Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection block (adapter) designed for connecting hydraulic hoses with plate valves (distributors). Equipped with plate connections NG6 and threaded connections: for pump (P) - GW 1/2" BSP, for tank (T) - GW 1/2" BSP, for receiver (A and B) - GW 3/8" BSP, and pressure gauges (G) - GW 1/4" BSP. Material: steel. Maximum working pressure: 315 bar. Flow rate: 40 l/min. Operating temperature: from -20°C to +80°C (medium), from -20°C to +50°C (environment).- Select options This product has multiple variants. The options may be chosen on the product page / DetailsExtended bent nozzle with a hole diameter of 3 mm for air guns, finished with a metric thread M12x1.25. Tube diameter: 5 mm. Available lengths: 110 mm, 160 mm, and 260 mm. Material: nickel-plated brass. Maximum pressure: 10 bar. Operating temperature: from -10°C to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFilter with pressure regulator (filtroregulator) series SYNTESI®, with end connections 1/8", 1/4", 3/8", 1/2", 3/4", 1", is a device consisting of a filter and a pressure reducing valve. It is built from the same components as the filter and regulator, thus it has the same technical characteristics. It reduces and purifies the air supplied by the compressor. Size: SY1, SY2. Output pressure range: 0÷8, 0÷12 bar. Supply pressure: up to 15 bar for SY1 and up to 13 bar for SY2. Operating temperature: from -10°C to +50°C. Connection: BSP female thread 1/8" ÷ 3/8" for SY1 and BSP female thread 3/8" ÷ 1" for SY2. Additional connection for pressure gauge or fittings: BSP female thread 1/8" for SY1 and 1/4" for SY2. Condensate drain: manual / semi-automatic (RMSA), automatic (RA). Flow rate: 1300 l/min - 1/8", 2000 l/min - 1/4", 3000 l/min - 3/8" (SY1), 5800 l/min - 3/8" (SY2), 7200 l/min - 1/2", 7400 l/min - 3/4", 1" (at inlet pressure 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick coupling socket for water NiTO CLICK 3/4" with hose end. NiTO CLICK quick couplings are water couplings made according to the profile of very popular plastic garden quick couplings and are compatible with them. Sealing is achieved using an O-ring placed externally on the plug. Manufactured in Denmark – 5 years warranty. They maintain the simplicity of commonly known plastic couplings and are characterized by strength and durability. Designed for water, water with cleaning agents for use in industry, services, horticulture, agriculture, etc. Material: chrome-plated brass (matte - satin). Working pressure: up to 25 bar. Operating temperature: from -30°C to +80°C. Sealing: NBR (not suitable for gasoline and oils).
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° PUSH-ON fitting with internal BSP thread, type YBW210, designed for a special self-clamping hose intended for this type of fitting. Mounted to the hose without the use of clamps or bands. Features a special profile of grooves adapted to the material and dimensions of the PUSH-ON hose and the structure of its braid, causing the hose to clamp onto the grooves of the fitting. The fitting should not be used with other hoses or clamped with bands or clamps, as this may damage the hose. Operating temperature: from -40°C to +80°C. Working pressure in accordance with the specifications of the PUSH-ON hose. Material: galvanized carbon steel, AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRUBBER P-CLIP clamp compliant with DIN 3016 standard recommended for safe and vibration-damping installation of pipes, hoses, hose bundles, corrugated electrical installation tubes (hose covers), etc., for which there is a risk of abrasion and damage. This type of clamp has wide applications, including: agricultural and construction machinery, internal combustion engine construction, railway industry, electrical equipment, household appliances, etc. It is made from a single piece of bent steel strip and a rubber flange. The holes at both ends of the strip are reinforced with steel plates, ensuring resistance to compression under high mechanical loads. The strip is made of galvanized carbon steel (W1), and the profile is made of EPDM rubber resistant to water, abrasion, temperature changes, and aging. The clamp does not include a screw, washer, or nut. Material: galvanized carbon steel (strip), EPDM rubber (flange). Strip width: 15 mm.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight connector type LET-LOK® with external NPT thread for inch tubing, primarily intended for the chemical, petrochemical, pharmaceutical, energy, nuclear power, and process engineering industries. The allowable working pressure is determined based on the outer diameter and wall thickness of the tubing (details in the attachment). Available in a full-bore version - often used for thermocouple installation, with a bore diameter reamed to the tubing diameter (marked ...