Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight and flexible flat-folded suction hose for water for fire pumps, without fittings. Used for fire, rescue, and forestry pumps. In addition to fire-fighting functions, widely used for water transfer in industry, construction, agriculture, and mining. The inner layer is smooth, resistant to mold and rot. The outer layer (braid) has high strength, with a polyurethane coating that does not retain dirt, increasing resistance to abrasion and contact with flames. Certifications: hoses compliant with the technical conditions of the MSWiA Regulation of April 27, 2010. Inner layer: smooth polyurethane. Reinforcement: polyester braid. Outer layer: red polyurethane coating. Working pressure: from 12 bar to 15 bar - depending on the hose diameter. Operating temperature: from -30°C to +70°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDurable, lightweight, and flexible suction and discharge hose designed specifically for the wine industry for heavier working conditions. Stronger than the LUISIANA hose, with a thicker wall. Hose for demanding applications. Intended for the transfer of water, beer, quality wines, and alcohols with a concentration of up to 20%, juices, beverages, and other food products. Free of phthalates. Not recommended for milk and its derivatives, oils, and fatty food substances. Reinforced with a hard PVC spiral, resistant to impact, provides very good resistance to vacuum and hose collapse. The transparent wall allows for easy visual monitoring of flow. The smooth inner surface reduces flow losses and ensures ease of cleaning. In applications not involving direct contact with food (in industry, construction, agriculture), it can be used: 1) for light chemicals, water, sludges, and wastewater, other liquids (without fats, oils, and hydrocarbons); 2) for air, vacuum transfer of dust, powders, granules, and other lightly abrasive bulk materials (non-fatty). Abrasiveness and potential static electricity issues should be considered. Standards and requirements: Food industry, contact with food - compliant with European requirements 1935/2004/EC and 10/2011/EU (simulative fluids A, B, and C), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: hard PVC spiral. Operating temperature: from -5°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsShell clamp made of a special high-strength material, allowing for easy assembly of hygienic connections to externally corrugated hoses of the EASY series (e.g., VINOFLEX EASY, MILLENNIUM EASY). The clamp features internal grooves precisely matched to the grooves of the EASY series hoses and is designed for the installation of hygienic connections (DIN, SMS, Triclover, and others) with a standard stub for the shell clamp. Working pressure: 10 bar. Material: high-strength plastic.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose designed for the removal of dust, wood shavings, and chips in the woodworking and furniture industry. Designed for CNC machines for wood and plastic processing: machining centers, vertical milling machines, milling plotters. The thick steel spiral coated with white PVC is corrosion-resistant, has good adhesion to the hose material, and provides high pressure parameters. Despite its strong construction, due to the optimally selected large spiral pitch, it is very flexible, bendable, and compressible. Particularly recommended for dust and chip extraction from rapidly moving working heads (CNC Router Dust Collection System). Resistant to microbes, hydrolysis, as well as oils and gasoline. Does not contain halogen compounds and plasticizers. Flame-retardant, compliant with the German standard DIN 4102 class B1. The hose can be treated as electrically conductive after grounding the spiral, in accordance with German industrial recommendations BGI 739-2. Installation on couplings with bridge clamps (right-handed). Other diameters in the range of 80 ÷ 600 mm available on special order. Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral coated with white PVC. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight, flat (at rest) industrial PVC suction hose. Thanks to the appropriately selected textile reinforcement with a polyester liner, it has good resistance to elongation. Designed for pressure transmission of water and other liquids. Widely used in agriculture, construction, shipbuilding, mining, etc. Standard roll length: 50 m or 100 m. Inner layer: black PVC. Reinforcement: polyester liner. Outer layer: blue PVC. Working pressure: from 2.5 bar to 8.5 bar - depending on the hose diameter and temperature. Operating temperature: from -5°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible suction and discharge hose designed for water-cooled exhaust systems of diesel engines in motorboats and yachts (free discharge of mixed exhaust gases and cooling water). Used in short sections between installation pipes. Inner layer resistant to exhaust gases. Outer layer resistant to fire and weather conditions. Has vacuum resistance. Compliant with Lloyds type certificate 99/00169 (E4), homologated by VTT according to Nordic Boat Standard MC9. Inner layer: black synthetic rubber CR. Reinforcement: synthetic cord, steel spiral. Outer layer: black, corrugated synthetic rubber CR. Burst pressure: ≥ 2 bar. