Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, very flexible and pliable, resistant chemical two-layer hose intended for discharge most aggressive chemical vapours, gases, dusts and fibres (non-abrasive). very good resistance chemical on aggressive chemicals thanks to internal layer film PTFE. W version standard inner Layer white natural PTFE meets requirements industry food (FDA). W version antistatic EL black inner Layer PTFE is electrically conductive (R ≤10 6 Ω). hose is characterized high compressibility - for 1:6, strong design resistant on vibration, stretching and tearing, resistance on impacts thanks to outer spiral. resistant to radiation UV, ozone and aging. used in industry chemical and food. Also available with a stainless steel spiral (from 80 mm diameter). Assembly of the hose on connectors with bridge clamps (lewo-handed). Checking chemical resistance - the chemical resistance table for PTFE (preliminary selection), confirmation of resistance and conditions of use - by Tubes International. length standard: od 2 for 10 m. Material hose Inner layer: white foil PTFE PTFE - version standard PETEF, black conductive foil PTFE PTFE - version antistatic PETEF EL. Material hose Outer layer: fabric polyethylene coated polyethylene (PE). Reinforcement: outer spiral with wire and sheet steel galvanized. Operating temperature: od -40°C up to +80°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose delivery for plastering. Layer inner with rubber o sound resistance to abrasion (70±5 mm 3 acc. to ISO 4649 / DIN 53516). The antistatic inner and outer layer prevents the accumulation of electric charges. multiple Reinforcement cord synthetic ensures high strength pressure. Layer outer resistant abrasion, conditions atmospheric and ozone. used for spraying wet mortar: cement, plaster and gypsum in works construction. commonly used for units plastering. Mounted with special plastering ends. hose NIAGARA LIGHT to version economical o slightly thinner wall (marked letter "L" on the end index). length standard: 60 m and 40 m version LIGHT (or 120 m - contact with Tubes International). Inner layer: black rubber SBR/NR. Reinforcement: cord synthetic. Outer layer: black rubber SBR/NR. Working pressure: 40 bar. Operating temperature: od -40°C up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA strong suction-delivery hose intended for conveying dry abrasive substances. Layer inner with white, smooth, resistant to abrasion rubber (80 mm 3 acc. to ISO 4649, formerly DIN 53516), compliant with requirements FDA 21 CFR 177.2600 for contact with food. Two built-in copper wires which, after earthing (or connection to an earthed end), discharge electric charges. Layer outer resistant to conditions atmospheric and ozone. A hose intended for conveying dry food substances: grain, sugar, powders, feed, granulates, etc. and other abrasive substances, e.g. PVC granulate, for which a white, non-staining inner layer is required. It is not intended for work in ATEX explosion-hazard zones. Standards and requirements: Food industry, food contact: 1935/2004/EC, 2023/2006/EC (GMP), BfR XXI kat.4. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: white rubber NR/SBR. Reinforcement: cord synthetic, steel spiral. Outer layer: black EPDM rubber. Working pressure: from 6 bar to 8 bar, depending on the diameter hose. Vacuum: 0.9 bar. Operating temperature: -30°C up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose intended for discharge dusts, sawdust, chips, light bulk materials o properties abrasive. used in industry wood, construction, food. resistant to ozone. Wall thickness measured between the spiral. available other diameter in the scope 30 ÷ 400 mm. Hose material: transparent polyurethane. Reinforcement: copper-plated spiral with wire steel. Operating temperature: od -40°C up to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, very flexible and pliable, resistant chemical hose intended for discharge aggressive chemical vapours, gases, dusts and fibres. used mainly in industry chemical and m.in. at removal asbestos. very good resistance chemical on solvents and other aggressive vapours. resistant to hydrolysis and corrosion biological. Contains no halogen compounds or plasticisers. is characterized high compressibility - for 1:8, strong design, resistance on impacts thanks to outer spiral. Also available with a stainless steel spiral (from 80 mm diameter). Assembly of the hose on connectors with bridge clamps (lewo-handed). Checking chemical resistance - the chemical resistance table for polyethylene (preliminary selection), confirmation of resistance and conditions of use - by Tubes International. length standard: od 2 for 10 m. Hose material: fabric polyethylene coated polyethylene (PE). Reinforcement: outer spiral