Our products
Select options This product has multiple variants. The options may be chosen on the product page / DetailsElectric shut-off valve V3V, SKILLAIR® series, without end plates, is used to separate the working system from the supply air. It is a normally closed, three-way valve. In the closed position, it cuts off the supply air while simultaneously venting the system, making it particularly useful during maintenance work. Size: 100. Supply pressure: up to 10 bar. Operating temperature: up to +50°C. Flow rate: 1650 l/min (at an inlet pressure of 6 bar Δp = 1 bar).- Select options This product has multiple variants. The options may be chosen on the product page / DetailsManual shut-off valve V3V series SYNTESI®, with end connections, is used to separate the working system from the supply air. It is a three-way, two-position, normally closed valve. In the closed position, it cuts off the supply air and vents the system, making it particularly useful for maintenance work. It has a system allowing for the installation of two padlocks of size SY1 or three padlocks of size SY2 with a diameter of 3 mm. Alternatively, a version with a Ø 7 hole for a single padlock is available. On the rear and front surfaces of the valve, there are auxiliary connections (1/8” for size SY1 and 1/4” for size SY2) for connecting a pressure gauge, pressure sensor, or for additional air intake. Size: SY1, SY2. Connection: BSP thread 1/8", 1/4", at the front and rear. Supply pressure: up to 15 bar, depending on the size. Operating temperature: from -10°C to +50°C. Nominal flow: up to 4000 l/min, depending on the size (at an inlet pressure of 6 bar and Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe GZ V3V series G shut-off valve with BSP internal thread is used to separate the supply air from the working part of the installation. When closed, the air behind the valve is released into the atmosphere. Particularly recommended as a safety measure during maintenance work. The package includes a mounting bracket/holder, a padlock, and 2 keys. Connection sets GA (L, T, U shapes) are used to connect individual components together. Size: 200, 300, 400. Connection: BSP 1/8" ÷ 1/2". Supply pressure: up to 10 bar. Operating temperature: up to +70°C. Control: manual.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMR FC series BIT regulator. Version with controlled bleed, allows for increased accuracy in maintaining the set output pressure value through continuous, slight venting of air to the atmosphere. Pressure gauge connection: GW 1/8" BSP. Output pressure range: 0 ÷ 2 bar, 0 ÷ 4 bar, or 0 ÷ 12 bar. Supply pressure: up to 13 bar. Operating temperature: up to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLubricator series SKILLAIR®, with end plates, ensures proper lubrication of devices in pneumatic installations with oil mist. Size: 100, 200, 300. Tank capacity: 50 cm³ - size 100, 95 cm³ - size 200, 160 cm³ - size 300. Supply pressure: up to 15 bar (13 bar - size 200, 300). Operating temperature: up to +50°C. Connection: BSP 1/4" to 1". Flow rate: 1500 l/min - size 100, 3700 l/min - size 200, 5500 l/min - size 300 (at inlet pressure 6 bar and Δp = 1 bar). Oil filling method: STD - standard version, filling through tank disassembly or plug, CA - automatic filling, replenishment only during lubricator operation, CD - vacuum filling, pressure drop inside the tank allows for filling, CAML - automatic filling with minimum level, CDML - vacuum filling with minimum level.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe pilot-operated pressure reducing valve REG P, SKILLAIR® series, is used to maintain air pressure wherever high accuracy of setting is required under varying working conditions. The valve has practically eliminated friction, which results in the aforementioned high accuracy and low hysteresis. The presence of a slight air bleed is necessary for the proper operation of the valve and is not a sign of damage. Typical for large-sized pressure reducing valves (series 400). It is recommended to use filtered air. Size: 1/4". Output pressure range: 0÷2, 0÷4, 0÷8, 0÷12 bar. Supply pressure: up to 13 bar. Operating temperature: up to +50°C. Connection: BSP female thread 1/4". Pressure gauge connection: BSP female thread 1/8". Flow rate: 140 l/min (at an inlet pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe FIL filter series SKILLAIR®, without end plates, is used for the precise removal of liquid and solid contaminants contained in compressed air. The size of the retained contaminants depends on the filtration degree of the filter element. Size: 100, 200, 300. Filtration degree: 5 µm, 20 µm, 50 µm. Supply pressure: up to 15 bar, depending on size and type of drain. Operating temperature: up to +50°C. Connection: BSP 1/4" to 1". Condensate drain: manual/semi-automatic (RMSA), automatic (SAC, RA). Flow rate: 2000 l/min - size 100, 3100 l/min - size 200, 5300 l/min - size 300 (at an inlet pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe FIL filter series SKILLAIR®, with end plates, is