Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible suction and discharge hose designed for the transfer of water, beer, wine, alcohols with a concentration of up to 20%, and other food products. Not recommended for milk and its derivatives, oils, and fatty food substances. Compliant with European regulations 1935/2004/EC and 10/2011/EU (simulant fluids A, B, and C). An antistatic wire is placed along the outer layer of the hose. The working pressure is 25% of the bursting pressure. Hose material: transparent PVC. Reinforcement: gray PVC spiral. Working pressure: from 2.4 bar to 5.6 bar, depending on the hose diameter. Operating temperature: from 0°C to +60°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure, highly durable hose for compressed air transmission. Designed for use in harsh conditions such as construction sites, mines, etc., to power equipment with high compressed air consumption. Extremely robust and durable due to high-quality materials and a double-layer construction – double reinforcement with circumferentially woven high-strength polyester braid, completely covered and lined with thermoplastic polyurethane (PU). The hose has very good abrasion resistance, is puncture-resistant, tear-resistant, and oil-resistant. The hose does not elongate under pressure and is resistant to longitudinal loads. Flat in a resting state, which facilitates handling and storage. Available as ready-made hoses of 20 or 40 m in length, with factory-installed fittings. Use for high-pressure air should always be preceded by a risk analysis in case of accidental disconnection or rupture of the hose and potential application of safeguards. The maximum working pressure of the hose is established according to a safety factor of 4:1 approved by the manufacturer for air. Exceeding 1/3 of the specified breaking force is not recommended. Hose material: polyurethane (PU). Reinforcement: double polyester braid. Outer layer: orange polyurethane (PU). Working pressure: from 30 bar to 43.75 bar - depending on the hose diameter. Operating temperature: from -50°C to +110°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, specialized drag hose for farmers designed for natural fertilization in crop production (manure and slurry fertilization). Used in comprehensive slurry spreading systems, including spreaders. In these solutions, the slurry is pumped using a hose from the tank to dispensers/tanks mounted on the tractor and then spread directly onto the soil surface. Extremely durable and long-lasting due to high-quality materials and construction. Reinforced with a circumferentially woven high-strength polyester braid bonded and surrounded by polyurethane in the original hot thermoplastic polyurethane extrusion process through braiding. Due to its high resistance to tensile stress, abrasion, punctures, weather conditions, UV radiation, and small bend radius, it is widely used for field fertilization. Also available in other versions: DRAGMAN EXTRA (with increased breaking strength), DRAGMAN PREMIUM (with increased abrasion resistance), and in longer lengths. Maximum working pressure for temporary use established according to a safety factor of 2:1 approved by the manufacturer (only for water and safe, non-flammable liquids). For maximum longevity, it is not recommended to exceed 1/3 of the bursting pressure and the specified breaking strength. Standard roll length: 200 m. Hose material: orange polyurethane (PU) pressed into high-strength polyester braid during hose extrusion. Working pressure: from 15 bar to 22.5 bar - depending on hose diameter and temperature. Operating temperature: from -50°C to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight and flexible hose made of thermoplastic polyurethane intended for low-pressure hydraulic, pneumatic, and water installations. Used in industrial automation and the automotive industry. Free from LABS (linear alkylbenzene sulfonates), thus it does not react with paints. Safety factor of 4:1. It has some resistance to vacuum. The hose is designed to work with self-clamping PUSH-ON type fittings. NON CONDUCTIVE version (TO-107…) is electrically non-conductive (leakage under test conditions according to standards less than 50 μA for a voltage of 246 kV/m for 5 minutes), used with electrical devices, e.g., in cooling systems. Inner layer: polyurethane. Reinforcement: synthetic braid. Outer layer: black polyurethane (standard), orange polyurethane (NON CONDUCTIVE). Working pressure: 20 bar. Operating temperature: from -40°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction hose designed for pneumatic transport of dry abrasive substances. Inner layer made of white, smooth, abrasion-resistant rubber (≤110±5 mm³ according to ISO 4649, formerly DIN 53516), food-grade, phthalate-free, compliant with FDA 21 CFR 177.2600 for contact with dry food and BfR XXI category 4. Reinforcement with synthetic cord. Two built-in copper wires that, when grounded (or connected to a grounded end), dissipate electric charges. Outer layer made of electrically conductive rubber, resistant to weather conditions and ozone. Hose intended for the transport of dry food