with wire and sheet steel galvanized. Operating temperature: od -40°C up to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose delivery for pneumatic conveying dry substances abrasive. special The design hose o exceptional resistance to abrasion. Layer inner smooth, with black antistatic rubber natural with embedded in it balls with corundum (Al 2 O 3 – oxide aluminum), material ceramic o high hardness. built-in cable copper, which po earthing (connection with earthed fitting) discharges charges electrical. Layer outer with black, antistatic (R 6 Ω) rubber SBR / NR resistant to abrasion and aging. hose intended for conveying dry strong abrasive substances: e.g. dry cement, carbon, dust carbon, coke, solid fuels with raw materials secondary, minerals, powders ceramic, shot steel, fragments glass, fibre glass. used in smelters, coking plants, power plants, cement plants, mines, smelters glass, factories materials abrasive and materials insulating. advantage is large service life hose in these use – traditional hose with rubber resistant to abrasion can work e.g. only several dni, a hose ALUSPHERE in these same conditions even several months. Inner layer: balls ceramic embedded in black rubber NR. Reinforcement: cord synthetic. Outer layer: black rubber SBR/NR. Working pressure: 12 bar. Operating temperature: od -30°C up to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery light and extremely pliable hose rubber, for extraction dusts, powders and other lightly abrasive materials. Layer inner smooth, with abrasion-resistant rubber o wall thickness 2.4 mm. Layer outer corrugated, resistant to abrasion and conditions atmospheric. thanks to reinforcement spiral steel resistant to kinking and vacuum for 0.6 bar. Not is intended for use with overpressure, designed only for vacuum (extraction). Due to lightness and exceptional as on hose rubber flexible perfectly works in systems vacuum cleaning in industry, on example in quarries or smelters. It has a copper anti-electrostatic wire for discharging electric charges. Inner layer: black rubber natural. Reinforcement: cord synthetic, steel spiral. Outer layer: black rubber SBR. Vacuum: for 0.6 bar. Operating temperature: od -40°C up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose polyurethane, reinforced spiral with wire steel, intended for discharge and conveying bulk materials, dusts and sawdust. resistant to ozone. Hose material: transparent polyurethane. Reinforcement: spiral with galvanized wire steel. Operating temperature: od -40°C up to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose delivery for sandblasting. thick Layer inner with rubber o very sound resistance to abrasion (50±5 mm 3 acc. to ISO 4649 / DIN 53516). The antistatic inner and outer layer prevents the accumulation of electric charges. Used for sand and steel shot in abrasive blast treatment of steel structures, castings, concrete surfaces, etc.. commonly used in industry metal and shipbuilding. Mounted with special sandblasting ends. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black rubber NR/SBR. Reinforcement: cord synthetic. Outer layer: black rubber NR/SBR. Working pressure: 12 bar. Operating temperature: od -40°C up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong and thick hose suction-delivery intended for conveying bulk substances abrasive e.g. powders, cement, granulates, abrasive etc. externally Serrated, inside smooth. Layer inner with resistant to abrasion polyurethane. is characterized good resistance on impacts external and heavy conditions use. resistant to radiation UV and low temperatures. hose has arranged next to spiral cable copper coated polyurethane, which po earthing (or connection with earthed fitting) discharges charges electrical. used in installations industrial, for handling, in construction and industry shipbuilding. Inner layer: blue polyurethane. Reinforcement: rigid-PVC spiral. Hose material: grey and violet PVC. Working pressure: from 5 bar to 6 bar - depending on the diameter hose and temperatures. Vacuum: for 0.9 bar. Operating temperature: od -20°C up to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, smooth, flat rollable hose intended for discharge bulk materials. especially used in installations exposed on vibration and damage mechanical. is suitable for contact with food and in industry pharmaceutical being free of taste and odour, in the scope conformity with requirements FDA (21CFR177.2600). Not is subject to hydrolysis and is resistant to microbes. resistant also on oils mineral, aging, factors atmospheric, ozone, UV and many substances chemical. Hose material: transparent polyurethane. Working pressure: from 0.135 bar to 1.03 bar, depending on the diameter hose. Operating temperature: -40°C up to +90°C (momentarily +125°).