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose intended for the transmission of cold drinking water (+23°C - approvals KTW, DVGW - Germany, WRAS - United Kingdom, D.M.174 - Italy) in industry and applications such as households, campgrounds, etc. The inner layer material is of food-grade quality, odorless and tasteless, ensuring the preservation of unchanged organoleptic properties of water. Free from phthalates. The outer layer is resistant to weather conditions. Standards and requirements: 1) General: EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) Approval for drinking water: UBA guideline, KTW, DVGW W270, D.M.174, WRAS according to BS 6920. 3) Food industry, contact with food: 1935/2004/EC, 2023/2006/EC (GMP); 21CFR 177.1520, BfR III, 10/2011/EU (inner layer). Inner layer: white plastomer. Reinforcement: synthetic braid. Outer layer: blue synthetic rubber. Working pressure: 20 bar. Operating temperature: -30°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, exceptionally flexible and bendable hose with good chemical resistance and UV radiation resistance. Resistant to hydrolysis and biological corrosion. Free of halogen compounds and plasticizers. Designed for the discharge of air, vapors, and gases. Used in the chemical industry and in ventilation and air conditioning systems in vehicles. Other diameters available in the range of 30 to 610 mm. Chemical resistance verification - chemical resistance table for polypropylene (preliminary selection), confirmation of resistance and application conditions - by Tubes International. Hose material: black soft polypropylene (PP). Wall thickness: 0.4 mm. Reinforcement: steel wire spiral. Operating temperature: from -20°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and pressure hose designed for the transfer of various light alcoholic products such as beer, wine, cider, and non-alcoholic beverages. The inner layer is completely free of phthalates, plasticizers, and animal-derived components, eliminating the risk of medium contamination and bacterial growth. The outer layer is abrasion-resistant with good aging resistance. Standards and requirements: 1) General EU 2015/863 (RoHS 3), EC 1907/2006 (REACH). 2) Food industry, food contact 1935/2004/EC, 2023/2006/EC (GMP). Inner layer compliant with FDA 21 CFR 177.2600, D.M. 21/03/73. Inner layer: white bromobutyl rubber (BIIR). Reinforcement: synthetic cord, steel spiral. Outer layer: red EPDM rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: -40°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose designed for compressed air. Recommended for pneumatic tools, compressors, hose reels, etc. Inner layer: black PVC. Reinforcement: polyester braid. Outer layer: beige PVC. Working pressure: 20 bar. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible hose designed for the transport of dust, wood shavings, chips, and lightweight abrasive bulk materials. Used in the woodworking, construction, and food industries. Ozone resistant. Wall thickness is measured between the spiral. Other diameters available in the range of 20 to 600 mm. Hose material: transparent polyurethane. Reinforcement: copper-plated (L/R version) or galvanized (L version) steel wire spiral. Operating temperature: from -40°C to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight suction and discharge hose designed for the transfer of milk and its products as well as food substances requiring the use of odorless and tasteless rubber. It contains no phthalates, plasticizers, or animal-derived products. The inner layer is resistant to commonly used cleaning agents and processes in the food industry. The special "CRUSH PROOF" hose construction allows the hose to return under pressure to its original shape after being accidentally run over, for example, by a forklift. The hose is lightweight and easy to handle. Particularly recommended for applications requiring a small bending radius. It retains its flexibility even at low temperatures. Standards and requirements: 1) General: EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) Food industry, food contact: EC 1935/2004, EC 2023/2006 (GMP). Inner layer compliant with D.M. 21/03/73, FDA 21 CFR 177.2600, BfR, RAL (German Institute for Quality Assurance and Certification). Inner layer: white, smooth NR/NBR rubber. Reinforcement: synthetic cord, plastic spiral. Outer layer: blue synthetic rubber. Working pressure: 6 bar. Operating temperature: from -30°C to +85°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, very flexible and bendable hose designed for the discharge of paint vapors, solvents, contaminated air, and dust in explosion hazard areas. Also used for air transmission in biogas plants. Permanently antistatic (R ≤108 Ω), compliant with technical standard TRGS 727 and standard TRAS120 for biogas plants. Resistant to hydrolysis and biological corrosion. Maintains flexibility at low temperatures, flame-retardant - meets the requirements of standard DIN 4102 B1 regarding the fire properties of building materials. Other diameters in the range of 20 ÷ 800 mm available on special order. Chemical resistance check - chemical resistance table for PVC (preliminary selection), confirmation of resistance and application conditions - by Tubes International. Hose material: polyester fabric impregnated with black PVC. Wall thickness: 0.4 mm. Reinforcement: steel wire spiral. Operating temperature: from -40°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal rubber hose intended for low-pressure applications: hydraulic oil, pneumatic and water installations. Widely used for cooling injection molds. Inner layer made of synthetic rubber resistant to high temperatures (mineral oil), outer layer resistant to weather conditions, abrasion, and oil. Not recommended for flammable hydraulic fluids based on phosphate esters. Safety factor 3:1. The hose is designed to work with self-clamping PUSH-ON type fittings. Inner layer: black synthetic rubber. Reinforcement: synthetic braid. Outer layer: blue or red synthetic rubber. Working pressure: from 14 bar to 24 bar - depending on the hose diameter. Operating temperature: up to +135°C (mineral oil), up to +80°C (water), up to +70°C (air).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible, resistant to kinks suction and discharge hose with a black corrugated outer layer, designed for the transmission of hot, dry air from the compressor to the tank installation. Ideal for situations where a small bending radius is required. Used in road tankers for transporting bulk materials: cement trucks, feed trucks, etc., as well as in other industrial installations. The outer layer is resistant to ozone and weather conditions. For a diameter of 90 mm available in 2 m sections with soft, spiral-free ends. Inner layer: white EPR rubber. Reinforcement: synthetic braid, steel spiral. Outer layer: black corrugated EPDM rubber. Working pressure: up to 10 bar. Operating temperature: from -40°C to +200°C (temporarily up to +240°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsClassic, high-quality, self-tightening rubber hose (PUSH-ON). For low-pressure hydraulic systems, pneumatic systems, and as a universal industrial hose for air, water, oils, greases, light chemicals, and cleaning fluids. Widely used in the automotive industry (no silicone used in hose production). The outer layer is resistant to weather conditions, abrasion, and oil. Flame resistance complies with MSHA 2G-14C/14 standard. Non-conductive (R > 1 MΩ/inch at 1000 V DC). Safety factor 4:1. The hose is designed to work with self-tightening PUSH-ON type fittings. Available in colors: black (BK), blue (BL), green (G), gray (GY), red (R), and yellow (Y). Inner layer: black synthetic rubber Chemivic™ (NBR + vinyl). Reinforcement: synthetic braid. Outer layer: black, blue, green, gray, red, or yellow synthetic rubber. Working pressure: 20 bar. Operating temperature: from -40°C to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible and bendable, chemically resistant and flame-retardant hose designed for use in air conditioning, ventilation, and heating systems. For the extraction and transmission of hot air, chemically aggressive vapors, exhaust gases, and gases in ventilation and heating systems. It has resistance to UV, ozone, and weather conditions. Used in vehicle equipment, engines, and the chemical industry. Characterized by high compressibility - up to 1:6, strong construction resistant to vibrations and stretching, and impact resistance due to the external spiral. Also available with a stainless steel spiral (from a diameter of 80 mm). Hose installation on couplings with bridge clamps (left-handed). Chemical resistance verification - chemical resistance table for CSM (preliminary selection), confirmation of resistance and application conditions - by Tubes International. Standard length: from 2 to 10 m. Hose material: externally black polyester fabric coated with CSM - Hypalon. Reinforcement: external spiral made of galvanized steel wire and sheet. Operating temperature: from -35°C to +175°C (temporarily up to +190°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly durable, universal high-quality flat hose used in the mining, oil, energy, and agriculture industries. Particularly used for water, sludge, wastewater, and fertilizers. Made from hydrolysis and microbe-resistant polyurethane - polyether. Reinforced with circumferentially woven polyester braid bonded and surrounded by polyurethane in the original hot thermoplastic polyurethane extrusion production process through braiding. The hose has high tensile strength, with minimal elongation under pressure (up to 2%) and no tendency to kink or twist. Due to its durability combined with ease of handling (unrolling, laying, storing), it is widely used in water systems (drainage of open-pit mines, water supply, drainage, and wastewater discharge) and beyond. Resistant to a wide range of chemicals, microbes, fungi, hydrolysis, weather conditions, UV, and ozone. Good abrasion resistance. Available on special order in lengths longer than 200 meters in diameters up to 6”. To confirm the resistance and application conditions of the hose, contact Tubes International. Maximum working pressure for temporary use established according to a safety factor of 2:1 approved by the manufacturer (only for water and safe, non-flammable liquids). For maximum longevity, it is not recommended to exceed 1/3 of the bursting pressure. Standard roll length: 200 m. Hose material: black polyurethane - polyether (PU). Working pressure: from 8 bar to 27 bar - depending on hose diameter and temperature. Operating temperature: from -50°C to +75°C (water).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible suction and discharge hose designed for the transfer of water, beer, wine, alcohols with a concentration of up to 20%, and other food products. Not recommended for milk and its derivatives, oils, and fatty food substances. Compliant with European regulations 1935/2004/EC and 10/2011/EU (simulant fluids A, B, and C). An antistatic wire is placed along the outer layer of the hose. The working pressure is 25% of the bursting pressure. Hose material: transparent PVC. Reinforcement: gray PVC spiral. Working pressure: from 2.4 bar to 5.6 bar, depending on the hose diameter. Operating temperature: from 0°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPUSH-ON end fitting with internal metric thread, type YMW111, designed for self-clamping hose intended for this type of fitting. Mounted to the hose without the use of clamps or bands. Features a special profile of grooves tailored to the material and dimensions of the PUSH-ON hose and the structure of its braid, causing the hose to clamp onto the grooves of the fitting. The fitting should not be used with other hoses or clamped with bands or clamps, as this may damage the hose. Operating temperature: from -40°C to +80°C. Working pressure in accordance with the specifications of the PUSH-ON hose. Material: galvanized carbon steel, brass, AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction and discharge hose designed for the transport of dry abrasive substances. The inner layer is smooth, antistatic, and highly resistant to abrasion (50±5 mm³ according to ISO 4649, formerly DIN 53516). Built-in copper wire that, when grounded (or connected to a grounded end), dissipates electric charges. The outer layer is resistant to weather conditions and ozone. The hose is intended for the transport of dry, highly abrasive substances: cement, sand, gravel, etc. Inner layer: black NR/SBR rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black EPDM rubber. Working pressure: 6 bar. Vacuum: from 0.8 bar to 0.9 bar - depending on the hose diameter. Operating temperature: -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure, highly durable hose for compressed air transmission. Designed for use in harsh conditions such as construction sites, mines, etc., to power equipment with high compressed air consumption. Extremely robust and durable due to high-quality materials and a double-layer construction – double reinforcement with circumferentially woven high-strength polyester braid, completely covered and lined with thermoplastic polyurethane (PU). The hose has very good abrasion resistance, is puncture-resistant, tear-resistant, and oil-resistant. The hose does not elongate under pressure and is resistant to longitudinal loads. Flat in a resting state, which facilitates handling and storage. Available as ready-made hoses of 20 or 40 m in length, with factory-installed fittings. Use for high-pressure air should always be preceded by a risk analysis in case of accidental disconnection or rupture of the hose and