Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong and very flexible and elastic pressure hose reinforced with two steel braids intended for conveying saturated steam at higher pressure. The inner layer is resistant to high-temperature steam. The outer layer is resistant to high temperature and weather conditions. For steam, use special screw-on fittings designed for steam – precisely matched to the diameter and thickness of the hose. To extend the lifespan, the hose should be emptied of steam after use to avoid the accumulation of condensate. Inner layer: black EPDM rubber. Reinforcement: double steel braid. Outer layer: red micro-perforated EPDM rubber. Working pressure: 18 bar. Operating temperature: from -40°C to +210°C (temporarily up to +230°C).- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSoft and flexible textile-reinforced suction hose designed for conveying saturated steam. Inner layer with good resistance to high temperature and saturated steam. Outer layer resistant to temperature, abrasion, weather conditions, and ozone. The hose is widely used in the industry for low-pressure saturated steam – for light applications. For steam, use special screw-on fittings designed for steam. To extend the lifespan, the hose should be emptied of steam after use to avoid the accumulation of condensate. Inner layer: black EPDM rubber. Reinforcement: synthetic cord. Outer layer: black micro-perforated EPDM rubber. Working pressure: 6 bar. Operating temperature: from -40°C to +170°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality pressure hose manufactured using platinum-enhanced technology. The inner layer of the hose is extruded. Compliant with FDA 21 CFR 177.2600, USP Class VI, European Pharmacopoeia 3.1.9, BfR XV A, Journal Officiel Brochure 1227, and CE Directive 1935/2004. At operating temperatures above +100°C, the maximum working pressure specified in the tables should be reduced by 1% for each 1°C increase in temperature. Inner layer: translucent silicone. Reinforcement: four layers of polyester braiding. Outer layer: translucent silicone. Operating temperature: from -60°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible pressure hose for general purposes. Used for air, water, light chemicals, and liquid and semi-liquid food products such as water, juices, beverages, beer, wine, and alcohols with a concentration of up to 50% (and up to 20% for hoses with the index SO-PVCSTAR-CR). Not recommended for food substances containing fats and oils. Suitable for milk and its derivatives (not suitable for milk and dairy products for hoses with the index SO-PVCSTAR-CR). Phthalate-free. Standards and requirements: Food industry, food contact: compliant with European regulations 1935/2004/EC and 10/2011/EU (simulant fluids A, B, C, and D1). For hoses with the index SO-PVCSTAR-CR: 1) General: EU 2015/863 (RoHS 3), EC 1907/2006 (REACH). 2) Food industry, food contact: compliant with European regulations 1935/2004/EC and 10/2011/EU (simulant fluids A, B, and C). Hose material: transparent PVC. Reinforcement: polyester braid. Working pressure: from 8 bar to 22 bar, depending on the hose diameter. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure hose with fittings and bend restrictors designed for cold and hot water pressure washing equipment. Resistant to detergents, oils, ozone, and weather conditions. Standard fittings: GW M22 x 1.5 (AISI 304 steel). Inner layer: black synthetic rubber. Reinforcement: double steel braid. Outer layer: black, micro-perforated synthetic rubber. Operating temperature: from -10°C to +155°C. Working pressure: 500 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, six-layer hose designed for washing with cold and hot water as well as light chemicals. Inner layer with increased temperature resistance. Intermediate and outer layers resistant to detergents and disinfectants. Outer layer of food-grade quality, with increased resistance to greases, fats, and oils. Hose highly resistant to kinking. Recommended for use in the food industry. Compliant with European requirements for food substances EU No.10/2011 (simulated fluids A, B, C). Recommended fitting TR-THERMO-12-BZ140-08-SS. Inner layer: smooth PVC. Reinforcement: double polyester braid. Outer layer: smooth PVC. Working pressure: 50 bar. Operating temperature: from -15°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction hose designed for the transfer and handling of crude oil, petrochemical products, and drilling cuttings mixed with crude oil (up to 50% aromatic compounds). It can also be used for cement, barite, seawater, and brine. The inner layer is made of black, smooth, antistatic NBR rubber. Reinforced with layers of durable synthetic cord. It features a copper wire ensuring electrical continuity between the hose ends. The outer layer is made of CR chloroprene