Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible, and smooth hose made of soft polyvinyl chloride (PVC) with small internal grooves, reinforced with a right-hand spiral of hard PVC. Designed for the extraction of contaminated air, smoke, dust removal, chips, fibers in the textile industry, etc. Widely used in various industrial applications. Self-extinguishing and flame-retardant, in accordance with the American flammability class UL 94 V-2. Hose installation with clamps on appropriate ends, pipe fittings, etc. Wall thickness is measured between the spiral. Hose material: soft gray PVC. Reinforcement: spiral of hard PVC. Operating temperature: from -10°C to +60°C (working vacuum dependent on temperature).- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible suction and discharge hose designed for the transfer of water, juices, beverages, and other food products at temperatures up to +40°C. The absence of phthalates in the hose material makes it suitable for the transfer of milk and its derivatives, as well as alcohols with concentrations up to 50% and temperatures up to +40°C. Not recommended for oils and fatty food substances. Reinforcement with a steel wire spiral embedded in a soft PVC wall provides good resistance to vacuum and hose collapse. The smooth inner wall reduces flow losses and ensures ease of cleaning. The transparent wall resistant to UV radiation allows for easy visual monitoring of flow. In applications not involving direct contact with food (in industry, construction, agriculture), it can be used: 1) for light chemicals, water, sludges, and wastewater, other liquids (without fats, oils, and hydrocarbons); 2) for air, vacuum transfer of dust, powders, granules, and other lightly abrasive bulk materials (non-fatty). Abrasiveness and potential static electricity issues should be considered. As a hose reinforced only with a steel spiral (without a braid), it exhibits some elongation under pressure, which should be taken into account in applications, especially at temperatures above +40°C. Standards and requirements: Food industry, contact with food: compliant with European regulations 1935/2004/EC and 10/2011/EU (simulants A, B, C, and D1), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: galvanized steel spiral. Working pressure: from 2 bar to 12 bar, depending on the hose diameter. Vacuum: 0.9 bar. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsExceptionally flexible and elastic suction and discharge hose designed for the transport of food substances, requiring the use of odorless and tasteless rubber. It contains no phthalates or bisphenol A. Suitable for milk and its derivatives, as well as wine, beer, and fruit juices. Not recommended for oils and fatty food substances. Commonly used in tankers for the transfer of milk. Due to its high flexibility, it can be used with drum reels. The outer layer of the hose is resistant to abrasion and weather conditions. Standards and requirements: Food industry, contact with food: 1935/2004/EC and 2023/2006/EC (GMP), D.M. 21/03/73, FDA 21 CFR 177.2600, BfR XXI cat. 2. Inner layer: white natural rubber (NR). Reinforcement: synthetic cord, steel spiral. Outer layer: blue EPDM rubber. Working pressure: 6 bar. Operating temperature: -25°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose connector RADIATOR intended for engine cooling systems in vehicles and automotive-type engines (for water, coolant fluids based on ethylene glycol). Meets the requirements of standard SAE J20 R4 Class D-1. Available as a simple connector with a length of 1000 mm. Working pressure: from 0.6 bar to 3.7 bar, depending on the diameter of the connector. Operating temperature: from -40°C to +125°C. Safety factor (burst pressure / maximum working pressure) 3:1. Connector material: black EPDM rubber. Reinforcement: textile braid.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible medium-thickness hose designed for the transport of chips, bulk materials, granules, etc. Suitable for all types of industries, particularly commonly used for the removal of chips and other solid particles in the woodworking, furniture, ceramics, and plastics industries. The medium-thick wall and dense reinforcing spiral provide higher pressure parameters compared to ECO hoses 0.4, 0.6, and 0.7. Very smooth on the inside, low compressibility, and flexible - even at low temperatures. Good abrasion resistance, also resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. The hose is marked with an arrow indicating the correct direction of medium flow. The wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. The hose is available in the following versions: ECO – standard version, ECO SE – flame-retardant material version (UL94 V-2), ECO AS – permanently antistatic version (ISO 8031: R <109 Ω, TRGS 727 (6.4.2.4): R <2.5 x 108 Ωm, directive 2014/34/EU (ATEX): can be used in specific explosion hazard zones after risk analysis), ECO SE AS – antistatic and flame-retardant version (available on special order). The ECO hose is produced in a manufacturing process compliant with sustainable development policies, using raw materials from recycled clean waste from the production process, renewable energy, closed water circulation, and other innovations. Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Wall thickness measured between the spiral: 1.0 mm. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight multi-layer hose with an inner layer made of abrasion and oil-resistant polyurethane, intermediate and outer layers made of thermoplastic blend and PVC. Highly flexible, with a small bending radius, non-kinking. Resistant to ozone, fats, oils, and light chemicals. Designed for compressed air and fluids. Widely used in the industry for pneumatic tools, air for spray guns and water-based paint applications, sandblasting, etc. Suitable for mounting on reels. The inner layer is approved for food contact - compliant with European regulations 1935/2004/EC and 10/2011/EU (simulated fluids A, B, and C), 2023/2006/EC (GMP). Inner layer: transparent polyurethane. Intermediate layer: PVC/PU (black color). Reinforcement: polyester braid. Outer layer: TPE/PVC (turquoise color). Working pressure at 20°C: 20 bar. Operating temperature: from -15°C to +60°C. As the operating temperature increases, the working pressure value of the hose decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose with steel spiral reinforcement, intended for hot water mixed with antifreeze fluids. Used in cooling and heating systems, for pumps in engines and machines. It has vacuum resistance. Inner layer resistant to heat and cooling fluids. Outer layer resistant to heat and aging. Rubber mixture compliant with DIN 73411:79 standard. Inner layer: black EPDM rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black EPDM rubber. Working pressure: 4 bar. Operating temperature: from -40°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCrystal clear, flexible, and completely biocompatible medical hose free of phthalates (DEHP). Intended for use in dialysis equipment, blood transfusion and drainage, infusion, chemotherapy, inhalation, minimally invasive procedures, catheters, and medical laboratories. Can be used with peristaltic pumps, but lifespan is limited. High transparency of the hose and non-wettability of the inner surface ensure good flow visualization and easy complete drainage of the hose. Can be connected with mechanical clamps, thermally welded, ultrasonically welded, or glued. Compliant with ISO 10993, European Pharmacopoeia 3.1.1.2, USP Class VI, and REACH requirements. Completely non-cytotoxic, non-hemolytic, and non-pyrogenic. Sterilization by steam in autoclaves, ethylene oxide, or radiation (up to 2.5 Mrad). Full hose roll length is 15 m. Medical hoses of different hardness are available, e.g., TYGON® ND100-80 (hardness 80° Shore (A)). The specified working pressure is defined relative to the burst pressure with a safety factor of 1:5. Material: PVC (special, DEHP-free). Maximum operating temperature: +74°C. Brittleness temperature: -42°C. Hardness: 65° Shore (A). Density: 1.19 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, biologically neutral hose manufactured using hydrogen peroxide enhancement technology. Retains chemical, electrical, and mechanical properties at temperatures up to +200°C. Sterilization by steam, ethylene oxide, radiation. Complies with FDA, BfR, USP (class VI), ISO 10993 quality standards (toxicity, irritation, cytotoxicity, hemolysis). Material: translucent silicone. Hardness: 62° ±5° Shore (A). Density: 1.15 ±0.03 g/cm³. Operating temperature: from -50°C to +200°C (temporarily +230°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPressure hose for the transport of anhydrous ammonia in liquid and gaseous form. Inner layer made of thick antistatic rubber (R≤106 Ω/m). Reinforcement with high-strength cord ensures a high safety factor of 5:1. Outer layer made of antistatic rubber (R≤106 Ω/m) resistant to chemicals, abrasion, ozone, and weather conditions, microperforated. Hose compliant with the requirements of standard EN ISO 5771:2008 for rubber hoses for the transport of anhydrous ammonia. The hose is particularly intended for ammonia in the production processes of nitrogen fertilizers, cleaning agents, and for the synthesis of many chemical compounds. It can also be used in other industrial sectors utilizing anhydrous ammonia, such as