used for the precise removal of liquid and solid contaminants contained in compressed air. The size of the retained contaminants depends on the filtration degree of the filter element. Size: 100, 200, 300. Filtration degree: 5 µm, 20 µm, 50 µm. Supply pressure: up to 15 bar, depending on size and type of discharge. Operating temperature: up to +50°C. Connection: GW BSP 1/4" to 1". Condensate discharge: manual / semi-automatic (RMSA), automatic (SAC, RA). Flow rate: 2000 l/min - size 100, 3100 l/min - size 200, 5300 l/min - size 300 (at an inlet pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsGR series G reducer with internal BSP thread, manually adjustable, maintains a constant output pressure regardless of fluctuations in pressure before the valve. The package includes a mounting bracket and a pressure gauge. Connection sets GA (L, T, U shapes) are used for connecting individual components. Size: 200, 300, 400, 600. Supply pressure: up to 10 bar. Operating temperature: up to +70°C. Connection: BSP 1/8" to 1". Flow rate: 3000 l/min - size 200, 4000 l/min - size 300, 7500 l/min - size 400, 12000 l/min - size 600 (at input pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsGF series G filter with BSP internal thread is used for removing contaminants contained in compressed air to ensure the proper operation of pneumatic system components. The package includes a mounting bracket. GA connection sets (L, T, U shapes) are used for connecting individual components. Size: 200, 300, 400, 600. Filtration degree: 40 µm. Supply pressure: up to 10 bar. Operating temperature: up to +70°C. Connection: BSP 1/8" to 1". Condensate drain: automatic (A). Flow rate: 3100 l/min - size 200, 5000 l/min - size 300, 7500 l/min - size 400, 12000 l/min - size 600 (at inlet pressure 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsGL series G lubricator with internal BSP thread ensures proper lubrication of devices with oil mist in pneumatic installations. The package includes a mounting bracket/holder. Connection sets GA (L, T, U shapes) are used for connecting individual components. Size: 200, 300, 400, 600. Supply pressure: up to 10 bar. Operating temperature: up to +70°C. Connection: BSP 1/8" ÷ 1". Flow rate: 3200 l/min - size 200, 5400 l/min - size 300, 8300 l/min - size 400, 12000 l/min - size 600 (at inlet pressure 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFilter - GFR series G pressure regulator with internal BSP thread is used to remove contaminants contained in compressed air for the proper operation of pneumatic system components, and the manually adjustable regulator maintains a constant pressure value at the outlet, regardless of pressure fluctuations before the valve. The set includes a mounting bracket/holder and a pressure gauge. Connection sets GA (L, T, U shapes) are used to connect individual components together. Size: 200, 300, 400, 600. Filtration degree: 40 µm. Supply pressure: up to 10 bar. Operating temperature: up to +70°C. Connection: BSP 1/8" to 1". Condensate drain: automatic (A). Flow rate: 2100 l/min - size 200, 3800 l/min - size 300, 6750 l/min - size 400, 11100 l/min - size 600 (at an inlet pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSKILLAIR® D series filter, with end plates, is used for the precise removal of liquid and solid contaminants contained in compressed air. Size: 100, 200, 300. Filtration degree: 99.97% at 0.01 µm. Supply pressure: up to 15 bar, depending on size and type of discharge. Operating temperature: up to +50°C. Connection: BSP 1/4" to 1". Condensate discharge: manual / semi-automatic (RMSA), automatic (SAC, RA). Flow rate: 230 l/min - size 100, 360 l/min - size 200, 500 l/min - size 300 (at inlet pressure 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsD series NEW DEAL fine filter with coalescing element removing oil vapors. Filtration efficiency: 99.97% at 0.01 µm. Supply pressure: up to 18 bar. Operating temperature: up to +50°C. Condensate drain: manual / semi-automatic (RMSA), automatic (SAC, RA). Flow rate: 230 l/min (at inlet pressure 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDEP BIT series fine filter with coalescing element for compressed air systems or in close proximity to actuating devices. Size: 1/8", 1/4". Maximum inlet pressure: up to 13 bar. Operating temperature: up to +50°C. Condensate drain: manual / semi-automatic (RMSA). Recommended flow: 200 Nl/min (at inlet pressure of 6 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe precise filter DEP series SYNTESI®, with end connections, is used to remove liquid or solid contaminants from compressed air with high accuracy. High filtration accuracy is achieved by using a special filtering element called a "coalescing cartridge." Size: SY1, SY2. Filtration degree: 0.01 µm - air purity class according to ISO 8573-1: 1-7-2. Supply pressure: up to 15 bar - size SY1, up to 13 bar - size SY2. Operating temperature: from -10°C to +50°C. Condensate drain: manual / semi-automatic (RMSA). Recommended flow: 460 l/min - size SY1, 620 l/min - size SY2 (at a pressure of 6.3 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLock preventing unauthorized adjustment of the pressure reducing valve settings or activation of the shut-off valve - for the Syntesi® series.