potential application of safeguards. The maximum working pressure of the hose is established according to a safety factor of 4:1 approved by the manufacturer for air. Exceeding 1/3 of the specified breaking force is not recommended. Hose material: polyurethane (PU). Reinforcement: double polyester braid. Outer layer: orange polyurethane (PU). Working pressure: from 30 bar to 43.75 bar - depending on the hose diameter. Operating temperature: from -50°C to +110°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible, and smooth interior hose with a white spiral, designed for the removal of dust, chips, fibers, and lightweight bulk materials in the paper, textile, and wood industries. It retains its flexibility and bendability even at low temperatures. The dense steel spiral coated with white PVC ensures high pressure parameters, is resistant to corrosion, and has good adhesion to the hose material. The hose has good resistance to abrasion, oils, and gasoline. Installation on couplings - with bridge clamps (right-handed). Other diameters available upon request. Versions: P1 N PU – standard with high abrasion resistance; P1 N PU AS – antistatic (R ≤ 108 Ω), compliant with TRBS 2153 and for extraction also with TRGS 727, resistant to microbes and hydrolysis; P1 N PU EL – electrically conductive (R ≤ 104 Ω), compliant with ATEX 2014/34/EU, TRBS 2153 and for extraction also with TRGS 727, can be used in explosion hazard zones (after conducting a risk assessment). Hose material: transparent polyester-polyurethane (P1 N PU), transparent polyether-polyurethane (P1 N PU AS), black polyether-polyurethane (P1 N PU EL). Reinforcement: steel wire spiral coated with PVC. Wall thickness measured between the spiral: 0.5 mm and 0.6 mm from diameters of 100 mm. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, specialized drag hose for farmers designed for natural fertilization in crop production (manure and slurry fertilization). Used in comprehensive slurry spreading systems, including spreaders. In these solutions, the slurry is pumped using a hose from the tank to dispensers/tanks mounted on the tractor and then spread directly onto the soil surface. Extremely durable and long-lasting due to high-quality materials and construction. Reinforced with a circumferentially woven high-strength polyester braid bonded and surrounded by polyurethane in the original hot thermoplastic polyurethane extrusion process through braiding. Due to its high resistance to tensile stress, abrasion, punctures, weather conditions, UV radiation, and small bend radius, it is widely used for field fertilization. Also available in other versions: DRAGMAN EXTRA (with increased breaking strength), DRAGMAN PREMIUM (with increased abrasion resistance), and in longer lengths. Maximum working pressure for temporary use established according to a safety factor of 2:1 approved by the manufacturer (only for water and safe, non-flammable liquids). For maximum longevity, it is not recommended to exceed 1/3 of the bursting pressure and the specified breaking strength. Standard roll length: 200 m. Hose material: orange polyurethane (PU) pressed into high-strength polyester braid during hose extrusion. Working pressure: from 15 bar to 22.5 bar - depending on hose diameter and temperature. Operating temperature: from -50°C to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight and flexible hose made of thermoplastic polyurethane intended for low-pressure hydraulic, pneumatic, and water installations. Used in industrial automation and the automotive industry. Free from LABS (linear alkylbenzene sulfonates), thus it does not react with paints. Safety factor of 4:1. It has some resistance to vacuum. The hose is designed to work with self-clamping PUSH-ON type fittings. NON CONDUCTIVE version (TO-107…) is electrically non-conductive (leakage under test conditions according to standards less than 50 μA for a voltage of 246 kV/m for 5 minutes), used with electrical devices, e.g., in cooling systems. Inner layer: polyurethane. Reinforcement: synthetic braid. Outer layer: black polyurethane (standard), orange polyurethane (NON CONDUCTIVE). Working pressure: 20 bar. Operating temperature: from -40°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong, thick suction-discharge hose designed for the transport of a wide range of wet and dry abrasive substances. The thick inner layer is smooth, antistatic, and abrasion-resistant (70 mm³ according to ISO 4649, formerly DIN 53516). Built-in copper wire that, when grounded (or connected to a grounded end), dissipates electric charges. The outer layer is corrugated, weather-resistant, and ozone-resistant. The hose is intended for the transport of abrasive substances mixed with water as well as dry