industrial refrigeration (refrigerant R717 – ammonia, used in large refrigeration systems; flexible hoses are primarily used for filling installations), metallurgy, and many others. The hose can also be used for ammonia dissolved in water - ammoniacal water, widely used in industries such as wastewater treatment (pH regulator), ion-exchange resin regeneration, rubber and plastics industry, and boiler water treatment. Inner layer: black synthetic rubber. Reinforcement: synthetic cord. Outer layer: black synthetic rubber, microperforated. Working pressure: 25 bar. Operating temperature: from -40°C to +55°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and discharge hose, intended for the transfer of wine, beer, fruit juices, alcohols with a concentration of up to 96%, and other food substances that do not contain fats. The inner layer is odorless and tasteless. It does not contain phthalates and bisphenol A, as well as polycyclic aromatic hydrocarbons (PAH Free), in accordance with ZEK 01.4-08 Cat.1. Tested for heavy metals. Thanks to the external corrugation, the hose is exceptionally flexible and elastic. The outer surface of the hose made of thermoplastic material with slippery fabric properties has a very low coefficient of friction, which further facilitates hose handling and eliminates friction with other hoses and equipment components. The recommended method of installation with fittings is special EASY SHELL clamp shells, shaped to fit the hose corrugation. Standards and requirements: Food industry, food contact 1935/2004/EC and 2023/2006/EC (GMP). Inner layer compliant with FDA 21 CFR 177.2600, BfR XXI cat. 2, D.M. 21/03/73. Inner layer: white, smooth butyl rubber (IIR). Reinforcement: synthetic cord, steel spiral. Outer layer: red synthetic rubber with a thermoplastic coating. Working pressure: 10 bar. Vacuum: 0.6 bar. Operating temperature: from -40°C to +120°C.
Select options This product has multiple variants. The options may be chosen on the product page / Details90° ELBOW RADIATOR designed for engine cooling systems in vehicles and automotive-type engines (for water, ethylene glycol-based coolants). Meets the requirements of standard SAE J20 R4 Class D-1. Available with arm lengths of 200, 250, and 300 mm. Working pressure: from 0.6 bar to 4.1 bar, depending on the diameter of the elbow. Operating temperature: from -40°C to +125°C. Safety factor (burst pressure / maximum working pressure) 3:1. coupling material: black EPDM rubber. Reinforcement: textile braid.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight, flat (in a resting state), pressure hose designed for water transmission. An economical solution for average working conditions. Used in agriculture, construction, and other industrial sectors. Available in two versions: HIFLAT LD (green) and HIFLAT HD (blue). Inner layer: black PVC. Reinforcement: polyester spacer. Outer layer: green PVC (LD), blue PVC (HD). Working pressure: from 2.5 bar to 10 bar - depending on the hose diameter, temperature, and type of hose (LD, HD). Operating temperature: from -20°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose designed for the conveyance of air, dust, powders, wood shavings, fine chips, light bulk materials, etc. Suitable for all types of industries, particularly frequently used for dust extraction and the removal of fine solid particles in the woodworking, furniture, ceramics, and plastics industries. Flexible and elastic, even at low temperatures. Compressible, smoother inside compared to ECO 0.4 hose. Good abrasion resistance, also resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. The hose is marked with an arrow indicating the correct direction of medium flow. Wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. The hose is available in the following versions: ECO – standard version, ECO SE – flame-retardant material version (without fire classification), ECO AS – permanently antistatic version ISO 8031: R <109 Ω, TRGS 727 (6.4.2.4): R <2.5 x 108 Ωm, directive 2014/34/EU (ATEX): can be used in specific explosion hazard zones after risk analysis, ECO SE AS – antistatic and flame-retardant version (available on special request). The ECO hose is produced in a manufacturing process compliant with sustainable development policies, using raw materials from recycled clean production waste, renewable energy, closed water cycles, and other innovations. Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Wall thickness measured between the spiral: 0.6 mm. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSpecialized suction and discharge hose for water and sewage in sanitary installations on ships, motorboats, yachts, etc. Odorless hose that does not allow odors from sewage discharge to escape outside (5-year warranty). The outer layer is resistant to marine factors and weather conditions. It has resistance to vacuum. Compliant with EN ISO 8099 standard. A special version SANITARY STAR / 7 with a working pressure of 7 bar is available upon special order. Standard length: 60 m or 120 m. Inner layer: white synthetic rubber. Reinforcement: synthetic braid, steel spiral. Outer layer: white synthetic rubber. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPneumatic extension – ready air hose made of WTZ hose with a diameter of 10 mm and a length of 10 or 15 m. Finished with a brass socket (TP-ES72-GK-10) and a plug (TP-ES72-WK-10) of the standard Eurostandard DN 7.2 pneumatic quick coupling. The simplest solution for connecting pneumatic tools. Inner layer: transparent PVC. Reinforcement: polyester braid. Outer layer: transparent PVC. Working pressure at a temperature of 20°C: 10 bar. Operating temperature: from -5°C to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality silicone hose widely used in the industry (e.g., in cooling systems and for hot air). Exceptionally resistant to mineral oil vapors. Hardness 65° Shore (A). Inner layer: blue silicone. Reinforcement: textile inserts. Outer layer: blue silicone. Operating temperature: from -60°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and discharge hose for the transfer of almost all aggressive chemical substances. Specifically designed for the petrochemical industry for fuels with high concentrations of aromatic hydrocarbons, hot oil, and solvents. Due to the high overall chemical resistance of FKM rubber, it can be used for aggressive chemicals, in many cases also at elevated temperatures. Used for the transshipment of chemicals from road and rail tankers. Inner layer made of smooth black FKM fluorine rubber. Reinforcement with synthetic cord and steel spiral. Outer layer made of CR chloroprene rubber, antistatic, resistant to weather conditions, ozone, abrasion, and oils. Two built-in copper wires for discharging electrostatic charges. Compliant with EN 12115:11 (type M). Confirmation of resistance and application conditions requires contact with Tubes International, especially for temperatures above 50°C. Vacuum: 0.9 bar. Inner layer: black FKM rubber (FPM, viton). Reinforcement: synthetic cord, steel spiral. Outer layer: black CR rubber. Working pressure: 16 bar. Operating temperature: from -25°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, thick, flexible hose designed for suction and transport of powders, grains, light granules, and other bulk materials in the food and pharmaceutical industries. Used, among others, for powdered milk, grains, rice, coffee, tea, flour (PAS version). Quite flexible, low compressibility, smooth inside, elastic even at low temperatures. Resistant to abrasion, resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. Versions: P7 M PU FOOD – standard, steel wire spiral; P7 M PU PAS FOOD – stainless steel spiral, hose material permanently antistatic (R ≤108 Ω, according to TRGS 727). P7 M PU FOOD and P7 M PU PAS FOOD hoses comply with European requirements 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 and 178.2010. Suitable for temporary contact with food during the transport of dry, bulk, non-fatty surface food substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International). Hose material: transparent polyether-polyurethane. Wall thickness measured between the spiral: 1.4 mm. Reinforcement: steel wire spiral (P7 M PU FOOD), stainless steel wire spiral AISI 301 (P7 M PU PAS FOOD). Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone elbow 90° reinforced with polyester is intended for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, the version with a fluorosilicone inner layer is recommended. Arm length: 100 mm (also available with arm lengths of 152, 250 mm). Pressure safety factor: 3:1. The hose meets SAE J20R1 standards. Hardness (standard version) approx. 65° Shore (A), density approx. 