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTwo-way branching module GA series G with internal BSP thread, used for air intake from any location of the FRL station. Supply pressure: up to 10 bar. Operating temperature: up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPA branching module, SKILLAIR® series, with end plates, is used for air intake from the FRL station at any stage of its preparation, regardless of the installation location. Size: 100, 200, 300. Supply pressure: up to 15 bar (13 bar - size 200, 300). Operating temperature: up to +50°C. Connection: BSP thread 1/4" ÷ 1".
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe distribution module is used when there is a need to draw air from the FRL Newdeal unit at any stage of its preparation, e.g., reduced air, oil-free air, or supply air. Size: 1/4", 3/8", 1/2", 3/4", 1". Connection: BSP female thread 1/8" for 1/4", BSP female thread 1/4" for 3/8" to 1/2", BSP female thread 1/2" for 3/4" to 1". Working pressure: up to 18 bar. Operating temperature: from -10°C to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBranching module - coupling mounted between two any SYNTESI® modules, used for independent air intake. Version 2 - two-way, has two connections (upper and lower). Size: SY1, SY2. Operating pressure and temperature: dependent on the SYNTESI® modules it is connected to. Flow: 1550 l/min - 1/8" (SY1), 7000 l/min - 3/8" (SY2), (at an inlet pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe branching module is a coupling mounted between any two SYNTESI® modules, used for independent air intake. It has 4 sockets for terminal connections on each plane. Size: SY1, SY2. Operating pressure: up to 15 bar for SY1 and up to 13 bar for SY2. Operating temperature: from -10°C to +50°C. Flow rate: 500 - 2000 l/min - SY1, 1500 - 4500 l/min - SY2, (at an inlet pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMembrane-type pressure reducing valve with an integrated pressure gauge in the knob, ideal for panel mounting. It features an atmospheric air vent. High accuracy in maintaining outlet pressure. Available components for panel mounting (EW-367K33). Material: zinc and aluminum alloy. Size: 3/8”. Supply pressure: up to 25 bar. Operating temperature: from -10°C to +90°C. Connection: 3/8" BSP female thread. Flow rate 1000 l/min (at an inlet pressure of 8 bar and Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA pneumatic lubricator is a simple and widely used solution that ensures proper lubrication with an oil mist for actuating devices in pneumatic systems. The oil suction process occurs due to the pressure drop created in the Venturi nozzle. The amount of oil droplets introduced into the air stream is regulated by an adjustment needle. There are auxiliary connections on the rear and front surfaces of the lubricator for connecting a manometer, pressure sensor, or for additional air intake. Size: SY1, SY2. Tank capacity: 60 cm³ - SY1, 130 cm³ - SY2. Supply pressure: up to 15 bar for SY1 and up to 13 bar for SY2. Operating temperature: from -10°C to +50°C. Connection: BSP 1/8" to 3/8" for SY1 and BSP 3/8" to 1" for SY2. Flow rate: 1600 l/min - 1/8", 3000 l/min - 1/4", 3650 l/min - 3/8", 6100 l/min - 1/2", 3/4", 1" (at an inlet pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCompressed air lubricator with polycarbonate tank, ensures proper lubrication of devices in pneumatic installations with oil mist. Size: DN6. Installation: vertical. Housing material: brass. Sealing: NBR. Tank capacity: 40 cm³. Supply pressure: up to 16 bar. Operating temperature: from -10°C to +50°C. Connection: G 1/4" BSP. Flow rate: 1160 l/min (at inlet pressure 6 bar Δp = 1 bar). Weight: 400 g.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe soft start valve is used to fill the working system with compressed air, operating in a two-stage manner. The application of a control signal causes the shut-off valve to open and air to flow through the throttling valve. Once the output pressure reaches approximately 40 to 60% of the supply pressure, the valve is overridden, allowing air to flow through the full cross-section from the inlet to the outlet. Removing the control signal causes the supply valve to close and the working system to vent. The soft start valve is used in installations where there is a need to protect powered actuators from sudden aeration, which can generate shock loads affecting the structural elements of machines. Excessive air intake from the outlet during the initial aeration of the working system can disrupt the operation of the valve, preventing it from fully opening. Size: SY1, SY2. Connection: BSP 1/8" to 1". Supply pressure: 3 - 10 bar. Additional outlet connection: BSP 1/8" for size SY1, BSP 1/4" for size SY2, at the front and rear. Operating temperature: from -10°C to +50°C. Nominal