-TC at the end of the index). Material: AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdjustable plug distributor, type R43, designed for connecting wires and other components in pneumatic systems. Easy and quick to use for multiple assemblies without loss of sealing on the mechanical and pneumatic sides. Material: plastic. Working pressure: 12 bar. Working medium: vacuum, air. Operating temperature: from -20°C to +60°C. Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsScrewed sleeve for thermoplastic hoses type MT1 or MTH1. Use only with a screwed fitting from the same supplier (TI-S...). Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPressure hose for sandblasting, extremely resistant to abrasion. Thick inner layer made of rubber with exceptionally good abrasion resistance (36 mm³ according to ISO 4649:2014). Exceeds the requirements of ISO 3861:2008 standard. The inner layer is electrically conductive and the outer layer is antistatic, preventing the accumulation of electric charges. Used for highly abrasive materials such as quartz sand, steel shot, corundum, glass in abrasive jet processing of steel structures, castings, concrete surfaces, etc. Fitted with special nozzles for sandblasting. Inner layer: black NR/BR/SBR rubber. Reinforcement: synthetic cord. Outer layer: black SBR rubber. Working pressure: 12 bar. Operating temperature: from -35°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible water hose designed for winding on reels. Intended for use in high-pressure firefighting equipment and fire trucks (booster hose). The inner layer is resistant to extinguishing agents and foaming agents. Reinforcement made of a thick layer of high-strength cord. The outer layer is weather-resistant. The CHICAGO EN hose differs from the basic version of the CHICAGO hose by being manufactured in accordance with standard EN 1947: 2014 (type C, class 1, category 2), while the CHICAGO EN GL is manufactured in accordance with EN 1947 but features a luminescent outer layer, allowing for easy visibility in darkness or smoke. Special versions of the hose compliant with standards ASTM C-542 and BS 3169 are also available upon request. Standard roll length: 60 m (120 m upon confirmation for the basic version of the hose). Inner layer: black EPDM rubber. Reinforcement: synthetic cord. Outer layer: black EPDM rubber (yellow luminescent synthetic rubber – GL version). Working pressure: 40 bar. Operating temperature: from -40°C to +100°C, from -20°C to +60°C (EN 1947).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight, flexible, and highly bendable hose designed for the discharge of chemically aggressive vapors and gases in all industrial sectors. Excellent chemical resistance, high temperature resistance. The hose features high compressibility and impact resistance due to the external spiral. Resistant to UV radiation, ozone, aging, weather conditions, and is flame-retardant. Other diameters available in the range of 50 ÷ 508 mm and a version with a stainless steel spiral. Hose installation on couplings with bridge clamps (left-handed). PTFE EL CL version - electrically conductive hose with resistance R ≤106 Ω, compliant with ATEX Directive 94/9/EC and standard TRBS 2153, made of black PTFE. Chemical resistance verification - chemical resistance table for PTFE (preliminary selection), confirmation of resistance and application conditions - by Tubes International. Standard length: 3 or 6 m. Hose material: light brown glass fabric coated with Teflon (PTFE), thickness 0.12 mm - standard PTFE CL version, glass fabric coated with black conductive Teflon (PTFE), thickness 0.15 mm - antistatic PTFE EL CL version. Reinforcement: external spiral made of galvanized steel wire and sheet. Operating temperature: from -150°C to +250°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose designed for hydraulic oil installations, fuels, water-based fluids. For use near transformers and medium and high voltage electrical installations. Non-conductive - leakage during testing according to standards less than 50 µA for voltage 246 kV/m for 5 minutes. Standards: DIN 24951, SAE 100R7, ISO 3949-R7. Inner layer: polyester. Reinforcement: double polyester braid. Outer layer: orange polyurethane. Working pressure: from 157 bar to 220 bar, depending on hose diameter. Operating temperature: from -40°C to +93°C (for water up to +65°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug cap for CAMLOCK DC coupling made according to the American military standard MIL-C-27487 (A-A-59326). Working pressure: up to 10 bar, depending on the size of the coupling. Material: brass. Levers: AISI 304 steel. Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsElectric dividing valve, without control coil PIV for wired installation. It is a pneumatic component whose task is to control the direction of flow of the working medium in pneumatic drive and control systems by connecting or switching flow paths. Suitable for operation with high frequency and short response times. Possible installation in any position. Valve body material: aluminum. Connection thread: GW M5, GW BSP1/8”. Working medium: filtered compressed air, oiled or non-oiled. Maximum working pressure: from 6 bar to 30 bar, depending on the type of valve and coil. Operating temperature: -15°C to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSTORZ adaptor with internal BSP thread intended for transmission installations for liquid and bulk substances. Used in firefighting, irrigation systems, chemical industry, food industry, agriculture, etc. Characterized by a large, unobstructed flow diameter. With a symmetrical design of the connection part, allowing for easy connection. Elements with the same hook spacing can be connected. Material: brass. Working pressure: 16 bar. Seal: black NBR rubber.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdaptor - high-pressure tee type A117 with internal BSP thread, with a swivel nut (60° cone sealing). Material: AISI 316L steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStandard bent nozzle, for direct installation to the gun body. Nozzle length: 90 mm. Working pressure: 16 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRing for CAMLOCK coupling, type R. Material: AISI 304 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsComplete angled plug connector BANJO, type R54, designed for connecting hoses and other components in pneumatic systems. Easy and quick to use for multiple assemblies without loss of sealing on the mechanical and pneumatic sides. Material: nickel-plated brass. Working pressure: 16 bar. Working medium: vacuum, air. Operating temperature: from -20°C to +80°C. Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsScrewed hydraulic end, type S, with external metric thread, sealing on a 24° cone (CEL), lightweight series. Designed for screwing into rubber and thermoplastic hoses using a screwed sleeve. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / Details45° PUSH-ON end fitting with internal BSP thread, type YBW310, designed for self-clamping hose intended for this type of fitting. Mounted to the hose without the use of clamps or bands. Features a special profile of grooves tailored to the material and dimensions of the PUSH-ON hose and the structure of its braid, causing the hose to clamp onto the grooves of the fitting. The fitting should not be used with other hoses or clamped using bands or clamps, as this may damage the hose. Operating temperature: from -40°C to +80°C. Working pressure in accordance with the specifications of the PUSH-ON hose. Material: galvanized carbon steel, AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsO-ring sealing quick coupling NiTO. Material: EPDM. Operating temperature: up to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRUBBER P-CLIP clamp compliant with DIN 3016 standard recommended for the safe and vibration-damping installation of pipes, hoses, hose bundles, corrugated electrical installation tubes (hose sheaths), etc., for which there is a risk of abrasion and damage. This type of clamp has wide applications, including: agricultural and construction machinery, internal combustion engine construction, railway industry, electrical equipment, household appliances, etc. It is made from a single piece of bent steel strip and a rubber flange. The holes at both ends of the strip are reinforced with steel plates, ensuring resistance to compression under high mechanical loads. The strip is made of AISI 304 stainless steel (W4), and the profile is made of EPDM rubber resistant to water, abrasion, temperature changes, and aging. The W4 version is recommended for marine industry applications. The clamp does not include a screw, washer, or nut. Material: AISI 304 steel (strip), EPDM rubber (flange). Strip width: 20 mm.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° fitting type LET-LOK® with external NPT thread for metric tubing, primarily intended for the chemical, petrochemical, pharmaceutical, energy, nuclear power, and process engineering industries. The allowable working pressure of the fitting is determined based on the specific size and type of threaded connection (details in the attachment). Material: AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdjustable 90° elbow fitting JIC 37° with external BSPT thread (seal on the thread – with Teflon tape or anaerobic sealant). Material: carbon steel, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose in the system 3/4" made of corrosion-resistant acetal, resistant to solvents, oils, and greases, providing rigidity and elasticity of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and does not cause damage to cutting tools. Very easy to expand modular construction. Available lengths: 2x145 mm, 100 