materials: cement, sand, gravel, seeds, etc. Suitable for heavy-duty applications. It can be bent to a relatively small bending radius, but its deflection requires considerable force. It can also be easily cut into sections directly at the place of use and fitted with special PN10 flange fittings (applied to the outer surface of the hose). Used in many applications, e.g., for the transshipment of bulk materials in ports, for the transport of excavated material in mining, in the chemical industry, in construction during demolition work, for suction and transport of water and sludge in dewatering operations, in gravel and sand pits, in dredging and reclamation work. Installation: the hose is designed for installation using the VOLGA FRA system – aluminum half-flanges PN10 applied externally to the hose. Inner layer: black NR/SBR rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black EPDM rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: from -40°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPUSH-ON end fitting with internal metric thread, type YMW111, designed for self-clamping hose intended for this type of fitting. Mounted to the hose without the use of clamps or bands. Features a special profile of grooves tailored to the material and dimensions of the PUSH-ON hose and the structure of its braid, causing the hose to clamp onto the grooves of the fitting. The fitting should not be used with other hoses or clamped using bands or clamps, as this may damage the hose. Operating temperature: from -40°C to +80°C. Working pressure in accordance with the specifications of the PUSH-ON hose. Material: galvanized carbon steel, AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction hose designed for pneumatic transport of dry abrasive substances. Inner layer made of white, smooth, abrasion-resistant rubber (≤110±5 mm³ according to ISO 4649, formerly DIN 53516), food-grade, phthalate-free, compliant with FDA 21 CFR 177.2600 for contact with dry food and BfR XXI category 4. Reinforcement with synthetic cord. Two built-in copper wires that, when grounded (or connected to a grounded end), dissipate electric charges. Outer layer made of electrically conductive rubber, resistant to weather conditions and ozone. Hose intended for the transport of dry food substances: grains, sugar, powders, feeds, granules, etc., as well as other abrasive substances such as PVC granulate, for which a white, non-staining inner layer is required. Not intended for use in ATEX explosion hazard zones. Available in two versions: BN standard (working pressure 6 bar) and BN SPECIAL (working pressure 8 bar). Standard length: 60 m (or 120 m - contact Tubes International). Standards and requirements: Food industry, contact with food 1935/2004/EC, 2023/2006/EC (GMP). Inner layer: white NR/SBR rubber. Reinforcement: synthetic cord. Outer layer: black EPDM rubber. Working pressure: 6 bar or 8 bar. Operating temperature: -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong pressure hose designed for the transmission of water or compressed air. Used in construction (particularly in demolition companies), industry, and mining. Suitable for heavy-duty applications. The yellow color ensures excellent visibility of the hose. The inner layer is smooth, providing minimal flow loss. The outer layer is slightly longitudinally ribbed, which increases abrasion resistance and protects against contact with hot elements. Resistant to abrasion, ozone, weather conditions, oil, fuels, and a wide range of chemicals. Lighter and more flexible than standard rubber hoses. Flat when at rest, facilitating handling and storage. Does not require washing and drying. Resistant to longitudinal loads – during unwinding and pulling (the longitudinal force should never exceed 1/3 of the specified breaking force, and the installation of fittings should consider the longitudinal force). Use for air should always be preceded by a risk analysis in case of accidental disconnection or rupture of the hose. Hose material: yellow NBR/PVC blend embedded in a polyester-polyamide braid during the hose extrusion process. Working pressure: 30 bar (water), 22 bar (air). Operating temperature: from -20°C to +80°C (water), from -20°C to +75°C (air).