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose delivery intended for transport products petrochemical o content compounds aromatic up to 50%, fuels, for systems oil, lubrication, etc. Layer outer resistant to action fuels, oils, conditions atmospheric. Inner layer: black NBR rubber. Reinforcement: a synthetic braid. Outer layer: black NBR rubber/PVC. Working pressure: 10 or 20 bar. Operating temperature: od -20°C up to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery light and pliable hose suction-delivery intended for conveying liquid products petrochemical containing up to 30% compounds aromatic (except products based on esters). Layer outer flame-retardant, made in accordance with the standard ASTM C 542, resistant to abrasion, oil, ozone and conditions atmospheric. Inner layer: black NBR rubber. Reinforcement: cord synthetic, two spirals steel. Outer layer: black rubber CR. Working pressure: 5 bar. Vacuum: 0.5 bar. Operating temperature: od -30°C up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong hose delivery intended for hot oil in installations hydraulic under pressure up to 40 bar. Layer outer made is with blue rubber synthetic, self-extinguishing (in accordance with requirements MSHA), resistant to conditions atmospheric. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black synthetic rubber. Reinforcement: a synthetic braid. Outer layer: blue self-extinguishing synthetic rubber. Working pressure: 40 bar. Operating temperature: od -30°C up to +130°C (momentarily up to +150°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong and pliable hose suction - delivery for low-pressure parts installations hydraulics power, based on the requirements of the SAE J517 100 R4 standard. used in particular as hose suction and return oil. intended primarily for liquids hydraulic based on oil mineral and some synthetic liquids hydraulic. can be also used for liquids hydraulic based on water and for water at limiting temperatures up to +70°C. is suitable for conveying many liquid products industry petrochemical o low content compounds aromatic. Not recommended for gasoline, oil drive and oils based on esters phosphate. Layer inner with black, smooth, oil-resistant rubber synthetic. Reinforcement consists of layer cord synthetic and steel spiral ensuring high resistance to vacuum and very good flexible hose without kinking. Layer outer with black rubber synthetic, resistant to abrasion, conditions atmospheric and light oiling. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black synthetic rubber. Reinforcement: cord synthetic, steel spiral. Outer layer: black synthetic rubber. Working pressure: from 2 bar to 21 bar - depending on the diameter hose. Operating temperature: od -40°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight and flexible hose delivery intended for conveying liquid products industry petrochemical, containing up to 30% compounds aromatic. It has a copper wire ensuring electrical continuity between the hose ends. Layer outer resistant to abrasion, oil and conditions atmospheric. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black NBR rubber. Reinforcement: cord synthetic. Outer layer: black synthetic rubber. Working pressure: 10 bar. Operating temperature: od -20°C up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA strong suction-delivery hose intended for unleaded petrol, diesel oil and liquid fuels containing up to 50% aromatic compounds. Used in industry and transport for conveying and handling petrochemical products, in road tankers, at road and rail fuel unloading and loading terminals. Layer inner with black, smooth, antistatic (R ≤ 10 6 Ω) rubber NBR (NBR1). Reinforcement layers high-strength cord and spiral steel. It has two copper wires ensuring electrical continuity between the hose ends – provided they are correctly connected to the ends. Layer outer with black, antistatic (R ≤ 10 6 Ω) rubber synthetic, self-extinguishing, resistant to abrasion, oil, ozone and conditions atmospheric. Resistance through the hose wall R ≤ 10 9 Ω (type M/T). compliant with standards EN12115:11 (16 bar), EN 1761(10 bar), ISO 2929 (10 bar), TRbF. Certified for Ex explosion-hazard zones (ATEX). excellent resistance to action products petrochemical, strong The design and properties antistatic both layer internal and outer, built-in cable antistatic, recommend this hose for demanding applications, also in explosion-hazard zones. In every case, however, use in an explosion-hazard zone (ATEX) should be preceded by a risk analysis carried out by a specialist. A version without a wire (type Ω/T) is available on special order.. Inner layer: black, smooth NBR rubber. Reinforcement: cord synthetic, steel spiral. Outer layer: black synthetic rubber. Working pressure: 16 