mm, 200 mm, 300 mm, 400 mm, 500 mm, 600 mm, 700 mm, 800 mm, 900 mm, and 1000 mm. Material: acetal. Working pressure: up to 1.4 bar. Maximum flow: 5182 l/hour. Operating temperature: up to +76°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction hose designed for the transfer of dry or liquid abrasive substances, granules, etc. Externally corrugated, internally smooth. The inner layer is made of transparent, abrasion-resistant polyurethane. The hose features a copper wire arranged in a spiral, which discharges electric charges when grounded or connected to a fitting. Widely used in plastic processing in applications requiring greater resistance to abrasion, puncturing, and cutting of the hose. Particularly recommended for plastic regrind with relatively sharp edges. Inner layer: transparent polyurethane. Reinforcement: hard PVC spiral. Hose material: transparent PVC. Working pressure: from 3 bar to 7 bar - depending on the hose diameter and temperature. Vacuum: from 0.69 bar to 0.74 bar - depending on the hose diameter and temperature. Operating temperature: from -5°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible and bendable, chemically and thermally resistant two-layer hose designed for the discharge of the most chemically aggressive vapors, gases, dust, and fibers (non-abrasive), and for the blowing of hot air. Very good chemical resistance to aggressive chemicals due to the internal layer of PTFE. In the standard version, the internal layer of white natural PTFE meets food industry requirements (FDA). In the antistatic version EL, the black internal layer of PTFE is electrically conductive (R ≤106 Ω). With an outer layer made of silicone-coated glass fabric and an inner layer of PTFE, the hose is resistant to temperatures up to 250ºC. The hose features high compressibility - up to 1:6, a strong construction resistant to vibrations, stretching, and tearing, and impact resistance due to the external spiral. Resistant to UV radiation, ozone, aging, weather conditions, and is flame-retardant. Used in the chemical industry, metallurgy, foundry, ceramics, and glass industries. Also available with a stainless steel spiral (from a diameter of 80 mm). Hose installation on couplings with bridge clamps (left-handed). Chemical resistance verification - chemical resistance table for PTFE (preliminary selection), confirmation of resistance and application conditions - by Tubes International. Standard length: from 2 to 10 m. Hose material inner layer: white PTFE Teflon film - standard version SILTEF, black conductive PTFE Teflon film - antistatic version SITEF EL. Hose material outer layer: silicone-coated glass fabric, silver-gray. Reinforcement: external spiral made of galvanized steel wire and sheet. Operating temperature: from -50°C to +250°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose designed for hydraulic oil installations, gases, air, fuels, water-based fluids. Inner layer: polyester. Reinforcement: polyester braid. Outer layer: micro-perforated polyurethane. Working pressure: from 110 bar to 130 bar, depending on the hose diameter. Operating temperature: from -40°C to +93°C (for water and air up to +65°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThrottle-return valve type MRF OFC series COMPACT "O" for direct mounting in actuator connections, used in pneumatic systems for regulating the flow rate of compressed air and the direction of flow. Equipped with an internal threaded connection. Adjustment change using a screwdriver, with the possibility of mounting a protective cover. Size: M5, 1/8″, 1/4″, 3/8″, 1/2″. Working pressure: up to 10 bar. Operating temperature: from -10°C to +70°C. Material: nickel-plated brass.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsREG pressure reducing valve, SYNTESI® series, without end connections, is used to regulate working pressure and ensures proper operation in the connected installation, regardless of the changing consumption of the medium. The valve uses a shaped diaphragm instead of a flat diaphragm, which provides higher nominal flow values due to greater diaphragm travel, increased sensitivity and response speed to setting changes, thanks to reduced static and kinetic friction of components, and greater accuracy in maintaining the set outlet pressure with changes in flow and supply pressure. In the event of an increase in outlet pressure above the set value, the diaphragm opens the drain valve and vents the reducer until the pressure value matches the setting. The push-lock mechanism allows the knob to be locked in any position by pressing it. The locking plate enables the installation of a padlock to prevent unauthorized changes to the outlet pressure setting. Additional connections at the front and back of size 1/8” can be used to connect a pressure gauge, pneumatic-electric relay, or plug couplings. The air drawn from