rubber, flame-retardant, resistant to abrasion, ozone, seawater, and weather conditions. Designed as a specialized OFFSHORE hose for operation on drilling platforms. Widely used on North Sea platforms. Can be successfully used in land applications. Inner layer: black NBR rubber. Reinforcement: synthetic cord. Outer layer: black CR rubber. Working pressure: 20 bar. Operating temperature: from -30°C to +85°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose designed for the transfer of liquid products from the petrochemical industry containing up to 50% aromatic hydrocarbons, fuels, gasoline, diesel, heating oil, lubricating oils, etc. Inner layer made of black, smooth NBR rubber. Reinforcement with synthetic cord. It has copper wires ensuring electrical continuity between the hose ends – provided that it is correctly connected to the fittings. Outer layer made of black NBR rubber, resistant to oil and weather conditions. Relatively low weight and flexible hose construction make it easy to handle, characterized by a wide, universal application for fuel transfer or other compatible media under typical working conditions. Inner layer: black NBR rubber. Reinforcement: synthetic cord. Outer layer: black NBR rubber. Working pressure: 10 bar. Operating temperature: from -30°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality hose resistant to most demanding working conditions. Exceptionally flexible, lightweight, and convenient to use. Appropriate wall thickness and braid ensure the retention of the hose's cross-sectional shape. The antistatic inner layer guarantees safety when used in hazardous areas. Designed for medical gases in accordance with EN ISO 5359 standard. Particularly recommended and widely used in hospitals and ambulances. Inner layer: black, antistatic PVC R <106 Ω/m. Reinforcement: polyester braid. Outer layer: PVC in various colors to indicate the hose's intended use for specific types of media - blue (nitrous oxide), white (oxygen), yellow (vacuum), black and white (air). Working pressure: 15 bar. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong industrial suction hose for water and compressed air, designed for operation in harsh conditions in industry, road construction, and even in quarries. Inner layer resistant to oil mist. Abrasion and weather resistant. Widely used and proven in various industrial applications. Hose available in black and yellow. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black SBR rubber. Reinforcement: synthetic cord. Outer layer: black or yellow EPDM rubber. Working pressure: 20 bar. Operating temperature: from -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality thin-walled BARRIER hose for refrigerant flow in a single polyester braid for use in automotive and industrial air conditioning and refrigeration systems operating on R134a, R1234yf, R404a Suva MP52, and R22 mineral and synthetic oils PAG, POE, and PVE. The outer layer is resistant to abrasion and weather conditions. Standards: SAE J2064 type C class I. Inner layer: black CR rubber separated by a nylon (PA) layer. Reinforcement: polyester braid. Outer layer: black CIIR rubber, micro-perforated. Working pressure: 35 bar. Operating temperature: from -35°C to +125°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal, strong, and highly flexible rubber suction hose, designed for air, water, and light chemicals. It can be used for dispersive water-based epoxy and polyurethane paints. Not suitable for oils, fuels, aromatic hydrocarbons, cellulose paints, chloroprene, and others containing aromatic solvents (e.g., toluene, xylene) or gasoline. For chemical applications, we recommend contacting Tubes International. Inner and outer layers are antistatic (R<109 Ω/m), outer layer resistant to ozone, aging, and weather conditions. Inner layer: black EPDM rubber. Reinforcement: textile braid. Outer layer: black EPDM rubber. Working pressure: 20 bar. Operating temperature: from -40°C to +100°C (temporarily +120°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible hose used in pneumatic systems, hydraulic systems, tool lines, industrial robots, etc. Resistant to abrasion, solvents, fuels, hydrocarbons. Maintains flexibility at low temperatures. Shore hardness (A): 95°. Available in natural and blue colors. Hose material: polyurethane PUR. Working pressure: from 8 bar to 12 bar (depending on hose diameter). Operating temperature: from -40°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery flexible, abrasion-resistant, tear-resistant, and kink-resistant spiral hose designed for pneumatic control systems, hand tools, industrial robots, etc. Finished on both ends with straight sections of 100 mm and 500 mm and ends with external BSPT threads. The stated total length is the maximum length of the hose when stretched. Hose material: blue polyurethane PUR. Working pressure: up to 14 bar (depending on hose diameter). Operating temperature: from -40°C to +75°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, semi-transparent smooth-walled PTFE hose with excellent chemical resistance. Designed for low-pressure installations, chemicals, paints, adhesives, liquid and gaseous fuels, oils, lubricants, air, gases, water, steam, and water-based fluids. Used in all types of industry. The hose is not antistatic (does not dissipate electric charges for non-conductive substances). Not recommended for pneumatic plug connections. Can also be used as mechanical guidance for hoses or rods due to the low friction coefficient and self-lubricating properties of Teflon. Flame retardant (UL94 V-0) and with a high oxygen index (LOI). Safety factor n = 4:1. The burst and working pressure of the hose decreases at operating temperatures above 20°C and is dependent on its height. Hose material: smooth PTFE (Teflon). Shore hardness (D): 58. Operating temperature: from -200°C to +260°C. Working pressure: from 2.3 bar to 10.8 bar - depending on the hose diameter.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure delivery hose, reinforced with steel, designed for conveying superheated steam. The outer layer is resistant to high temperatures and weather conditions. Not intended for steam cleaners ("dry steam cleaners"). For water vapor, use special screw-on fittings designed for water vapor. To extend the lifespan, the hose should be emptied of steam after use to avoid condensate buildup. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black EPDM rubber. Reinforcement: double cord of steel wire. Outer layer: black or red micro-perforated EPDM rubber. Working pressure: 18 bar. Operating temperature: from -40°C to +210°C (temporarily up to +232°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose intended for high-pressure cleaning devices with cold and hot water. Resistant to abrasion, ozone, and detergents. Not suitable for steam cleaning. Standards: EN 1829-2:2008, EN 853 1SN or EN 853 2SN - dimensional compliance. Inner layer: black synthetic rubber. Reinforcement: single steel braid or double steel braid. Outer layer: black or blue synthetic rubber. Working pressure: from 210 bar to 400 bar, depending on the diameter and type of hose. Operating temperature: from -40°C to +160°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsProduced from high-quality ether-based raw material, maintaining flexibility over a long period, a spiral hose suitable for operation in harsh industrial conditions. It has shape memory, ensuring that after many years of use, the coil diameter remains unchanged. Excellent for applications requiring hoses resistant to abrasion, brittleness, and adverse weather conditions. Equipped with swivel couplings to eliminate longitudinal stresses in the hoses during use. Finished on both ends with straight sections of 100 mm and 500 mm, and ends reinforced with a quick coupling and a 26KA plug, with a reinforcing spring. The working length is 80-90% of the total length of the hose. Hose material: light blue polyurethane PUR. Working pressure: up to 12 bar (depending on hose diameter). Operating temperature: from -20°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality BARRIER type refrigerant hose (thick-walled) designed for automotive and industrial cooling and air conditioning systems operating on R134a, R12, R404a Suva MP52, and R22 refrigerants with mineral and synthetic oils PAG, POE, and PVE. The outer layer is resistant to oil, abrasion, and weather conditions. Standards: SAE J2064 type C class II. Inner layer: black CR rubber, nylon (PA) layer. Reinforcement: two polyester braids. Outer layer: black EPDM rubber, micro-perforated. Working pressure: from 17 bar to 24 bar, depending on hose diameter. Operating temperature: from -30°C to +125°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose designed for washing with cold and hot water as well as light chemicals. The outer layer is resistant to animal and vegetable fats. Recommended for use in the food industry. Compliant with European regulations for food substances 1935/2004 EC and 2007/19/EC (simulated fluids A, B, C). Use crimped fittings for THERMOCLEAN hoses. Inner layer: white, smooth PVC. Reinforcement: polyester cord. Outer layer: blue, smooth PVC. Working pressure: from 26 bar to 30 bar (depending on hose diameter). Operating temperature: from -15°C to +100°C (temporarily up to +120°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible and lightweight polyamide hose, intended for pneumatic, oil, fuel, and hydraulic installations, resistant to chemicals and lubricants. It has a calibrated outer diameter, allowing for the use of plug couplings, which significantly shortens and facilitates its installation. Compliant with DIN 73378 standard. Available in colors: yellow, orange, red, blue, green, natural, and