bar. Operating temperature: od -30°C up to +90°C (momentarily up to +110°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong and flexible, resistant to abrasion hose suction-delivery intended for pressure conveying oils and fuels. special blend PVC, PU and NBR ensures high resistance to oil drive, biodiesel, and blue oil (fuel used in maritime navigation). Reinforcement spiral with galvanized wire steel, embedded in layer internal, PVC, ensures good resistance to vacuum and kinking hose. smooth Layer inner reduces losses flow. thanks to reinforcement a braid hose has high pressure working and small deformation under pressure. used in distribution, refuelling and handling oils and fuels, e.g. in tankers automotive for refuelling oil heating in domestic systems heating. hoses o diameters 76 ÷ 102 mm have external layer polyurethane (increasing significantly resistance to abrasion) and copper cable antistatic. Inner layer: black PVC / PU / NBR. Reinforcement: steel spiral, a polyester braid. Outer layer: black PVC / PU / NBR (diameter 19 mm ÷ 63 mm); black PU (diameter 76 mm and more). Operating temperature: od -25°C up to +60°C (working pressure depends on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose pressure for oils industrial, mineral, gasoline unleaded (EN 228:2017), oil drive (EN 590:2010), oil heating (DIN 51 603 1÷5). is suitable also for compressed air. Layer inner with black, smooth rubber NBR, antistatic R 6 Ω/m (EN ISO 8031:2009). Reinforcement a braid textile ensures factor safety 3.15 : 1. resistant to small vacuum for ok. 0.5 bar. Layer outer with black, smooth blend rubber NBR / EPDM resistant to oil, ozone, abrasion and conditions atmospheric. Inner layer: black NBR rubber. Reinforcement: textile braid. Outer layer: black NBR rubber/EPDM. Working pressure: 25 bar. Operating temperature: od -40°C up to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, soft hose rubber with external a braid of galvanized steel, intended for gasoline and oils petroleum-based such as e.g. oil drive, heating, lubricating. mounted in installations fuel and oil small vehicles and equipment industrial. It can also be used for water, cooling liquids, non-oxidising detergents, air. Based on the requirements of the DIN 73379 standard. Layer inner with smooth, black rubber NBR. The external reinforcing braid of galvanized steel provides high pressure resistance. W braid black band marking. The maximum working temperature depends on the medium: for petrol, unleaded petrol, fuels up to 50% aromatic hydrocarbon content: +40°C; for diesel oil (diesel): +80°C; for water and cooling liquids based on ethylene glycol: +90°C; for air: +80°C; for liquid, non-oxidising detergents: +80°C. Hose material: black NBR rubber. Reinforcement: external braid wire of galvanized steel. Working pressure: from 10 bar to 20 bar, dependent od diameter hose. Operating temperature: od -35°C up to +80°C (Maximum temperature dependent od medium).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, soft hose rubber with external a braid textile, intended primarily for installations fuel gasoline leaded and unleaded and oil drive small vehicles (cars, motorcycles, mopeds, tractors garden) or equipment industrial. mounted e.g. between pump fuels a carburettor. Not is suitable for engines with system injection fuels. It can also be used for water, cooling liquids, non-oxidising detergents, air. Based on the requirements of the DIN 73379 standard type B (03/1982). Layer inner with smooth, black rubber NBR. The external braid vulcanised with rubber reinforces the hose and protects against contact with hot element. The maximum working temperature depends on the medium: for petrol, unleaded petrol, fuels up to 50% aromatic hydrocarbon content: +40°C; for diesel oil (diesel): +80°C; for water and cooling liquids based on ethylene glycol: +90°C; for air: +80°C; for liquid, non-oxidising detergents: +80°C. Hose material: black NBR rubber. Reinforcement: external black textile braid. Working pressure: 10 bar. Operating temperature: od -35°C up to +120°C (momentarily), Maximum temperature use dependent od medium.