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, gray in color, very flexible and pliable, chemically resistant and flame-retardant hose intended for use in air conditioning, ventilation, and heating systems. It features high compressibility - up to 1:6, a strong construction resistant to vibrations and stretching, and impact resistance due to the external spiral. Also available in other colors and with a stainless steel spiral (from a diameter of 80 mm). AS version – antistatic (R ≤109 Ω) - made in black. Hose installation on couplings with bridge clamps (left-handed). Chemical resistance check: PVC chemical resistance table (preliminary selection), confirmation of resistance and application conditions by Tubes International. Standard length: from 2 to 10 m - contact Tubes International. Hose material: gray polyester fabric impregnated with PVC. Reinforcement: external spiral made of galvanized steel wire and sheet. Operating temperature: from -20°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPUSH-ON JIC end fitting with internal UNF thread, type YJW110, designed for self-clamping hose intended for this type of fitting. Mounted to the hose without the use of clamps or bands. Features a special profile of grooves adapted to the material and dimensions of the PUSH-ON hose and the structure of its braid, causing the hose to clamp onto the grooves of the fitting. The fitting should not be used with other hoses or clamped with bands or clamps, as this may damage the hose. Operating temperature: from -40°C to +80°C. Working pressure in accordance with the specifications of the PUSH-ON hose. Material: galvanized carbon steel, brass, AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction and pressure hose designed for the transfer of dry or liquid abrasive substances, granules, etc. Externally corrugated, internally smooth. The inner layer is made of transparent, abrasion-resistant polyurethane, with a thickness ranging from 0.6 mm (DN30) to 1 mm (DN100). The hose features a copper wire arranged in a spiral along its length, which discharges electric charges when grounded or connected to an end fitting. Widely used in plastic processing in applications requiring higher resistance to abrasion, puncturing, and cutting of the hose. Particularly recommended for plastic regenerates with relatively sharp edges. Standards and requirements: food industry, contact with food: compliant with European regulations 1935/2004/EC and 10/2011/EU (simulant fluids A, B, and C), 2023/2006/EC (GMP) – applihose to liquid food substances. Inner layer: transparent polyurethane. Outer layer: transparent PVC. Reinforcement: hard PVC spiral. Working pressure: from 3 bar to 5 bar, depending on the hose diameter and temperature. Vacuum: up to 0.7 bar. Operating temperature: -10°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible rubber fire hose, designed for use on reels. The ANKARA EN hose is manufactured according to the EN 694 standard, which is the European standard for hoses used in fixed fire protection installations and commonly used on reels in fixed hydrants in buildings, industrial installations, shopping centers, etc. The inner layer is made of EPDM rubber, resistant to light chemicals and fire-fighting foaming agents. The outer layer is made of EPDM rubber, resistant to abrasion and weather conditions. It performs excellently when mounted on reels, ensuring water flow even when the hose is not fully extended. The presented ANKARA hose is made according to the requirements of the older DIN 14817: 1991 standard, intended for powder and foam extinguishing agents, with an inner layer made of conductive NR/SBR rubber and a working pressure of up to 20 bar, also designed for use on reels. Inner layer: EPDM rubber (ANKARA EN), conductive NR/SBR rubber (ANKARA). Reinforcement: synthetic cord. Outer layer: EPDM rubber (ANKARA EN), SBR rubber (ANKARA). Working pressure: from 7 bar to 20 bar - depending on the size and type of hose. Operating temperature: from -20°C to +60°C (ANKARA EN), from -40°C to +70°C (ANKARA).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible, and elastic hose designed for the extraction of hot vapors, smoke, gases, dust, cooling air discharge, and blowing. Flame-retardant, resistant to temperature, UV radiation, ozone, and aging. Used in all areas of industry for high-temperature applications, including extraction from furnaces in the metallurgical industry, foundries, glass, and ceramic industries. Characterized by high compressibility, strong construction resistant to vibrations and stretching, and impact resistance due to the external spiral. Other diameters available upon special request in the range of 50 to 508 mm. Hose installation on couplings with bridge clamps (left-handed). Standard length: 3 m (also available in lengths of 6 and 10 m upon special request). Hose material: glass fabric impregnated with silicone (silver-gray), with a thickness of 0.4 mm. Reinforcement: external spiral made of galvanized steel wire and sheet. Operating temperature: from -60°C to +300°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPUSH-ON end with internal BSP thread (60° cone sealing), type YBW110, designed for self-clamping hose intended for this type of end. Mounted to the hose