flow: depending on size from 1250 l/min to 4800 l/min (at pressure 6.3 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSoft start valve, used for the safe introduction of air into the pneumatic system, protecting actuators from sudden pressure increases. In the version with electric control, without pilot pressure, air flows from the inlet connection to the outlet through a needle valve. Upon receiving an external control signal, electrical, the valve is overridden and air flows through the full cross-section of the valve. The valve does not vent the pneumatic system. Size: 100. Supply pressure: up to 10 bar. Operating temperature: up to +50°C. Flow: 2000 l/min (at an inlet pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSoft start valve, used for the safe introduction of air into the pneumatic system, protecting actuators from sudden pressure increases. STD valve: opens automatically when the outlet pressure reaches approximately 50% of the inlet pressure. Pneumatic control valve: without pilot pressure, air flows from the inlet connection to the outlet through a needle valve. Upon receiving an external control signal, pneumatic, the valve is overridden and air flows through the full cross-section of the valve. The valve does not vent the pneumatic system. Size: 100. Supply pressure: up to 15 bar. Operating temperature: up to +50°C. Flow: 2000 l/min (at an inlet pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsManual shut-off valve V3V, NEW DEAL series, separates the working system from the supply air. It features a triple locking mechanism, and the valve opens by pressing a button. The mushroom system used ensures high flow rates. Connection: GW BSP 1/4" to 1/2". Supply pressure: up to 18 bar. Operating temperature: up to +50°C. Nominal flow: 1500 l/min for 1/4" connection, 2900 l/min for 3/8" and 1/2" connections (at an inlet pressure of 6 bar and Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsElectric shut-off valve V3V, SKILLAIR® series, with end plates, is used to separate the working system from the supply air. It is a normally closed, three-way valve. In the closed position, it cuts off the supply air while simultaneously venting the system, making it particularly useful during maintenance work. Size: 100, 200. Supply pressure: up to 10 bar. Operating temperature: up to +50°C. Connection: GW BSP 1/4" to 3/8". Flow rate: 1650 l/min (at inlet pressure 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsManual shut-off valve V3V with lock, SKILLAIR® series, with end plates. Its purpose is to separate the working system from the supply air. It is a normally closed, three-way valve. In the closed position, it cuts off the supply air while simultaneously venting the system, making it particularly useful during maintenance work. In the resting position (closed), it can be locked with a padlock, which secures the valve against activation by unauthorized persons. Size: 100, 200, 300. Supply pressure: up to 15 bar (depending on size). Operating temperature: up to +50°C. Nominal flow: depending on size up to 4700 l/min (at an inlet pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPrecision pressure reducing valve series GS with quick venting, designed to maintain a set pressure at a constant level and to quickly discharge any excess pressure from the pneumatic system. Intended for applications requiring high accuracy, e.g., for use with actuators with a reduced friction coefficient typically used as pneumatic springs with a constant characteristic. High flow through the valve during aeration and venting of the system and high setting precision are ensured by two identical and opposing regulating valves, separate for the supply and outlet connections. Installation in the system is done using mounting brackets or directly, using mounting holes located in the valve body. Output pressure range: 0÷2, 0÷4, 0÷8 bar. Supply pressure: up to 10 bar. Working medium: filtered 10 µm compressed air, non-oiled. Drain valve sensitivity: 30 mbar. Operating temperature: from -10°C to +50°C. Connection: BSP 1/8" and 1/4". Additional connection for pressure gauge: BSP 1/8". Flow: 1200 l/min - 1/8", 1380 l/min - 1/4" (at input pressure 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPiston-type pressure reducing valve RP, characterized by resistance to harsh working conditions, remotely controlled by external pressure (pilot), intended for the NEW DEAL series. Possibility of wall mounting using holes in the body. Size: 3/8", 1/2". Output pressure range: dependent on the pilot controlling the reducer. Supply pressure: up to 18 bar. Operating temperature: up to +50°C. Connection: BSP female thread 3/8", 1/2". Pressure gauge connection: BSP female thread 1/8". Flow rate: 4500 l/min (at input pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure piston-type pressure reducing valve with manometer, used for regulating working pressure and ensuring proper operation in the connected installation, regardless of changing medium consumption. Size: DN12. Housing material: brass. Output pressure range: 0.5÷12, 1÷20, 2÷35, 3÷50 bar. Supply pressure: up to 60 bar. Operating temperature: from -10°C to +90°C. Connection: BSP 1/4", 3/8". Manometer dial diameter: Ø63. Flow rate: 2000 l/min - 1/4", 2500 l/min - 3/8" (at input pressure 20 bar Δp = 4 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsREG pressure reducing valve, SKILLAIR® series, without end plates, is used for regulating operating pressure, ensuring proper device operation. Size: 100, 200, 300. Output pressure range: 0÷2, 0÷4, 0÷8, 0÷12 bar. Supply pressure: up to 15 bar (13 bar - size 200, 300). Operating temperature: up to +50°C. Connection: BSP 1/4" to 1". Pressure gauge connection: BSP 1/8". Flow rate: 1600 l/min - series 100, 3500 l/min - series 200, 7000 l/min - series 300 (at input pressure 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRegulating valve with lock REG type piston, characterized by resistance to harsh working conditions, intended for the NEW DEAL series. Possibility of wall mounting using holes in the body. It has a stem with a hole located in the upper part of the adjusting knob. When the knob is in the locked position, there is an option to place a padlock in the hole, preventing changes to the reducer settings. The set includes a padlock and 2 keys. Size: 3/8", 1/2". Output pressure range: 0÷4, 0÷8, 0÷12 bar. Supply pressure: up to 18 bar. Operating temperature: up to +50°C. Connection: GW BSP 3/8", 1/2". Pressure gauge connection: GW BSP 1/8". Flow: 2500 l/min (at input pressure 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSeries REG pressure reducing valve, SYNTESI® series, without end connections, is used to regulate working pressure and maintain it at a constant level, ensuring proper operation in the connected installation, regardless of the changing consumption of the medium. The valve uses a shaped diaphragm instead of a flat diaphragm, which provides higher nominal flow values due to a greater diaphragm stroke, as well as greater sensitivity and response speed to changes in settings, by reducing static and kinetic friction of components and increasing accuracy in maintaining the set output pressure with changes in flow and supply pressure values. The "push-lock" mechanism allows the knob to be locked in any position by pressing it. The locking plate enables the installation of a padlock to prevent unauthorized changes to the output pressure setting. They are designed to draw air from connections at the front and back of the body, which can be used to connect a pressure gauge, pneumatic-electric relay, or plug couplings, with direct connection of input and output connections. This allows for the installation of any number of pressure reducing valves next to each other, supplied from a single source, independently adjustable. Size: SY1, SY2. Output pressure range: 0÷2, 0÷4, 0÷8, 0÷12 bar. Supply pressure: up to 15 bar, depending on size. Operating temperature: from -10°C to +50°C. Additional connection for pressure gauge or couplings: BSP 1/8" for size SY1, BSP 1/4" for size SY2. Flow: 500 l/min - size SY1, 1000 l/min - size SY2 (at input pressure 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSeries REG pressure reducing valves, SKILLAIR® series, without end plates, are used for regulating working pressure, ensuring proper operation of devices. They can be installed in series and supplied with the same pressure. Each valve can have a different output pressure setting, independent of the settings of other valves. The output air is taken from the pressure gauge connection (1/8”). Size: 100. Output pressure range: 0÷2, 0÷4, 0÷8, 0÷12 bar. Supply pressure: up to 15 bar. Operating temperature: up to +50°C. Pressure gauge connection: GW BSP 1/8". Flow rate: 950 l/min (at input pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSeries REG pressure reducing valves, SKILLAIR® series, with end plates, are used to regulate working pressure, ensuring the proper operation of devices. They can be installed in series and supplied with the same pressure. Each valve can have a different output pressure setting, independent of the settings of other valves. The output air is taken from the pressure gauge connection (1/8”). Size: 100. Output pressure range: 0÷2, 0÷4, 0÷8, 0÷12 bar. Supply pressure: up to 15 bar. Operating temperature: up to +50°C. Connection: BSP 1/4" or 3/8". Pressure gauge connection: BSP 1/8". Flow: 950 l/min (at an inlet pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSet F + D series SKILLAIR® with a high degree of reliability consists of a filter and a fine air filter. The purpose of the set is to purify the air supplied by the compressor and to remove with high accuracy liquid and solid contaminants contained in the compressed air. Size: 100, 200, 300. Supply pressure: up to 15 bar, depending on size and type of discharge. Filtration degree: filter - 5 µm, fine filter - 99.97% at 0.01 µm. Connection: GW BSP 1/4" to 1". Condensate discharge: manual / semi-automatic (RMSA), automatic (SAC, RA). Operating temperature: up to +50°C.