these connections is reduced. Size: SY1, SY2. Outlet pressure range: 0÷2, 0÷4, 0÷8, 0÷12 bar. Supply pressure: up to 15 bar for SY1 and up to 13 bar for SY2. Operating temperature: from -10°C to +50°C. Connection: BSP female thread 1/8" ÷ 3/8" for SY1 and BSP female thread 3/8" ÷ 1" for SY2. Additional connection for pressure gauge or couplings: BSP female thread 1/8" for SY1 and 1/4" for SY2. Flow: 1200 l/min - 1/8", 2800 l/min - 1/4", 3350 l/min - 3/8" (SY1), 5300 l/min - 3/8" (SY2), 7400 l/min - 1/2", 7600 l/min - 3/4", 1" (at an inlet pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSTORZ coupling with hose end designed for transmission installations for liquid and bulk substances. Used in firefighting, irrigation systems, chemical industry, food industry, agriculture, etc. Characterized by a large, unobstructed diameter of flow. With a symmetrical design of the connecting part, allowing for easy connection. Elements with the same spacing of hooks can be connected. Available in forged version with a working pressure of up to 16 bar and in cast version, characterized by significantly lower strength with a working pressure of up to 6 bar. Material: aluminum. Working pressure: 16 bar (forged couplings), 6 bar (cast couplings). Seal: white NBR rubber (forged couplings), black NBR rubber (cast couplings).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdaptor - high-pressure tee type A111 with internal thread 3 x BSP (seal on the thread). Material: AISI 316L steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPUSH-ON end fitting with external BSP thread, type YBZ110, designed for self-clamping hose intended for this type of fitting. Mounted to the hose without the use of clamps or bands. Features a special profile of grooves tailored to the material and dimensions of the PUSH-ON hose and the structure of its braid, causing the hose to grip onto the grooves of the fitting. The fitting should not be used with other hoses or clamped with clamps or bands, as this may damage the hose. Operating temperature: from -40°C to +80°C. Working pressure in accordance with the specifications of the PUSH-ON hose. Material: galvanized carbon steel, brass, AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsJIC 37° plug with external UNF thread (sealing on the external 37° cone). Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight connector with internal thread enabling the connection of quick couplings and UHP hoses. Material: carbon steel, black galvanized. Working pressure: 700 bar (with a safety factor of 4), 1000 bar (with a safety factor of 2.8).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRUBBER P-CLIP clamp compliant with DIN 3016 standard recommended for the safe and vibration-damping installation of pipes, hoses, hose bundles, corrugated electrical installation tubes (hose sheaths), etc., for which there is a risk of abrasion and damage. This type of clamp has wide applications, including: agricultural and construction machinery, internal combustion engine construction, railway industry, electrical equipment, household appliances, etc. It is made from a single piece of bent steel strip and a rubber flange. The holes at both ends of the strip are reinforced with steel plates, ensuring resistance to compression under high mechanical loads. The strip is made of AISI 304 stainless steel (W4), and the profile is made of EPDM rubber resistant to water, abrasion, temperature changes, and aging. The W4 version is recommended for marine industry applications. The clamp does not include a screw, washer, or nut. Material: AISI 304 steel (strip), EPDM rubber (flange). Strip width: 12 mm.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHandy compressed air pen designed for quick removal of all contaminants from surfaces: liquids, fine chips, shavings, etc. Made of anodized aluminum. Equipped with a nozzle with one-handed flow adjustment capability - from a narrow to a wide air stream. The rubber tip at the end of the pen protects surfaces from scratching. Finished with a EUROSTANDARD 7.2 plug. Material: housing – aluminum protected by anodizing; sealing – NBR. Nozzle hole diameter: 0 ÷ 3 mm. Nominal flow: 300 l/min at 6 bar pressure. Maximum pressure: 12 bar. Operating pressure: 1 ÷ 6 bar. Operating temperature: from -10°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight connector type LET-LOK® with external BSP thread for inch tubing, primarily intended for the chemical, petrochemical, pharmaceutical, energy, nuclear power, and process engineering industries. The permissible working pressure is determined based on the outer diameter and wall thickness of the tubing (details in the attachment). Available in a full-bore version - often used for thermocouple installation, with a bore diameter reamed to the tubing diameter (marked ...-TC at the end of the index). Material: AISI 316 steel.