without the use of clamps or bands. Features a special profile of grooves adapted to the material and dimensions of the PUSH-ON hose and the structure of its braid, causing the hose to clamp onto the grooves of the end. The end should not be used with other hoses or clamped using bands or clamps, as this may damage the hose. Operating temperature: from -40°C to +80°C. Working pressure in accordance with the specifications of the PUSH-ON hose. Material: galvanized carbon steel, brass, AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRectangular corrugated hose reinforced with a steel spiral, for hot water and antifreeze fluids, intended for automotive and industrial cooling systems. It has vacuum resistance. Inner layer resistant to heat and cooling fluids. Outer layer resistant to overheating, oil, and aging. Inner layer: black CR rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black CR rubber. Working pressure: up to 4 bar. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThree-layer suction hose with a specific construction designed for the discharge of very hot (up to 1100°C) gases, vapors, smoke, and air. The outer layer of impregnated glass fabric with stainless steel threads provides mechanical strength, the middle thick high-temperature fabric serves as insulation, and the inner very fine stainless steel mesh separates the flow of hot gases. Flame retardant, resistant to hot sparks to some extent. Used with furnaces and engines for the extraction of very high-temperature gases in the metallurgical, ceramic, shipbuilding, aerospace, automotive, and military equipment industries. The hose has a strong construction and is resistant to damage due to the external spiral. Used exclusively as a suction hose operating under vacuum, due to the possibility of gas permeation outside under pressure (degassing). Hoses with a small internal diameter < 100 mm feature a so-called double-hose construction (the inner mesh layer constitutes a separate hose with a spiral). Hose installation on couplings with left-handed bridge clamps. Standard length: from 2 to 10 m - depending on the diameter. Hose material: 3 layers: externally impregnated glass fabric with stainless steel fibers (gray), middle layer - high-temperature insulating fabric, inside fine mesh - stainless steel. Reinforcement: external spiral made of wire and sheet metal from stainless steel. Operating temperature: from -50°C to +1100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPressure hose for sandblasting, extremely resistant to abrasion. Thick inner layer made of rubber with exceptionally good abrasion resistance (40±5 mm³ according to ISO 4649 / DIN 53516). Exceeds the requirements of ISO 3861:2008 standard. The inner and outer layers are antistatic, preventing the accumulation of electric charges. Used for highly abrasive materials such as quartz sand, steel shot, corundum, glass in abrasive blasting of steel structures, castings, concrete surfaces, etc. Fitted with special nozzles for sandblasting. Standard length: 60 m / 40 m for a diameter of 16 mm (or 120 m - contact Tubes International). Inner layer: black NR/SBR rubber. Reinforcement: synthetic cord. Outer layer: black synthetic rubber. Working pressure: 12 bar. Operating temperature: from -40°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° PUSH-ON fitting with internal BSP thread, type YBW210, designed for a special self-clamping hose intended for this type of fitting. Mounted to the hose without the use of clamps or bands. Features a special profile of grooves adapted to the material and dimensions of the PUSH-ON hose and the structure of its braid, causing the hose to clamp onto the grooves of the fitting. The fitting should not be used with other hoses or clamped with bands or clamps, as this may damage the hose. Operating temperature: from -40°C to +80°C. Working pressure in accordance with the specifications of the PUSH-ON hose. Material: galvanized carbon steel, AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPressure hose for sandblasting, extremely resistant to abrasion. Thick inner layer made of rubber with exceptionally good abrasion resistance (36 mm³ according to ISO 4649:2014). Exceeds the requirements of ISO 3861:2008 standard. The inner layer is electrically conductive and the outer layer is antistatic, preventing the accumulation of electric charges. Used for highly abrasive materials such as quartz sand, steel shot, corundum, glass in abrasive jet processing of steel structures, castings, concrete surfaces, etc. Fitted with special nozzles for sandblasting. Inner layer: black NR/BR/SBR rubber. Reinforcement: synthetic cord. Outer layer: black SBR rubber. Working pressure: 12 bar. Operating temperature: from -35°C to +80°C.