substances: grains, sugar, powders, feeds, granules, etc., as well as other abrasive substances such as PVC granulate, for which a white, non-staining inner layer is required. Not intended for use in ATEX explosion hazard zones. Available in two versions: BN standard (working pressure 6 bar) and BN SPECIAL (working pressure 8 bar). Standard length: 60 m (or 120 m - contact Tubes International). Standards and requirements: Food industry, contact with food 1935/2004/EC, 2023/2006/EC (GMP). Inner layer: white NR/SBR rubber. Reinforcement: synthetic cord. Outer layer: black EPDM rubber. Working pressure: 6 bar or 8 bar. Operating temperature: -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong pressure hose designed for the transmission of water or compressed air. Used in construction (particularly in demolition companies), industry, and mining. Suitable for heavy-duty applications. The yellow color ensures excellent visibility of the hose. The inner layer is smooth, providing minimal flow loss. The outer layer is slightly longitudinally ribbed, which increases abrasion resistance and protects against contact with hot elements. Resistant to abrasion, ozone, weather conditions, oil, fuels, and a wide range of chemicals. Lighter and more flexible than standard rubber hoses. Flat when at rest, facilitating handling and storage. Does not require washing and drying. Resistant to longitudinal loads – during unwinding and pulling (the longitudinal force should never exceed 1/3 of the specified breaking force, and the installation of fittings should consider the longitudinal force). Use for air should always be preceded by a risk analysis in case of accidental disconnection or rupture of the hose. Hose material: yellow NBR/PVC blend embedded in a polyester-polyamide braid during the hose extrusion process. Working pressure: 30 bar (water), 22 bar (air). Operating temperature: from -20°C to +80°C (water), from -20°C to +75°C (air).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible rubber fire hose, designed for use on reels. The ANKARA EN hose is manufactured according to the EN 694 standard, which is the European standard for hoses used in fixed fire protection installations and commonly used on reels in fixed hydrants in buildings, industrial installations, shopping centers, etc. The inner layer is made of EPDM rubber, resistant to light chemicals and fire-fighting foaming agents. The outer layer is made of EPDM rubber, resistant to abrasion and weather conditions. It performs excellently when mounted on reels, ensuring water flow even when the hose is not fully extended. The presented ANKARA hose is made according to the requirements of the older DIN 14817: 1991 standard, intended for powder and foam extinguishing agents, with an inner layer made of conductive NR/SBR rubber and a working pressure of up to 20 bar, also designed for use on reels. Inner layer: EPDM rubber (ANKARA EN), conductive NR/SBR rubber (ANKARA). Reinforcement: synthetic cord. Outer layer: EPDM rubber (ANKARA EN), SBR rubber (ANKARA). Working pressure: from 7 bar to 20 bar - depending on the size and type of hose. Operating temperature: from -20°C to +60°C (ANKARA EN), from -40°C to +70°C (ANKARA).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPressure hose for sandblasting, extremely resistant to abrasion. Thick inner layer made of rubber with exceptionally good abrasion resistance (40±5 mm³ according to ISO 4649 / DIN 53516). Exceeds the requirements of ISO 3861:2008 standard. The inner and outer layers are antistatic, preventing the accumulation of electric charges. Used for highly abrasive materials such as quartz sand, steel shot, corundum, glass in abrasive blasting of steel structures, castings, concrete surfaces, etc. Fitted with special nozzles for sandblasting. Standard length: 60 m / 40 m for a diameter of 16 mm (or 120 m - contact Tubes International). Inner layer: black NR/SBR rubber. Reinforcement: synthetic cord. Outer layer: black synthetic rubber. Working pressure: 12 bar. Operating temperature: from -40°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPressure hose for sandblasting, extremely resistant to abrasion. Thick inner layer made of rubber with exceptionally good abrasion resistance (36 mm³ according to ISO 4649:2014). Exceeds the requirements of ISO 3861:2008 standard. The inner layer is electrically conductive and the outer layer is antistatic, preventing the accumulation of electric charges. Used for highly abrasive materials such as quartz sand, steel shot, corundum, glass in abrasive jet processing of steel structures, castings, concrete surfaces, etc. Fitted with special nozzles for sandblasting. Inner layer: black NR/BR/SBR rubber. Reinforcement: synthetic cord. Outer layer: black SBR rubber. Working pressure: 12 bar. Operating temperature: from -35°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible water hose designed for winding on reels. Intended for use in high-pressure firefighting equipment and fire trucks (booster hose). The inner layer is resistant to extinguishing agents and foaming agents. Reinforcement made of a thick layer of high-strength cord. The outer