1.26 g/cm³. Color of the outer layer: blue. Material: silicone rubber. Reinforcement: polyester inserts. Working pressure: from 1.83 bar to 8.75 bar (depending on hose diameter). Operating temperature: from -50°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCream-beige flexible hose reinforced with polyester braid, odorless and tasteless, non-toxic. Resistant to temperature over a wide range from -60°C to +135°C. Flexible and elastic, resistant to deformation and abrasion. Used for pressure transfer, dispensing, and portioning of cold and hot food products, for soaps, detergents, and disinfectants, for paints and toners, pesticides, and fertilizers. The hose is an alternative to commonly used PVC or silicone hoses. It has good chemical resistance to a range of chemicals, particularly acids and bases, oxidizing agents such as hydrogen peroxide, sodium hypochlorite, or ozone. Resistant to a variety of animal and vegetable fats. Not recommended for hydrocarbons. Resistant to aging and UV radiation. Meets hygiene requirements and food contact standards - US FDA 21 CFR 177.2600, NSF-51, and 3-A. Multiple sterilization possible with steam in autoclaves, CIP and SIP cleaning of installations, ethylene oxide, or radiation methods. Full hose roll length: 15 m. Working pressure defined relative to burst pressure with a safety factor of 1:4. Material: norprene® - thermoplastic elastomer (TPE). Maximum operating temperature: up to +135°C. Brittleness temperature: -60°C. Hardness: 61° Shore (A). Density: 0.98 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality suction and discharge hose designed for the transfer of a wide range of aggressive chemical substances. The hose's broad application, primarily in the chemical industry, is conditioned by the excellent resistance of fluoropolymer FEP to aggressive solvents and concentrated alkalis and acids such as hydrochloric, sulfuric, phosphoric, nitric acids, as well as sodium and potassium hydroxides. The hose can also be used in the food and pharmaceutical industries. It is commonly used in cleanroom environments. The inner layer is made of white tetrafluoroethylene/fluoropropylene copolymer FEP (a thermoplastic fluoropolymer with properties similar to Teflon), mirror-smooth (prevents medium deposition on the walls and is easy to maintain cleanliness), odorless and tasteless, meeting high hygiene standards (FDA, USP Class VI). Intermediate layers made of white synthetic rubber include reinforcement with synthetic cord, a steel wire spiral, and two copper wires for discharging electrostatic charges. The outer layer is made of orange EPDM rubber, resistant to abrasion, ozone, and weather conditions. The hose features excellent chemical resistance and cleanliness of FEP, as well as exceptional temperature resistance. Specifically designed for Cleaning-in-Place (CIP) cleaning methods, including steam sterilization at 150ºC. Standards and requirements: Chemical hoses: EN 12115:2011 (type M). Food industry, contact with food (inner layer): USP Class VI, FDA 21 CFR 177.1550. Confirmation of resistance and application conditions requires contact with Tubes International. Inner layer: white, smooth FEP. Reinforcement: synthetic cord, steel spiral. Outer layer: orange smooth EPDM rubber. Working pressure: 16 bar. Vacuum: 0.9 bar. Operating temperature: from -40°C to +150°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible general-purpose hose reinforced with a braid for compressed air, water, and light chemicals. It can be used (at temperatures up to +40°C) for liquid and semi-liquid food products such as juices, beverages, beer, wine, alcohols with a concentration of up to 50%, milk, and its derivatives. It is not recommended for oils and fatty food substances. The REFITTEX CR hose complies with European requirements 1935/2004/EC, 10/2011/EU (simulants A, B, C, and D1), 2023/2006/EC (GMP). It is suitable for temporary contact with food during the transfer of food substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International). Inner layer: transparent PVC. Reinforcement: polyester braid. Outer layer: transparent PVC. Working pressure: from 5 bar to 30 bar, depending on the hose diameter. Operating temperature: from -20°C to +60°C, working pressure dependent on temperature.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, transparent, flexible hose made of patented thermoplastic elastomer for biotechnological applications. Suitable for use in peristaltic pumps. Non-toxic, non-hemolytic, and apyrogenic with high purity class, easily thermally weldable, which is essential in biotechnological processes. Sterilization possible in autoclave, radiation, and ethylene oxide. Resistant to concentrated acids and bases. Meets USP Class VI requirements. Hose material: thermoplastic elastomer. Hardness: 60° Shore (A). Operating temperature: from -45°C to +135°C. Key features: thermal welding using C’eal-Flex™ TPE Ultra Sealer.