black. Hose material: polyamide PA 12 (nylon). Working pressure: from 16 bar to 49 bar, depending on the diameter and wall thickness of the hose. Operating temperature: from -55°C to +100°C (for water-based media +70°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible welding hose for oxygen made according to ISO 3821 standards. It is characterized by resistance to kinks and weather conditions. Not recommended for gases produced from fuels, oils, and LPG gas. Inner layer: black SBR/NR rubber. Reinforcement: synthetic braid. Outer layer: blue smooth SBR/NR rubber. Working pressure: 20 bar. Operating temperature: from -20°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe HYPERLINE SB (HYDRAFLON) hose features an inner layer made of high-quality seamless PTFE, ensuring minimal porosity, maximum flexibility, and resistance to vibrations. The braid is made from heat-treated AISI 304 stainless steel wire with a tensile strength of 1700 MPa. It is used for the transmission of chemicals, food substances, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam, etc. - as well as for classic high-pressure hydraulic oil installations. The HYPERLINE SB hose is a version of the SMOOTHBORE hose with a medium wall thickness and an internal diameter adapted to standard hydraulic fittings; installation is done using standard straight clamp jaws. In cases where static electricity hazards are identified (risk of charge generation and accumulation), HYPERLINE SB hoses in the antistatic AS version should be used. The antistatic Teflon in the AS version is black (contains appropriately dispersed graphite in PTFE) and has a resistance R <10^8 Ω (according to ISO 8031 annex A). This ensures the dissipation and dispersion of electric charges. At operating temperatures above +130°C, the maximum working pressure should be reduced by 0.75% for each 1°C increase in temperature. The value "Wall thickness [mm]" provided in the Technical Data refers to the PTFE layer. Hose material: smooth PTFE (Teflon). Reinforcement: single braid of AISI 304 steel. Working pressure: from 80 bar to 350 bar - depending on the hose diameter. Operating temperature: from -70°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose for cleaning and washing installations and machines in the food industry with steam and hot water. The inner layer meets FDA 21 CFR 177.2600 and BfR XXI category 2 requirements. The outer layer is resistant to vegetable and animal fats. High-quality hose, commonly used for cleaning and washing with hot water or steam in the food industry (e.g., dairies, meat industry). Note: the hose should not be used simultaneously for water and steam. For steam, use special screw-on fittings designed for steam. To extend the lifespan, the hose should be emptied of steam after use to avoid condensation buildup. Standard roll length: 60 m (or 120 m - contact Tubes International). Inner layer: white butyl rubber. Reinforcement: synthetic cord. Outer layer: blue NBR/PVC rubber. Working pressure: 6 bar (10 bar - for water). Safety factor: 10:1 (3:1 - for water). Operating temperature: from -30°C to +165°C (from -30°C to +95°C - for water).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose intended for hot water pressure washing equipment. Inner layer resistant to detergents, outer layer resistant to abrasion, oils, ozone, and weather conditions. Standards: ISO 1307. Inner layer: black synthetic rubber. Reinforcement: single steel braid or double steel braid. Outer layer: black or blue synthetic rubber (micro-perforated). Working pressure: 250 bar or 400 bar, depending on the type of hose. Operating temperature: from -40°C to +120°C or from -40°C to +150°C, depending on the type of hose.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose with enhanced abrasion resistance for use with cold and hot water pressure washing equipment. Resistant to detergents in aqueous solutions used, for example, in pressure washers, oils, ozone, and weather conditions. Inner layer: black synthetic rubber. Reinforcement: single or double steel braid. Outer layer: micro-perforated polyurethane. Working pressure: from 210 bar to 400 bar, depending on the diameter and type of hose. Operating temperature: from -40°C to +120°C (temporarily up to +155°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose for propane-butane and natural gas. Meets the requirements of ISO 3821 standard. Inner layer: black NBR rubber. Reinforcement: two textile braids. Outer layer: orange EPDM/SBR rubber. Working pressure: 20 bar. Operating temperature: from -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality large-diameter refrigerant hose designed for automotive (especially trucks and buses) and industrial refrigeration and air conditioning systems operating on R 134a and R404a refrigerants, as well as mineral and synthetic oils PAG and