layer is weather-resistant. The CHICAGO EN hose differs from the basic version of the CHICAGO hose by being manufactured in accordance with standard EN 1947: 2014 (type C, class 1, category 2), while the CHICAGO EN GL is manufactured in accordance with EN 1947 but features a luminescent outer layer, allowing for easy visibility in darkness or smoke. Special versions of the hose compliant with standards ASTM C-542 and BS 3169 are also available upon request. Standard roll length: 60 m (120 m upon confirmation for the basic version of the hose). Inner layer: black EPDM rubber. Reinforcement: synthetic cord. Outer layer: black EPDM rubber (yellow luminescent synthetic rubber – GL version). Working pressure: 40 bar. Operating temperature: from -40°C to +100°C, from -20°C to +60°C (EN 1947).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose in the system 3/4" made of corrosion-resistant acetal, resistant to solvents, oils, and greases, providing rigidity and elasticity of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and does not cause damage to cutting tools. Very easy to expand modular construction. Available lengths: 2x145 mm, 100 mm, 200 mm, 300 mm, 400 mm, 500 mm, 600 mm, 700 mm, 800 mm, 900 mm, and 1000 mm. Material: acetal. Working pressure: up to 1.4 bar. Maximum flow: 5182 l/hour. Operating temperature: up to +76°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsExtremely lightweight, flexible water delivery hose designed for internal fire protection of buildings. The inner layer is made of high-quality synthetic rubber. The outer layer consists of a strong, dense polyester braid reinforced with a thin, tightly wound PET spiral. The hose is used in internal hydrant cabinets with a length of 20 m to 30 m of hose wound on a drum (reel) with a nozzle mounted at the end of the hose. Compliant with EN 694 standard for fire hoses (type B class 5). In the field of fire protection (Poland), it has a CNBOP-PIB compliance certificate. It can also be used in industry - for seawater, industrial water, and some light diluted chemicals, as well as for air, dust, and light solid particles. It is not intended for use in harsh external conditions. Installation with clamps or crimping sleeves on ends with smooth, sharp-free fittings to avoid cutting the inner layer. Inner layer: smooth synthetic rubber. Reinforcement: polyester braid with a reinforcing spiral (thread) PET. Working pressure: from 7 bar to 12 bar - depending on the hose diameter. Operating temperature: from -20°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSoft suction hose, for larger diameters and small thicknesses almost flat at rest, intended for pneumatic transport of dry bulk materials. Inner layer made of black, smooth, antistatic rubber (R < 106 Ω), abrasion-resistant (70±5 mm3 according to ISO 4649, formerly DIN 53516). Reinforcement with synthetic cord. Outer layer made of antistatic (R < 106 Ω) abrasion-resistant rubber, weather-resistant and ozone-resistant. The hose is primarily used for the transfer of cement, sand, gravel, silica, and other dry abrasive materials from rail tankers, road tankers, and silos. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black NR/SBR rubber. Reinforcement: synthetic cord. Outer layer: black NR/SBR rubber. Working pressure: from 5 bar to 6 bar - depending on the hose diameter. Operating temperature: from -40°C to +70°C. Indices marked at the end with the letters XE have an inner layer made of high-abrasion-resistant antistatic rubber (abrasion 50 mm3 according to ISO4649) and with a copper wire.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThick, strong, flexible, crush-resistant pressure hose designed for the transmission of hot, dry air from the compressor to the tank installation of the tanker. Used in road tankers for the transport of bulk materials: cement trucks, feed trucks, etc., as well as in other industrial installations. The outer layer is resistant to ozone and weather conditions. Standard length: 60 m or 120 m. Inner layer: white EPR rubber. Reinforcement: synthetic cord. Outer layer: blue EPDM rubber. Working pressure: 10 bar. Operating temperature: from -40°C to +200°C (temporarily up to +240°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible compressed air hose with good resistance to mineral oils. Very abrasion-resistant. The yellow color ensures excellent visibility of the hose. The hose has a thickened outer layer every 20 m, marked on the hose ("TAGLIO / CUT"), and it is recommended to cut the hose and install fittings at these points. This reinforces the fitting installation area and makes it more resistant to bending. From a 60 m roll, three 20 m hoses with fittings can be made. However, it is also possible to use the hose with fittings installed in non-thickened areas. The hose is used for pneumatic hammers and drills. Inner layer: black PVC/NBR blend. Reinforcement: double polyester braid. Outer layer: black or yellow PVC/PU blend. Working pressure: 20 bar - dependent on temperature. Operating temperature: from -10°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPressure hose for plastering. Inner layer made of rubber