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight economical hose, flat in a resting state, designed for water transmission. An economical solution for low working pressures and non-demanding working conditions. Used in agriculture, e.g., for irrigation of crops, construction, and other industrial sectors. Hose material: blue PVC. Reinforcement: polyester layer. Working pressure: 3 bar. Operating temperature: from -5°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible hose with a thick wall, designed for the discharge of chips, bulk materials, granules, etc. Suitable for all types of industry, particularly commonly used for discharging chips and other solid particles in the wood, furniture, ceramics, and plastics industries. The thick wall and dense reinforcing spiral ensure high pressure parameters. Very smooth on the inside, low compressibility, and flexible - even at low temperatures. Excellent abrasion resistance, also resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. The hose is marked with an arrow indicating the correct direction of medium flow. The wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. The hose is available in the following versions: ECO – standard version, ECO SE – version made of flame-retardant material (UL94 V-2), ECO AS – permanently antistatic version (ISO 8031: R <109 Ω, TRGS 727 (6.4.2.4): R <2.5 x 108 Ωm, directive 2014/34/EU (ATEX): can be used in specific explosion hazard zones after risk analysis), ECO SE AS – antistatic and flame-retardant version (available on special request). The ECO hose is produced in a manufacturing process compliant with sustainable development policies, using raw materials from recycled clean production waste, renewable energy, closed water circulation, and other innovations. Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Wall thickness measured between the spiral: 1.4 mm. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDesigned for water installations, seawater, cooling water including treatment agents, drinking water, acids and bases in low concentrations, salt solutions, esters, and ketones. Not suitable for mineral oils, cooling water with anti-corrosive agents containing oil, or oil-laden air. Marked on the single sleeve with a red stripe. Inner layer: butyl rubber (IIR) / EPDM. Reinforcement: nylon cord. Outer layer: EPDM rubber. Flanges: galvanized carbon steel. Operating temperature: from -40°C to +100°C (temporarily +120°C depending on the medium).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDesigned for use in installations where the medium consists of mineral oils, vegetable and animal fats, aerosol oils, water with added anti-corrosive substances. Inner layer: NBR rubber. Reinforcement: nylon cord. Outer layer: CR rubber. Flanges: galvanized carbon steel. Operating temperature: from -30°C to +90°C (depending on the medium).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDesigned for use in installations where the medium consists of hot and cold water, water with the addition of treatment agents, industrial water, seawater, glycol, weak acids, bases, esters, and ketones. Not intended for conveying media containing oil. BV (Bureau Veritas) certification. Inner layer: EPDM rubber. Reinforcement: nylon cord. Outer layer: EPDM rubber. Flanges: galvanized carbon steel. Operating temperature: from -30°C to +90°C (depending on the medium).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality multifunctional flexible hose produced in the United Kingdom. Designed for water, air, and light chemicals. The hose material is free from phthalates, silicone, and cadmium, compliant with RoHS and WEEE regulations. According to EU requirements, use for food products is possible after conducting the required migration tests using appropriate model fluids simulating the specific type of food (the material used for hose production complies with the requirements of 10/2011/EU and FDA 21). The hose material is self-extinguishing according to UL94-V2 and UL94-HB (at a thickness of 3 mm). Inner layer: transparent PVC. Reinforcement: polyester braid. Outer layer: red (R) or blue (BL) PVC. Working pressure: from 10 bar to 18.3 bar - depending on the hose diameter. Operating temperature: from -20°C to +55°C (temporarily +65°C, cold bending temperature down to -45°C). As the operating temperature increases, the working pressure value of the hose decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction and discharge hose designed for the transfer of liquid chemicals, including aggressive acids, bases, alcohols, and other detergents used for cleaning installations in food processing plants (selection according to the principles in the "Chemical Hoses" section of this catalog). The inner layer made of UPE complies with FDA requirements for food contact. Widely used in the food, cosmetic, chemical, and petrochemical industries. It features a copper wire ensuring electrical continuity between the hose ends. The outer layer is resistant to abrasion, ozone, and weather conditions. Compliant with EN 12115:11 requirements (type M, resistance between hose ends R ≤ 100 Ω, guaranteed for hoses up to 40 m in length). Standards and