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery pliable and flexible hose for gasoline unleaded and oil drive cars passenger, trucks and tractors. It can be used in compartment engine trucks. Layer inner with black, smooth rubber NBR highly resistant to fuel (resistance to oil: RMA class A), suitable for use with greater fuels automotive (standard oil drive B7 (EN590:2017), biodiesel B20, B100, standard gasoline unleaded E5 (EN228:2017), E10, E85 and E100 - 100% ethanol). Reinforcement strength a braid textile ensures Safety factor 4:1. Layer outer with black, smooth, high quality rubber synthetic resistant to oil, ozone and conditions atmospheric. commonly used hose fuel for vehicles automotive. compliant with standards SAE J30R2 and SAE J30 R6. Inner layer: NBR rubber. Reinforcement: textile braid. Outer layer: black synthetic rubber. Working pressure: 12 bar. Operating temperature: od -40°C up to +100°C externally up to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose rubber CODAN 3106 intended for gasoline leaded and unleaded. used for connections e.g. carburettor with pump fuels in cars, motorcycles, mopeds, tractors garden, etc. Not is suitable for engines with system injection. Based on the requirements of the DIN 73379 standard type B (03/1982). Layer inner with smooth, black blend rubber NBR / PVC. The external braid vulcanised with rubber reinforces the hose and protects against contact with hot element. It can also be used for water, cooling liquids, non-oxidising detergents, air. The maximum working temperature depends on the medium: for water and cooling liquids based on ethylene glycol: +90°C, for air: +80°C, for liquid, non-oxidising detergents: +80°C, for diesel oil (diesel): +80°C, for petrol, unleaded petrol, fuels up to 50% aromatic hydrocarbon content: +40°C. Hose material: black NBR rubber/PVC. Reinforcement: external textile braid (black polyester). Working pressure: from 5 bar to 13 bar, depending on the diameter hose. Operating temperature: od -30°C up to +100°C (momentarily), Maximum temperature use dependent od medium.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh quality, multilayer hose fuel, Based on the requirements of the DIN 73379-3E standard (11/97). design: Layer inner with resistant chemical and temperature-wise Viton (FPM), Layer intermediate with epichlorohydrin (ECO), resistant to temperature and strength braid with fibers aramid, Layer outer with epichlorohydrin (ECO) – resistant to temperature, ozone, microcracks. Layer inner made of Viton ensures excellent resistance chemical on action hydrocarbons, products petrochemical a also many aggressive substances chemical and additives used for fuels, also in elevated temperatures use. especially recommended for biofuels based on esters methyl acids fatty (FAME) e.g. biodiesel B10, B20, B100. resistant to ester methyl acids fatty oil rapeseed (RME). It can be used for biopetrols containing alcohol ethyl e.g. E10, E100. resistant to esters phosphate (consists ofce also additives for fuels liquid). It can be used also for ordinary oil drive, gasoline, oils mineral. recommended for demanding applications under relative to high cleanliness fuels, resistance to temperature and aging. is characterized low permeability hydrocarbons through wall hose. Inner layer: rubber FPM (Viton). Intermediate layer: rubber epichlorohydrin (ECO). Reinforcement: textile braid aramid. Outer layer: rubber epichlorohydrin (ECO). Working pressure: 10 bar. Operating temperature: od -40°C up to +125°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible, suction-delivery hose intended for conveying liquid products industry petrochemical, containing up to 50% compounds aromatic. Layer inner antistatic R 6 Ω. It has a copper wire ensuring electrical continuity between the hose ends and discharge charges electrostatic. excellent for systems transfer and thanks to external corrugation for applications demanding small radius bending. Layer outer resistant to abrasion, oils mineral, ozone, aging, conditions atmospheric and momentary contact with carbon. used for tankers fuel and special cars for cleaning sewers. Inner layer: black NBR rubber. Reinforcement: a synthetic braid, spirals steel. Outer layer: black synthetic rubber. Working pressure: from 10 bar to 16 bar - depending on the diameter hose. Vacuum: 0.9 bar. Operating temperature: od -30°C up to +80°C (momentarily up to +120°C depending on kinds medium).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong hose suction - delivery intended for conveying and handling hot liquid asphalt, tar, products bituminous. used for loading and unloading tankers road, railway, in plants masses bituminous and in ports. Inner layer: black blend polyacrylic. Reinforcement: cord with wire steel, steel spiral. Outer layer: black synthetic rubber. Working pressure: 10 bar. Operating temperature: od -15°C up to +200°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose suction-delivery o extreme flexibility intended for conveying liquid products industry petrochemical, containing up to 60% compounds aromatic. appropriate for use in tankers automotive for transport oil drive, ethanol, gasoline, oils. Layer inner with black, smooth rubber Chemigum ® (NBR, resistance to oil: RMA class A). Reinforcement cord synthetic and two spirals with wire steel. Layer outer, deep corrugated, with black rubber synthetic Chemivic ® (NBR/PVC), resistant to action