Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsSTOP valve series STP-B with internal thread is a pneumatically controlled valve. It allows air flow through the valve upon simultaneous application of a pneumatic control signal (pilot). In the event of a loss of the control signal, the valve is closed in both flow directions. The STP-B valve installed in the actuator supply connection causes, in the absence of pressure at the control connection (pilot), the stopping of the actuator movement. The use of STP-B valves as safety valves should be preceded by an appropriate risk analysis of the pneumatic system or the entire device. Operating pressure: 0.5 to 10 bar. Operating temperature: from -10°C to +60°C. Body material: nickel-plated brass. Sealing: NBR.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFR + L series NEW DEAL set with a high degree of reliability for heavy working conditions, featuring a piston-type reducer. It is characterized by stable set pressure under variable supply pressure, micrometric oil dosing adjustment proportional to air flow, guaranteed operation at low flow rates. Output pressure range: 0÷8, 0÷12 bar. Supply pressure: up to 18 bar, for discharge RA up to 10 bar. Operating temperature: up to +50°C. Connection: BSP 1/4", 3/8", 1/2". Pressure gauge connection: BSP 1/8". Condensate discharge: manual / semi-automatic (RMSA), automatic (SAC, RA). Flow rate: 500 l/min - 1/4", 2200 l/min - 3/8", 1/2" (at input pressure 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure adaptor type A203 with external BSP thread (60° cone seal) and internal NPT thread (thread seal). Material: AISI 316L steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBLOWSTAR nozzle with a double nipple for air guns, finished with a metric thread M12x1.25. It features a low noise level - only 74 dB at a pressure of 6 bar, without compromising the blowing force. It meets the following safety standards and directives: OSHA 1-13.1 (European Agency for Safety and Health at Work), 2003/10/EC, 2006/42/EC, EN 12100. Nominal flow: 295 l/min at a pressure of 6 bar. Material: zinc casting (nozzle), aluminum (nipple).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFilter - GAFR series GA pressure regulator with internal BSP thread is used to remove contaminants contained in compressed air to ensure the proper operation of pneumatic system components, while the manually adjustable regulator maintains a constant pressure value at the outlet, regardless of fluctuations in supply pressure. The package includes a mounting bracket/holder and a pressure gauge. GA connection sets (L, T, U shapes) are used to connect individual components together. Size: 200, 300, 400, 600. Filtration degree: 40 µm. Supply pressure: up to 10 bar. Operating temperature: from -5°C to +70°C. Connection: BSP female thread 1/8" to 1". Condensate drain: automatic (A). Flow rate: 1050 l/min - size 200, 2250 l/min - size 300, 4000 l/min - size 400, 6500 l/min - size 600 (at inlet pressure 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCAMLOCK DU connector socket with internal BSP thread (flat polyurethane gasket) manufactured according to the American military standard MIL-C-27487 (A-A-59326), commonly used as a transfer connection, particularly in the petrochemical industry. Working pressure: up to 10 bar, depending on the size of the connector. Material: aluminum. Levers: AISI 304 steel (in sizes 1.1/4" to 4" - levers made of brass). Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHydraulic screw end, type S, with metric tube, sealing with a cutting ring (BES), angled 45°, heavy series. Designed for screwing into rubber and thermoplastic hoses using a screw sleeve. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPUSH-ON JIC end fitting with internal UNF thread, type YJW110, designed for self-clamping hose intended for this type of fitting. Mounted to the hose without the use of clamps or bands. Features a special profile of grooves adapted to the material and dimensions of the PUSH-ON hose and the structure of its braid, causing the hose to clamp onto the grooves of the fitting. The fitting should not be used with other hoses or clamped with bands or clamps, as this may damage the hose. Operating temperature: from -40°C to +80°C. Working pressure in accordance with the specifications of the PUSH-ON hose. Material: galvanized carbon steel, brass, AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDIN 8537/20033 nut with Rd thread intended for a tapered end with a "tail" for a hose. Material: galvanized cast iron. Working pressure: 16 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRUBBER P-CLIP clamp compliant with DIN 3016 standard recommended for the safe and vibration-damping installation of pipes, hoses, hose bundles, corrugated electrical installation pipes (hose covers), etc., where there is a risk of abrasion and damage. This type of clamp has a wide range of applications, including: agricultural and construction machinery, internal combustion engine construction, railway industry, electrical equipment, household appliances, etc. It is made from a single piece of bent steel strip and a rubber flange. The holes at both ends of the strip are reinforced with steel plates, ensuring resistance to compression under high mechanical loads. The strip is made of AISI 304 stainless steel (W4), and the profile is made of EPDM rubber resistant to water, abrasion, temperature changes, and aging. The W4 version is recommended for marine industry applications. The clamp does not include a screw, washer, or nut. Material: AISI 304 steel (strip), EPDM rubber (flange). Strip width: 15 mm.