requirements: 1) Chemical hoses EN 12115:2011. Food industry, food contact (inner layer) 1935/2004/EC, 2023/2006/EC (GMP), 10/2011/EU (simulant fluids A, B, D2), FDA 21 CFR 177.1520, BfR III. Installation: use smooth fittings with a spigot ("tail" to the hose) without sharp or high ribs that could cut or damage the inner UPE layer when tightened. The spigot diameter should be precisely matched to the hose diameter to ensure tightness. Installation with clamp sleeves or shell clamps. Inner layer: white polyethylene UPE. Reinforcement: synthetic cord, steel spiral. Outer layer: blue EPDM rubber. Working pressure: 16 bar. Vacuum: 0.8 ÷ 0.9 bar - depending on the hose diameter. Operating temperature: -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose designed specifically for transporting cooling water, used in metallurgical furnaces, transformer cooling systems, and electrical converters. Used in steel metallurgy. The outer layer is coated with fiberglass resistant to heat radiation up to +550°C (temporarily) and splashes of hot materials. The inner layer is insulating (dielectric), R>10^11Ω, resistant to electrical breakdown E≥6000 V/mm, with increased resistance to water and steam penetration under extreme operating conditions. The minimum bending radius in the technical specifications is given for pressures above 3 bar. Inner layer: light blue, insulating EPDM rubber. Reinforcement: synthetic cord. Outer layer: EPDM rubber coated with fiberglass. Working pressure: 20 bar. Operating temperature: from -35°C to +120°C, external up to +550°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose made according to platinum-enhancing technology of exceptional purity, intended for biotechnological applications. Resistant to high temperatures, ozone, radiation, moisture, and atmospheric conditions. Does not adsorb or absorb odor or taste. Can be repeatedly sterilized in an autoclave as well as with ethylene oxide or radiation. Meets FDA, USP Class VI, ISO 10993, European Pharmacopoeia 3.1.9, and Japanese Pharmacopoeia - Chapter 51 requirements. Safety factor 5:1. Material: transparent silicone. Hardness: 50° Shore (A). Density: 1.17 g/cm³. Operating temperature: from -65°C to +260°C. Hose length: 7.62 m, 15.24 m, or 30.48 m.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, glassy transparent, flexible hose free of odor and taste, non-toxic, phthalate-free and BPA (Bisphenol A) free. Designed for the transfer and dispensing of food products, particularly dairy products, spices, vitamin concentrates, flavors, etc. The smooth, non-porous inner surface of the hose eliminates the problem of product particle settling and bacterial growth. Resistant to alkaline cleaning agents. Can be used with peristaltic pumps (moderate lifespan). Meets hygiene and food contact requirements: European 1935/2004/EC and 10/2011 EU (for conditions and substances according to certification), American FDA, NSF-51, NSF-61, 3-A, Japanese #370/1959 and MHLW370(3-D). Sterilization by steam or ethylene oxide is possible. Compliant with REACH and California Proposition 65 – does not contain hazardous and prohibited substances. Full roll length of the hose is 15 m (from an inner diameter of 50.8 mm - 6 m). Working pressure specified relative to burst pressure with a safety factor of 1:5. Material: PVC (special). Maximum operating temperature: +74°C. Brittleness temperature: -36°C. Hardness: 66° Shore (A). Density: 1.21 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight and very flexible suction and discharge hose, designed for general industrial applications (in industry, construction, agriculture). It can be used for water, light chemicals, sludges and wastewater, plant protection products, other liquids (without fats, oils, and hydrocarbons) as well as for air, vacuum transport of dust, powders, granules, and other lightly abrasive bulk materials (non-greasy). Abrasiveness and potential static electricity issues should be considered. Reinforced with a hard PVC spiral, impact-resistant, providing good vacuum resistance and preventing hose collapse. The smooth inner surface reduces flow losses and ensures ease of cleaning. The outer surface is slightly corrugated, with smooth surfaces for small diameters. As a hose reinforced only with a hard PVC spiral, lacking a braid, it exhibits some elongation under pressure, which should be taken into account in applications, especially at elevated temperatures. Hose material: green transparent PVC. Reinforcement: hard PVC spiral. Working pressure at 20°C: from 2 bar to 6.5 bar - depending on the hose diameter. As the operating temperature increases, the working pressure value of the hose decreases. Operating temperature: from -25°C