substances petrochemical, oils and greases and on abrasion. It has a copper wire ensuring electrical continuity between the hose ends – under a condition correct connection for ends. thanks to external corrugation, hose is extremely pliable, a for its bending needed is small force. its minimal radius bends, equal is diameter internal hose. external serrated reduces also resistance pulling hose po ground, a light The design facilitates operating a hose. Inner layer: black NBR rubber. Reinforcement: cord synthetic, spirals steel. Outer layer: black synthetic rubber Chemivic®. Working pressure: from 10 bar to 17 bar - depending on the diameter hose. Vacuum: 0.9 bar. Operating temperature: od -40°C up to +93°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, soft hose rubber with external a braid of galvanized steel, intended for gasoline and oils petroleum-based such as e.g. oil gear, heating, drive. mounted in installations fuel and oil small vehicles and equipment industrial. It can also be used for water, cooling liquids, non-oxidising detergents, air. Based on the requirements of the DIN 73379 standard. Layer inner with smooth, black rubber NBR. The external reinforcing braid of galvanized steel provides high pressure resistance. Hose material: black NBR rubber. Reinforcement: external braid wire of galvanized steel. Working pressure: from 6 bar to 25 bar - depending on the diameter hose. Operating temperature: od -35°C up to +90°C (momentarily 110°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose of special blend PVC intended for oils, fuels and other products petrochemical based on hydrocarbons. Material hose has elevated resistance to leaching plasticisers and retains its flexibility even po long use. withstands repeated bending, a simultaneously exhibits excellent resistance to aging. intended for installations fuel: pumps, burners, equipment heating, installations oil. Not is suitable for hydrocarbons aromatic (benzene, toluene, xylene etc.). Not recommended for gasoline, in particular for intensive use or more demanding applications (in such case consider hose TECHNOBEL PU). It can be used for some products chemical: diluted acids, bases and alcohols. smooth surface inner and outer hose and translucent wall enable visual control flow. used widely in industry automotive, assembly shops, industry plastics, industry wood, workshops automotive, agriculture, forestry and services municipal. Inner layer: greenish transparent PVC. Reinforcement: a synthetic braid. Outer layer: greenish transparent PVC. Working pressure: from 8 bar to 13 bar, depending on the diameter hose. Operating temperature: od -15°C up to +60°C (working pressure depends on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose suction-delivery intended for conveying liquid products industry petrochemical. It can be used for oil drive and gasoline. standard version CARACAS recommended is for fuels o content up to 30% hydrocarbons aromatic, whereas version CARACAS 50, at more aggressive fuels (up to 50% compounds aromatic). It has a copper wire ensuring electrical continuity between the hose ends. excellent for systems transfer. Layer outer resistant is on abrasion, oil, ozone and conditions atmospheric, a thanks to corrugation, hose is very pliable and flexible – its minimal radius bends is only 2.5 x Diameter inner. is also light and easy in handling. excellent for systems transfer, tankers fuel in not very heavy external conditions use. Inner layer: black synthetic rubber. Reinforcement: a synthetic braid, spirals steel. Outer layer: black synthetic rubber. Working pressure: 6 bar. Vacuum: 0.6 bar. Operating temperature: od -20°C up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, extremely flexible and pliable, o small radius bends hose, PVC with inner layer with polyurethane (PU, polyester-polyurethane). thanks to sound resistance chemical polyurethane hose It can be used for gasoline, gasoline unleaded, oils, products petroleum-based and many solvents. is suitable for compressed air, also air oiled. Due to good resistance polyurethane on abrasion can be also used for conveying average abrasive powders or granulates. Not is whereas recommended for acids, bases and solutions water at temperatures above 40ºC. Not is suitable for hydrocarbons aromatic (benzene, toluene, xylene etc.). hose widely used we all fields industry. used also in agriculture for spraying agricultural (agents insecticides, pesticides, agents herbicides etc.). used for compressed air for tools pneumatic, guns for spraying, painting, sandblasting etc. Layer outer resistant to carbon and solvents in the molds mist with spraying. is suitable for mounting on drums. Inner layer: transparent polyurethane (PU). Reinforcement: a polyester braid. Outer layer: black PVC. Working