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUpper protective plate for mounting DIN 3015 clamp standard type 100/101. Material: carbon steel, galvanized or AISI 304 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdjustable 90° elbow fitting JIC 37° with external NPT thread (seal on the thread – with Teflon tape or anaerobic sealant). Material: AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSide plug distributor, type R44, designed for connecting wires and other components in pneumatic systems. Easy and quick to use for multiple assemblies without loss of sealing on the mechanical and pneumatic sides. Material: plastic. Working pressure: 12 bar. Working medium: vacuum, air. Operating temperature: from -20°C to +60°C. Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction and pressure hose designed for the transfer of dry or liquid abrasive substances, granules, etc. Externally corrugated, internally smooth. The inner layer is made of transparent, abrasion-resistant polyurethane, with a thickness ranging from 0.6 mm (DN30) to 1 mm (DN100). The hose features a copper wire arranged in a spiral along its length, which discharges electric charges when grounded or connected to an end fitting. Widely used in plastic processing in applications requiring higher resistance to abrasion, puncturing, and cutting of the hose. Particularly recommended for plastic regenerates with relatively sharp edges. Standards and requirements: food industry, contact with food: compliant with European regulations 1935/2004/EC and 10/2011/EU (simulant fluids A, B, and C), 2023/2006/EC (GMP) – applihose to liquid food substances. Inner layer: transparent polyurethane. Outer layer: transparent PVC. Reinforcement: hard PVC spiral. Working pressure: from 3 bar to 5 bar, depending on the hose diameter and temperature. Vacuum: up to 0.7 bar. Operating temperature: -10°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible rubber fire hose, designed for use on reels. The ANKARA EN hose is manufactured according to the EN 694 standard, which is the European standard for hoses used in fixed fire protection installations and commonly used on reels in fixed hydrants in buildings, industrial installations, shopping centers, etc. The inner layer is made of EPDM rubber, resistant to light chemicals and fire-fighting foaming agents. The outer layer is made of EPDM rubber, resistant to abrasion and weather conditions. It performs excellently when mounted on reels, ensuring water flow even when the hose is not fully extended. The presented ANKARA hose is made according to the requirements of the older DIN 14817: 1991 standard, intended for powder and foam extinguishing agents, with an inner layer made of conductive NR/SBR rubber and a working pressure of up to 20 bar, also designed for use on reels. Inner layer: EPDM rubber (ANKARA EN), conductive NR/SBR rubber (ANKARA). Reinforcement: synthetic cord. Outer layer: EPDM rubber (ANKARA EN), SBR rubber (ANKARA). Working pressure: from 7 bar to 20 bar - depending on the size and type of hose. Operating temperature: from -20°C to +60°C (ANKARA EN), from -40°C to +70°C (ANKARA).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible, and elastic hose designed for the extraction of hot vapors, smoke, gases, dust, cooling air discharge, and blowing. Flame-retardant, resistant to temperature, UV radiation, ozone, and aging. Used in all areas of industry for high-temperature applications, including extraction from furnaces in the metallurgical industry, foundries, glass, and ceramic industries. Characterized by high compressibility, strong construction resistant to vibrations and stretching, and impact resistance due to the external spiral. Other diameters available upon special request in the range of 50 to 508 mm. Hose installation on couplings with bridge clamps (left-handed). Standard length: 3 m (also available in lengths of 6 and 10 m upon special request). Hose material: glass fabric impregnated with silicone (silver-gray), with a thickness of 0.4 mm. Reinforcement: external spiral made of galvanized steel wire and sheet. Operating temperature: from -60°C to +300°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose designed for hydraulic oil installations, fuels, water-based fluids. Available on request in micro-perforated version (for gases and air). Inner layer: polyester. Reinforcement: steel braid. Outer layer: polyurethane. Working pressure: from 70 bar to 325 bar, depending on hose diameter. Operating temperature: from -40°C to +100°C (for water and air up to +70°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick-connect plug for water NiTO CLICK 3/4" with internal thread. NiTO CLICK quick-connects are water quick-connects made according to the profile of very popular plastic garden quick-connects and are compatible with them. Sealing is achieved using an O-ring placed externally on the plug. Manufactured in Denmark – 5 years warranty. They maintain the simplicity of commonly known plastic quick-connects and are characterized by strength and durability. Designed for water, water with cleaning agents for use in industry, services, horticulture, agriculture, etc. Material: chrome-plated brass (matte - satin). Working pressure: up to 25 bar. Operating temperature: from -30°C to +80°C. Sealing: NBR (not suitable for gasoline and oils).