to +55°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong, thick, flexible hose designed for suction and transport of abrasive bulk materials, granulates, roofing gravel, industrial cleaning, abrasive for sandblasting, silos, bulk material tankers, etc. Compliant with DIN 26057 Type 4 (SMARTFLEX® 2.0). Antistatic and flame-retardant, ensuring high workplace safety. Thick wall and dense, robust reinforcing spiral provide high resistance to vacuum. Smooth inside, non-compressible, not very flexible but elastic, even at low temperatures. Very good abrasion resistance, also resistant to microbes and hydrolysis. Free from halogen compounds and plasticizers. Resistant to oils and gasoline. The optimal flow direction of the medium is marked with an arrow. The wall thickness of the hose is measured between the spiral. Other diameters may be available upon special request. Antistatic properties: permanently antistatic (according to ISO 8031 resistance R <109 Ω, according to German technical regulations TRGS 727 (6.4.2.4) specific resistance R < 2.5 x 108 Ωm, according to directive 2014/34/EU (ATEX) can be used in specific explosion hazard zones - which must be preceded by a risk analysis). After effective grounding of the spiral on both sides, it can be treated as electrically conductive – in accordance with BGI 739-2 recommendations. Flame-retardant – according to DIN 4102 class B1. Wall thickness measured between the spiral: 2.0 mm (SMARTFLEX® 2.0), 2.5 mm (SMARTFLEX® 2.5). Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone elbow 180° reinforced with polyester is intended for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, a version with a fluorosilicone inner layer is recommended. Standard arm length: 102 mm. Pressure safety factor: 3:1. The hose meets SAE J20R1 standards. Hardness (standard version) approx. 65° Shore (A), density approx. 1.26 g/cm³. Color of the outer layer: blue. Material: silicone rubber. Reinforcement: polyester spacers. Working pressure: from 2 bar to 8.12 bar (depending on hose diameter). Operating temperature: from -50°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, crystal-clear, flexible chemical hose with a multi-layer construction featuring an inner layer made of FEP fluoropolymer with unique resistance and chemical inertness. It exhibits significantly greater flexibility than rigid hoses made entirely of Teflon or other fluoropolymers. The smooth inner layer, resistant and chemically inert, eliminates the risk of fluid contamination. Resistant to a wide range of chemicals from corrosive substances to MEK-based solvents. The hose meets hygiene requirements and is suitable for food contact: US FDA 21 CFR 177.1550, free from phthalates and BPA (Bisphenol A), non-toxic, and does not leave any odor or taste. Sterilization with ethylene oxide. Used in various industrial applications: chemical flow, pharmaceuticals, food and beverage production and packaging, paint, solvent and adhesive manufacturing, inks and toners, photographic chemicals, fertilizers and pesticides, in semiconductor production. Full hose roll length: 15 m. Working pressure defined relative to burst pressure with a safety factor of 1:5. Material: special FEP / PVC. Maximum operating temperature: +74°C. Brittleness temperature: -36°C. Hardness: 66° Shore (A). Density: 1.21 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight and flexible flat-folded suction hose with fittings for water for fire pumps. Used for fire, rescue, and forestry motor pumps. In addition to fire-fighting functions, widely used for water transfer in industry, construction, agriculture, and mining. The inner layer is smooth, resistant to mold and rot. The outer layer (braid) has high strength, with a polyurethane coating that does not retain dirt, increasing resistance to abrasion and contact with flames. Certifications: hoses compliant with the technical conditions of the MSWiA Regulation of April 27, 2010, hoses with fittings (complete hoses) have CNBOP-PIB approval certificates. Inner layer: smooth polyurethane. Reinforcement: polyester braid. Outer layer: red polyurethane coating. Working pressure: from 12 bar to 15 bar - depending on the hose diameter. Operating temperature: from -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone pressure hose REDSIL has versatile applications over a wide temperature range. It is used for both hot air and, for example, in cooling systems. Designed for liquids and gases, it is employed in various industrial sectors, including the chemical industry. Inner layer: transparent silicone. Reinforcement: olpot PET (polyester). Outer layer: red silicone. Hardness: 70° ±5° Shore (A). Operating temperature: from -50°C to +200°C.