pressure: from 12 bar to 20 bar, dependent od diameter hose and temperatures. Operating temperature: od -15°C up to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose with connections intended for fittings sanitary (heat and cold water). Widely used for connections in installations industrial, central heating and air-conditioning. resistant to action glycol o a concentration up to 35%. the connection made with brass, ferrules of steel stainless (AISI 304). has certificate hygienic and approval technical for use in construction. Available on both sides with a female BSP thread and with a thread internal and external BSP. Inner layer: black EPDM rubber (o elevated parameters). Reinforcement: external braid of steel AISI 304. Working pressure: 16 bar. Operating temperature: up to +110°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose for coolant in system 1/2" made with resistant to corrosion, solvents, oils and greases acetal, ensuring rigidity and resilient lines. intended for low-pressure conveying air, water, oils and other substances used in processes cooling and treatment metals. resistant to abrasion and vibration, ensures 100% stability position and not causes damage tools cutting. very easy in expansion modular The design. available length: 2x140 mm, 100 mm, 200 mm, 300 mm, 400 mm, 500 mm, 600 mm, 700 mm, 800 mm 900 mm and 1000 mm. Material: acetal. Working pressure: up to 2 bar. maximum Flow rate: 2173 l/h. Operating temperature: up to +76°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, very pliable, hose for conveying gasoline and oil drive, fire-resistant, for small vessels - recreational boats up to 24 m long. hose o pressure working 10 bar, manufactured method mandrel. Intended for fuel systems of stationary engines on ships, motorboats, yachts etc.. Suitable for unleaded petrol, petrol with up to 10% ethanol added (E10 petrol), diesel oil and diesel oil with 10% FAME esters added (B10 – biodiesel). Compliant with ISO 7840 type A1 (fireproof, fuel vapour permeability less than or equal to 100 g/m2/24 h), compliant with directive 94/25/EC, RINA certified, compliant with SAE 1527, USCG type A1. Layer inner with black, smooth rubber synthetic, resistant to oils and fuels up to 50% content hydrocarbons aromatic. Reinforcement layers synthetic cord, a for hose POSEIDON LL additional spiral steel. Layer outer with black, self-extinguishing rubber synthetic, resistant oil and conditions atmospheric (resistance to fire: ISO 7840 Annex A: hose filled fuel should withstand flame through 2.5 min). POSEIDON : hose POSEIDON is soft a hose delivery without reinforcement spiral steel. the manufacturer recommended assembly hoses POSEIDON o diameter over 19 mm in installations in sections straight or o gentle (high) radius bends. hose is used in particular in installations filling tanks fuels boats. On special order Available hose POSEIDON o smaller diameters 6, 8.10.13.16 and 19 mm, o pressure working 10 bar. POSEIDON LL : hose POSEIDON LL has additional Reinforcement spiral steel, co ensures resistance to vacuum and kinking. hose is very pliable, its minimal radius bends corresponds only three times diameter internal and can be easily installed in tight spaces compartment engine boats. universal use and high quality hose make, that is on readily and often used through manufacturers greater yachts motor. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black synthetic rubber. Reinforcement: cord synthetic (POSEIDON); cord synthetic, steel spiral (POSEIDON LL). Outer layer: synthetic rubber. Working pressure: 10 bar. Operating temperature: od -30°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight and flexible hose suction-delivery made of special, oil-resistant blend PVC. intended for conveying oils mineral and hydrocarbons and water industrial, sewage, liquid fertilisers, some chemicals – in particular tam, where elevated resistance PVC on carbon is required. Not is suitable for hydrocarbons aromatic (benzene, toluene, xylene etc.). It can be used for some products chemical – diluted acids, bases and alcohols. hose retains its flexibility even in sub-zero temperatures use, a its low weight and small radius bending ensure convenience and ease operation. Reinforcement spiral with hard PVC, resistant on impact, ensures very good strength on vacuum and kinking hose. smooth surface inner and outer. resistant to radiation UV, ozone, conditions atmospheric, abrasion. used widely in industry, agriculture, construction and road engineering. as hose reinforced spiral with hard PVC (without braid) is characterized a certain elongation under pressure, co should take into account in use, especially in temperatures above 40°C. Hose material: blue PVC. Reinforcement: spiral with white, hard PVC. Working