POE. The outer layer is resistant to oil, abrasion, high temperatures, and weather conditions. Standards: SAE J2064 type B (dimensions SAE 100R5). Installation: use special screwed or clamped fittings. Inner layer: black IIR rubber. Reinforcement: steel braid. Outer layer: black CSM rubber, micro-perforated. Working pressure: 35 bar. Operating temperature: from -40°C to +125°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible pressure hose used for washing with cold and hot water and for the transfer of light chemicals, detergents, and disinfectants. Suitable for use in the food industry. Compliant with European requirements for food substances according to regulation 1935/2004 EC and directive 2007/19/EC (simulated fluids A, B, C). Hydraulic type fittings (TI-Z...) should be used, properly secured with sleeves, or fittings attached using two clamps, which should be tightened after the first use at higher temperatures. Fittings and sleeves should be secured after preheating the hose in water at +60°C for 30 seconds. Inner layer: white, smooth PVC. Reinforcement: synthetic cord. Outer layer: blue, smooth PVC. Working pressure: 33 bar. Operating temperature: from -15°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPressure hose, very flexible, resistant to aging, ozone, weather conditions, and abrasion. Designed for air, water, and light chemicals: non-oxidizing, diluted acids (e.g., hydrochloric and sulfuric), diluted bases, salt solutions, alcohols, acetone, ketones, glycol-based coolants. Not suitable for oils, fuels, aromatic hydrocarbons. Can be used for various water-soluble paints and those based on ketones and esters. Not suitable for cellulose paints, chlorinated rubber, and others containing aromatic solvents (e.g., toluene, xylene) or gasoline. Inner and outer layer antistatic R<106 Ω according to EN ISO 8031:2009. Inner layer: black EPDM rubber. Reinforcement: single or double (DN 32÷38) spiral textile braid. Outer layer: black EPDM rubber. Operating temperature: from -40°C to +120°C (temporarily up to +140°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSpiral hose intended for pneumatic control systems, hand tools, industrial robots, etc. Finished on both ends with a straight section of 100 mm in length and external BSPT threaded ends. The stated total length is the maximum length of the hose when stretched. Hose material: blue polyamide PA 11/12 (nylon). Working pressure: up to 27 bar (depending on the diameter and wall thickness of the hose). Operating temperature: from -40°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPUSH-IN hose for lubricating products with calibrated outer diameter intended for connection with PUSH-IN plug couplings. For operating temperatures above +20°C, the maximum working pressure of the hose should be reduced according to the correction factor value: (operating temperature/correction factor) +20°C/1.00; +30°C/0.83; +40°C/0.72; +50°C/0.64; +60°C/0.58; +70°C/0.52; +80°C/0.47. Material: polyamide 66. Operating temperature: from 0°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, semi-transparent smooth-walled PTFE hose with excellent chemical resistance. Designed for low-pressure installations of chemicals, paints, fuels, oils, greases, air, gases, water, steam, and water-based fluids – in all types of industry. As it is chemically inert and does not contain components that could leach into the internal medium, it can be used for food substances. Compliant with FDA 21 CFR 177.1550, EU 10/2011, EC 1935/2004, and Italian D.M. 174 06/04/2004. The hose is not antistatic (does not dissipate electric charges for non-conductive substances). Not recommended for pneumatic plug connections. It can also be used as mechanical guidance for hoses or rods due to the low friction coefficient and self-lubricating properties of Teflon. Flame retardant (UL94 V-0) and with a high oxygen index (LOI). Safety factor n = 3:1. The burst and working pressure of the hose decreases at operating temperatures above 20°C and is dependent on its height. Hose material: PTFE (Teflon). Operating temperature: from -60°C to +260°C. Working pressure: from 3 bar to 56 bar - depending on the diameter and wall thickness of the hose.