medium is indicated by an arrow. The wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. Antistatic properties: permanently antistatic (according to ISO 8031 resistance R <109 Ω, according to German technical regulations TRGS 727 (6.4.2.4) specific resistance R <2.58 Ωm, according to directive 2014/34/EU (ATEX) can be used in specific explosion hazard zones - which must be preceded by a risk analysis). After effective double grounding of the spiral, it can be treated as electrically conductive – in accordance with BGI 739-2 recommendations. Flame-retardant – according to DIN 4102 class B1. Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Wall thickness measured between the spiral: 0.4 mm. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose designed for cooling water in foundries, casting plants, and all applications where rubber hoses operate close to a heat source. Glass fiber covering resistant to temperatures up to +530°C caused by thermal radiation. Used in cooling systems. Particularly recommended for water installations near metallurgical furnaces. Resistant to short-term exposure to splashes of molten hot metal. Roll length: 60 m or 120 m. Inner layer: black EPDM rubber. Reinforcement: synthetic cord. Outer layer: EPDM rubber covered with glass fiber. Working pressure: 10 bar. Operating temperature: from -40°C to +120°C, external up to +530°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose with calibrated outer diameter, intended for pneumatic, hydraulic, oil, fuel, lubrication, and chemical installations. Available in colors: natural, black, blue, red, yellow. Hose material: polyamide PA 12 (nylon). Working pressure: from 19 bar to 28 bar, depending on the diameter and wall thickness of the hose. Operating temperature: from -40°C to +80°C (for water-based media +70°C). Standard: SAE J 844 (diameters from 1/8" to 5/16").
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, colorless, transparent, flexible hose that is odorless and tasteless, non-toxic, and free of DEHP phthalates. Specifically designed for use in peristaltic pumps. Used for dispensing and portioning cold and hot food products, for soaps and detergents, for paints, and in laboratories. The soft hose material (60° Shore (A)) is highly flexible and provides excellent longevity of over 500 hours of operation in a peristaltic pump. The hose is a good alternative to commonly used PVC or silicone hoses. It remains flexible even at -40°C and withstands elevated temperatures up to +121°C. It has good chemical resistance to a range of chemicals, such as acids and bases. Not recommended for fats, high-proof alcohols, and hydrocarbons. Resistant to ozone, oxygen, and sunlight, and is difficult to ignite. Characterized by low extractability (migration of material components into the medium). Meets hygiene and food contact requirements: European 10/2011 EU (for conditions and substances according to certification), American FDA, NSF-51. Sterilization possible by steam, ethylene oxide, or radiation. Full hose roll length: 15 m. Working pressure specified relative to burst pressure with a safety factor of 1:5. Material: tygoprene® - thermoplastic elastomer styrene (TPE). Maximum operating temperature: up to +121°C. Brittle temperature: -66°C. Hardness: 60° Shore (A). Density: 0.9 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLow-pressure suction and discharge hose with a transparent inner layer made of chemically resistant PFA and a thick outer layer made of transparent silicone. Designed for various applications in the pharmaceutical, cosmetic, food, and chemical industries, where, in addition to the highest purity, aseptic conditions, and chemical resistance, observation of medium flow is required. The inner layer is made of perfluoroalkoxy polymer PFA (fluoropolymer with properties similar to Teflon), transparent, mirror-smooth, odorless and tasteless, chemically inert, meeting high hygiene requirements (FDA, USP, European EU). Reinforcement with a stainless steel spiral provides good resistance to vacuum. The thick outer layer made of platinum-cured silicone with a smooth surface features non-stick properties (the hose does not "stick") and a low coefficient of friction. It can be easily cleaned using a mild detergent. The hose design combines the advantages of PFA with the flexibility of silicone and its temperature resistance. The hose has a small minimum bend radius, is flexible and elastic at low and elevated temperatures, resistant to cyclic bending according to ASTM D 2176 and dynamic loads. Standards and hygiene requirements: inner layer: USP Class VI, 3-A Sanitary Standards 18-03 Class I, 10/2011/EU, FDA, ISO 10993-4, -10, -11, non-cytotoxic (ISO 10993 Part 5), ICH Q3D; outer layer: USP Class VI, 3-A Sanitary Standards 18-03 Class I, D.M. 21/03/73, FDA, BfR, European Pharmacopoeia 3.1.9, ISO 10993-4, -10, -11, non-cytotoxic (ISO 10993 Part 5). The hose complies with 1935/2004/EC, 2023/2006/EC (GMP), manufactured in Cleanroom ISO 14644-1 Class 8, free from phthalates, adipates, nitrosamines, animal-derived substances, substances subject to EC 1907/2006 (REACH). Confirmation of resistance and conditions of use requires contact with Tubes International. For confirmation of resistance and conditions of use, please contact Tubes International. Installation: use fittings with a smooth spigot ("tail" for the hose) that do not have sharp or high ribs that could cut or damage the inner PFA layer when tightened. The diameter of the spigot should be precisely matched to the diameter of the hose to ensure sealing. Installation with clamp sleeves or bands (clamps). Inner layer: transparent PFA polymer. Reinforcement: AISI 302 stainless steel spiral. Outer layer: transparent silicone. Working pressure: from 1 bar to 3 bar, depending on the hose diameter. Operating temperature: from -30°C to +150°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPneumatic extension - ready rubber air hose made of MPX20 hose. Finished with a brass socket and Eurostandard DN7.2 quick coupling plug (compatible with standard connections). For general use, particularly for pneumatic tools, where a rubber hose with antistatic properties is required. Inner layer: black EPDM rubber. Reinforcement: textile braid. Outer layer: black EPDM rubber. Working pressure: 20 bar. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsIndustrial hose for water and air. Widely used for washing floors and industrial equipment with hot water. Suitable for outdoor use as well. Resistant to weather conditions, ozone, and abrasion. Not resistant to oil, also not recommended for air with oil mist. Inner layer: black EPDM rubber. Reinforcement: polyester braid. Outer layer: red EPDM rubber. Working pressure: 10 bar. Operating temperature: from -40°C to +100°C (temporarily up to 120°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBlack, opaque, and flexible hose made of fluoroelastomer (Viton), resistant to fuels, solvents, oils, and chemicals, particularly at elevated temperatures. Used for concentrated acids, bases, alcohols, chlorinated and aromatic solvents, hot fuels, and oils. Suitable for peristaltic pumps. Resistant to aging, ozone, sunlight, and weather conditions. Flame-retardant. The opaque black wall of the hose protects light-sensitive substances. Used in laboratories and general industrial applications. Provides an economical alternative to VERSILONTM F-5500-A hose. Full roll length of the hose is 50 m (for internal diameters from 4 mm to 12 mm - 25 m, from 15 mm - 5 m). The specified working pressure is defined relative to the burst pressure with a safety factor of 1:5. Material: fluorine rubber (FKM). Operating temperature: from -20°C to +200°C (temporarily up to +300°C). Brittleness temperature: -20°C. Hardness: 60° Shore (A) - for 4x6 mm, 70° Shore (A) - for 4x8 mm. Density: 1.90 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsReinforced polyester silicone hose is intended for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, a version with a fluorosilicone inner layer is recommended. Standard length: 1000 mm (also available in a 2000 mm section). Pressure safety factor: 3:1. The hose meets SAE J20R1 standards. Hardness (standard version) approximately 65° Shore (A), density approximately 1.26 g/cm³. Color of the outer layer: blue. Material: silicone rubber. Reinforcement: polyester spacers. Working pressure: from 0.86 bar to 8.75 bar (depending on hose diameter). Operating temperature: from -50°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose for the transmission of almost all aggressive chemical substances. Specifically designed for the petrochemical industry for fuels with high concentrations of aromatic hydrocarbons, hot oil, and solvents. Due to the high overall chemical resistance of FPM rubber, it can be used for aggressive chemicals, in many cases also at elevated temperatures. The inner layer is made of smooth black FKM fluorine rubber. Reinforcement with synthetic cord. The outer layer is made of CR chloroprene rubber, resistant to weather conditions, ozone, abrasion, and oils. Confirmation of resistance and application conditions requires contact with Tubes International, especially for temperatures above 50ºC. Inner layer: black FKM rubber (FPM, viton). Reinforcement: synthetic cord. Outer layer: black CR rubber. Working pressure: 10 bar. Operating temperature: from -25°C to +100°C.