pressure: from 2 bar to 5 bar - depending on the diameter hose. Operating temperature: od -25°C up to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose intended for water and non-corrosive media. used for installation sanitary, boilers, systems cooling. woven in in braid two red stripes inform o resistance hose on elevated temperature medium. Inner layer: non-toxic EPDM rubber. Reinforcement: braid of galvanized steel. Working pressure: from 6 bar to 15 bar, depending od diameter hose. Operating temperature: od -10°C up to +110°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose rubber reinforced a braid of galvanized steel ensuring high resistance pressure, perfectly works in installations oil small vehicles, installations fuel and equipment industrial. intended for gasoline and oils petroleum-based such as e.g. oil gear, heating czy drive. Layer inner made with rubber NBR in connection with a braid in the molds mesh (braid), make that hose is simultaneously soft and flexible. The maximum working temperature depends on the medium: for petrol, unleaded petrol, fuels up to 50% aromatic hydrocarbon content: +40°C; for diesel oil (diesel): +80°C; for water and cooling liquids based on ethylene glycol: +90°C; for air: +80°C; for liquid, non-oxidising detergents: +80°C. Inner layer: smooth, black NBR rubber. Reinforcement: external braid wire of galvanized steel. Working pressure: from 20 bar to 25 bar - depending on the diameter hose. Operating temperature: od -35°C up to +90°C (Maximum temperature use dependent od medium).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose intended for conveying under higher pressure oils industrial, mineral, oil drive (EN 590:2010), biodiesel and oil heating (DIN 51 603 1÷5). is suitable also for compressed air, liquids cooling based on glycol. Layer inner with black, smooth rubber NBR, antistatic R 6 Ω/m (EN ISO 8031:2009). Reinforcement strength a braid textile ensures factor safety 4 : 1. resistant to small vacuum for ok. 0.6 bar. Layer outer with black, smooth rubber SBR / NVC (NVC - blend NBR and PVC) is resistant to oil, ozone and conditions atmospheric. Inner layer: black NBR rubber. Reinforcement: a polyester braid. Outer layer: black rubber SBR/NVC. Working pressure: 40 bar. Operating temperature: od -45°C up to +100°C for fuels and oils, od -45°C up to +70°C for air.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSoft, flexible, extruded hose delivery for conveying gasoline and oil drive at low pressure, fire-resistant, for small vessels - recreational boats up to 24 m long. Intended for fuel systems of stationary engines on ships, motorboats, yachts etc.. Suitable for unleaded petrol, petrol with up to 10% ethanol added (E10 petrol), diesel oil and diesel oil with 10% FAME esters added (B10 – biodiesel). Compliant with ISO 7840 type A1 (fireproof, fuel vapour permeability less than or equal to 100 g/m2/24 h), compliant with directive 94/25/EC, RINA certified, compliant with SAE 1527, USCG type A1. Layer inner with black, seamless rubber synthetic, resistant to oils and fuels up to 50% content hydrocarbons aromatic. Reinforcement synthetic a braid textile. Layer outer with black, resistant to fire, seamless rubber synthetic, resistant to aging, greases, conditions atmospheric and temperature (resistance to fire: ISO 7840 Annex A: hose filled fuel should withstand flame through 2.5 min). Inner layer: black synthetic rubber. Reinforcement: a synthetic braid. Outer layer: black synthetic rubber. Working pressure: from 2.5 bar to 3.4 bar - depending on the diameter hose. Operating temperature: od -20°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA very strong delivery hose for aviation fuel, intended for direct pressurised refuelling of aircraft. It can also be used in fuel transfer operations in airport tankers – dispensers, in cases not requiring high vacuum. designed specially for kerosene (kerosene aviation - fuel for turbine engines aviation e.g. JET A1), gasoline aviation and fuels o content hydrocarbons aromatic up to 50%. It can be used on reels drum. Layer inner with black, smooth, antistatic rubber NBR. Reinforcement layers high-strength cord synthetic. Layer outer with black, antistatic, self-extinguishing rubber chloroprene (CR), resistant to abrasion, contact with carbon, conditions weather. The antistatic outer layer, in accordance with EN ISO 1825, provides the required low line resistance between the ends (10 3 Ω ‹ R ‹ 10 6 Ω, ISO 8031). Compliant with the requirements for aviation fuel hoses (type C/Ω) EN ISO 1825, EN 1361, BS 3158, EI 1529. Inner layer: black NBR rubber. Reinforcement: cord synthetic. Outer layer: black rubber CR. Working pressure: 20 bar. Operating temperature: od -30°C up to +70°C (for fuels aviation acc. to EN 1825).