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible pressure hose made of PVC for general purposes and food products. Used for compressed air, water, water-based coolants, light chemicals, and liquid and semi-liquid food products. The smooth inner wall reduces flow losses and ensures ease of cleaning. In the food industry, it can be used for the transfer of hydrated, acidic foods, and alcohols up to 20%, e.g., juices, beverages, beer, wine (simulants A, B, C; up to +40°C and 0.5 h). Not recommended for milk and its derivatives, as well as food substances containing fats and oils. The RAGNO CR hose complies with European requirements 1978/142/EEC, 1935/2004/EC, 1895/2005/EC, and 10/2011/EU (simulants A, B, C), 2023/2006/EC (GMP). Suitable for temporary contact with food during the transfer of food substances - under the conditions specified in the manufacturer's declaration of conformity (available from Tubes International). Inner layer: transparent PVC. Reinforcement: polyester braid. Outer layer: transparent PVC. Working pressure for a temperature of 20°C: from 8 bar to 20 bar - depending on the hose diameter. The working pressure value decreases with increasing temperature. Operating temperature: from -5°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsIndustrial hose for cold and hot water for heavy-duty conditions, requiring high flexibility, abrasion resistance, weather resistance, and ozone resistance. Used, among other applications, for cooling and thermostating injection molds. Can be used for air. Application at temperatures above +95°C reduces hose lifespan. Not oil-resistant, also not recommended for air with oil mist. Recommended installation with clamps or ferrules. Inner layer: black EPDM rubber. Reinforcement: synthetic braid. Outer layer: black, blue, or red EPDM rubber. Working pressure: 20 bar. Operating temperature: from -30°C to +95°C (20 bar), from -30°C to +140°C (10 bar), temporarily up to +160°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality hose primarily intended for cleaning rooms and equipment in the food industry. It can be used for air, cold and hot water, oil, hydraulic fluids, light chemicals, and cleaning fluids. Strong, flexible, resistant to twisting and kinking. Non-soiling outer layer, weather-resistant and abrasion-resistant, oil and fat resistant, with increased resistance to animal fats. Due to its high durability and low elongation, it is particularly recommended for drum reels. Inner layer: black NBR rubber. Reinforcement: synthetic braid. Outer layer: blue Chemivic® rubber compound (NBR/PVC). Working pressure: 20.7 bar. Operating temperature: from -29°C to +88°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHighly flexible and elastic polyurethane hose, featuring optimal mechanical properties and very high compressive strength over a wide temperature range. Calibrated outer diameter and wall thickness allow for the use of easy-to-use plug couplings from leading manufacturers. Resistant to abrasion, solvents, fuels, and hydrocarbons. Widely used in both pneumatic and hydraulic systems, in industrial robotics, and tool lines. Shore hardness (A): 90°. Available in natural, black, blue, green, red, and yellow colors. Hose material: PUR polyurethane. Working pressure: from 9 bar to 14.3 bar, depending on hose diameter. Operating temperature: from -40°C to +85°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery flexible, abrasion-resistant, tear-resistant, and kink-resistant spiral reinforced hose specifically designed for automotive workshops, for pneumatic control systems, hand tools, industrial robots, etc. Finished on both ends with straight sections of 100 mm and 500 mm in length and external BSPT threaded ends. Shore hardness (A) 98°. The stated total length is the maximum length of the hose when stretched. Hose material: blue polyurethane PUR. Working pressure: up to 15 bar. Operating temperature: from -40°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight transparent smooth-walled hose made of natural (non-regenerated) fluoropolymer FEP (fluorinated ethylene propylene), a material with properties similar to PTFE. The hose features excellent chemical resistance, dimensional and shape thermal stability, and a smooth internal and external surface. Good transparency of the hose allows for easy observation of fluid level or flow. UV resistant. Designed for low-pressure installations of aggressive chemicals or where high purity and chemical inertness of the hose material are required. Commonly used in laboratories, chemical and pharmaceutical industries. Due to its excellent insulating properties, it is used in the electronics and semiconductor industries. The hose is not antistatic (does not dissipate electric charges for non-conductive substances). Not recommended for pneumatic plug connections. Flame retardant (UL94 V-0) and with a high oxygen index (LOI). Safety factor n = 4:1. Hose material: FEP. Shore hardness (D) 55. Operating temperature: from -200°C to +206°C. Working pressure: from 4.25 bar to 13 bar - depending on the hose diameter.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, resistant to kinks and atmospheric conditions welding hose for acetylene made according to ISO 3821 standard. Not recommended for gases produced from fuels, oils, and propane-butane (LPG). Inner layer: black SBR/NR rubber. Reinforcement: synthetic braid. Outer layer: smooth red SBR/NR rubber. Working pressure: 20 bar. Operating temperature: from -20°C to +70°C.