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe quick exhaust valve is used to increase the speed of the actuator by rapidly venting air. Body material: nickel-plated brass. Cover material: nickel-plated brass (1/8" ÷ 1/4"), anodized aluminum (1/2"). Flat gasket: NBR. Lip seal: polyurethane. Maximum pressure: 12 bar. Minimum pressure: 0.5 bar. Operating temperature: from 0°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° fitting type LET-LOK® for metric tubing intended mainly for the chemical, petrochemical, pharmaceutical, energy, nuclear power, and process engineering industries. The allowable working pressure is determined based on the outer diameter and wall thickness of the tubing (details in the attachment). Material: AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure hydraulic adapter, in the shape of a 90° bent elbow, with external BSP thread (60° cone sealing) and internal BSP thread, with a swivel nut (60° cone sealing). Bent elbows are used for more efficient medium flow. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDIN 20037 adapter with external BSP and Rd thread, for use in pneumatic installations. Material: steel/zinc-coated cast iron. Working pressure: 25 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality reducing adapter for NiTO quick couplings for water with internal and external threads. Material: chrome-plated brass. Working pressure: up to 25 bar. Operating temperature: up to +80°C. Sealing: NBR (not suitable for gasoline and oils).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe SKILLAIR® series FIL filter, without end plates, is used for the precise removal of liquid and solid contaminants contained in compressed air. Size: 400. Filtration degree: 5 µm, 20 µm, 50 µm. Supply pressure: up to 13 bar, depending on the type of drain. Operating temperature: up to +50°C. Connection: BSP 1" ÷ 2". Condensate drain: manual / semi-automatic (RMSA), automatic (RA).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRubber nozzle tip with an outer diameter of 6 mm (compatible with nozzle under index EW-470K12), protecting delicate surfaces being cleaned from scratches. Material: TPU.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsScrewed hydraulic end, type S, with internal BSP thread and nut, sealing cone 60° (DKR), angled 90°. Designed for screwing into rubber and thermoplastic hoses using a screwed sleeve. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPUSH-ON end with internal BSP thread (60° cone sealing), type YBW110, designed for self-clamping hose intended for this type of end. Mounted to the hose without the use of clamps or bands. Features a special profile of grooves adapted to the material and dimensions of the PUSH-ON hose and the structure of its braid, causing the hose to clamp onto the grooves of the end. The end should not be used with other hoses or clamped using bands or clamps, as this may damage the hose. Operating temperature: from -40°C to +80°C. Working pressure in accordance with the specifications of the PUSH-ON hose. Material: galvanized carbon steel, brass, AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsJIC 37° plug with internal UNF thread (sealing on internal 37° cone). Material: AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRUBBER P-CLIP clamp compliant with DIN 3016 standard recommended for safe and vibration-damping installation of pipes, hoses, hose bundles, corrugated electrical installation pipes (hose sheaths), etc., for which there is a risk of abrasion and damage. This type of clamp has wide applications, including: agricultural and construction machinery, internal combustion engine construction, railway industry, electrical equipment, household appliances, etc. It is made from a single piece of bent steel strip and a rubber collar. The holes at both ends of the strip are reinforced with steel plates, ensuring resistance to compression under high mechanical loads. The strip is made of galvanized carbon steel (W1), and the profile is made of EPDM rubber resistant to water, abrasion, temperature changes, and aging. The clamp does not include a screw, washer, or nut. Material: galvanized carbon steel (strip), EPDM rubber (collar). Strip width: 12 mm.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDouble bottom plate for welding for the installation of DIN 3015 standard clamps type 100/101. Number of clamps: 2. For size group 0, there is one hole for a screw. For size group 1 to 6, there are two holes for screws. Material: carbon steel or AISI 316L steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSliding valve, type 4/2, electrically controlled with centering springs, designed for panel mounting. Used in hydraulic systems of industrial machines. Standardly supplied with O-rings and mounting screws. The coupling is equipped with a power status indicator LED. Material: cast iron (body), hardened steel (slider). Sealing: NBR. Maximum operating pressure: 315 bar (ports P, A, B), 160 bar (port T). Available for the following control voltages: 12 V DC, 24 V DC, 110 V AC, or 220 V AC. Operating temperature: from -20°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug coupling T-branch with plug connections for inch diameter hoses, series S, type PUTC. Economic solution for connecting flexible pneumatic hoses with inch calibrated outer diameter. Easy and quick to use. Material: plastic. Working pressure: 10 bar. Vacuum: 0.99 bar. Operating temperature: from 0°C to +60°C. Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRectangular corrugated hose reinforced with a steel spiral, for hot water and antifreeze fluids, intended for automotive and industrial cooling systems. It has vacuum resistance. Inner layer resistant to heat and cooling fluids. Outer layer resistant to overheating, oil, and aging. Inner layer: black CR rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black CR rubber. Working pressure: up to 4 bar. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThree-layer suction hose with a specific construction designed for the discharge of very hot (up to 1100°C) gases, vapors, smoke, and air. The outer layer of impregnated glass fabric with stainless steel threads provides mechanical strength, the middle thick high-temperature fabric serves as insulation, and the inner very fine stainless steel mesh separates the flow of hot gases. Flame retardant, resistant to hot sparks to some extent. Used with furnaces and engines for the extraction of very high-temperature gases in the metallurgical, ceramic, shipbuilding, aerospace, automotive, and military equipment industries. The hose has a strong construction and is resistant to damage due to the external spiral. Used exclusively as a suction hose operating under vacuum, due to the possibility of gas permeation outside under pressure (degassing). Hoses with a small internal diameter < 100 mm feature a so-called double-hose construction (the inner mesh layer constitutes a separate hose with a spiral). Hose installation on couplings with left-handed bridge clamps. Standard length: from 2 to 10 m - depending on the diameter. Hose material: 3 layers: externally impregnated glass fabric with stainless steel fibers (gray), middle layer - high-temperature insulating fabric, inside fine mesh - stainless steel. Reinforcement: external spiral made of wire and sheet metal from stainless steel. Operating temperature: from -50°C to +1100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose designed for solvents, paints, isocyanates, polyols, and water-based fluids. Suitable for operation in high humidity and saline air environments. Available on request in micro-perforated form (for gases and air). Inner layer: polyamide. Reinforcement: aramid braid + steel braid. Outer layer: polyurethane. Working pressure: from 200 bar to 500 bar, depending on hose diameter. Operating temperature: from -40°C to +100°C (for water and air up to +70°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCAMLOCK F connector plug with external BSPT thread made according to the American military standard MIL-C-27487 (A-A-59326), commonly used as a transfer connection, particularly in the petrochemical industry. Working pressure: up to 10 bar, depending on the size of the connector. Material: brass.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPressure hose for sandblasting, extremely resistant to abrasion. Thick inner layer made of rubber with exceptionally good abrasion resistance (40±5 mm³ according to ISO 4649 / DIN 53516). Exceeds the requirements of ISO 3861:2008 standard. The inner and outer layers are antistatic, preventing the accumulation of electric charges. Used for highly abrasive materials such as quartz sand, steel shot, corundum, glass in abrasive blasting of steel structures, castings, concrete surfaces, etc. Fitted with special nozzles for sandblasting. Standard length: 60 m / 40 m for a diameter of 16 mm (or 120 m - contact Tubes International). Inner layer: black NR/SBR rubber. Reinforcement: synthetic cord. Outer layer: black synthetic rubber. Working pressure: 12 bar. Operating temperature: from -40°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal manual control distribution valve with a front lever, commonly used for controlling actuator operation. It can be mounted inline, to a wall, directly to actuators, or on a connection block. Function 5/3 - five-way, three-position. Size: 1/8". Material: valve body - aluminum, slider - nickel-plated aluminum, sealing - NBR, end cover - plastic. Working pressure: up to 10 bar. Operating temperature: -10°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLET-LOK® type tee fitting for connecting inch tubes, primarily intended for the chemical, petrochemical, pharmaceutical, energy, nuclear power, and process engineering industries. The allowable working pressure is determined based on the outer diameter and wall thickness of the tube (details in the attachment). Material: AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure adaptor with external BSP thread (60° cone seal) and internal BSP thread (60° cone seal), with a swivel nut. Used in hydraulic systems for connecting hydraulic flexible hoses and pipes with other installation components (pumps, valves, quick couplings, etc.). Allows for reduction in type and size, compatible with the connections of the joined components. Material: carbon steel, galvanized.