with good abrasion resistance (70±5 mm³ according to ISO 4649 / DIN 53516). Both inner and outer layers are antistatic to prevent the accumulation of electric charges. Multiple reinforcement with synthetic cord ensures high pressure resistance. Outer layer resistant to abrasion, weather conditions, and ozone. Used for spraying wet mortar: cement, plaster, and gypsum in construction work. Commonly used with plastering machines. Fitted with special ends for plastering. The NIAGARA LIGHT hose is an economical version with a slightly thinner wall (marked with the letter "L" at the end of the index). Standard length: 60 m and 40 m LIGHT version (or 120 m - contact Tubes International). Inner layer: black SBR/NR rubber. Reinforcement: synthetic cord. Outer layer: black SBR/NR rubber. Working pressure: 40 bar. Operating temperature: from -40°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPressure hose for pneumatic transport of dry abrasive substances. Special hose design with exceptional abrasion resistance. The inner layer is smooth, made of black antistatic natural rubber with embedded alumina (Al2O3) ceramic beads, a material with high hardness. Built-in copper wire that, when grounded (connected to a grounded end), dissipates electric charges. The outer layer is made of black antistatic (R<106Ω) SBR/NR rubber resistant to abrasion and aging. The hose is intended for the transport of dry highly abrasive substances: e.g., dry cement, coal, coal dust, coke, solid fuels from secondary raw materials, minerals, ceramic powders, steel shot, glass shards, fiberglass. Used in steel mills, coking plants, power plants, cement plants, mines, glassworks, abrasive material factories, and insulation material factories. The advantage is the long lifespan of the hose in these applications – a traditional abrasion-resistant rubber hose may last only a few days, while the ALUSPHERE hose can last several months under the same conditions. Inner layer: ceramic beads embedded in black NR rubber. Reinforcement: synthetic cord. Outer layer: black SBR/NR rubber. Working pressure: 12 bar. Operating temperature: from -30°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose for sandblasting. Thick inner layer made of rubber with very good abrasion resistance (50±5 mm³ according to ISO 4649 / DIN 53516). The inner and outer layers are antistatic, preventing the accumulation of electric charges. Used for sand and steel shot in abrasive blasting of steel structures, castings, concrete surfaces, etc. Commonly used in the metal and shipbuilding industries. Fitted with special nozzles for sandblasting. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black NR/SBR rubber. Reinforcement: synthetic cord. Outer layer: black NR/SBR rubber. Working pressure: 12 bar. Operating temperature: from -40°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, smooth, flat-wound hose designed for the discharge of bulk materials. Particularly used in installations exposed to vibrations and mechanical damage. Suitable for contact with food and in the pharmaceutical industry, being tasteless and odorless, in compliance with FDA requirements (21CFR177.2600). It is not subject to hydrolysis and is resistant to microbes. Also resistant to mineral oils, aging, atmospheric factors, ozone, UV, and many chemicals. Hose material: transparent polyurethane. Working pressure: from 0.135 bar to 1.03 bar, depending on the hose diameter. Operating temperature: -40°C to +90°C (temporarily +125°).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible suction hose designed for the transport of petrochemical products with aromatic compound content up to 50%, fuels, for oil systems, lubrication, etc. Outer layer resistant to fuels, oils, and weather conditions. Inner layer: black NBR rubber. Reinforcement: synthetic braid. Outer layer: black NBR/PVC rubber. Working pressure: 10 or 20 bar. Operating temperature: from -20°C to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong pressure hose designed for hot oil in hydraulic systems under pressure up to 40 bar. The outer layer is made of blue synthetic rubber, self-extinguishing (in accordance with MSHA requirements), resistant to weather conditions. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black synthetic rubber. Reinforcement: synthetic braid. Outer layer: blue self-extinguishing synthetic rubber. Working pressure: 40 bar. Operating temperature: from -30°C to +130°C (temporarily up to +150°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight and flexible suction hose designed for the transfer of liquid products in the petrochemical industry, containing up to 30% aromatic compounds. It features a copper wire ensuring electrical continuity between the hose ends. The outer layer is resistant to abrasion, oil, and weather conditions. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black NBR rubber. Reinforcement: synthetic cord. Outer layer: black synthetic rubber. Working pressure: 10 bar. Operating temperature: from -20°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible pressure hose for industrial oils, mineral oils, unleaded gasoline (EN 228:2017), diesel fuel (EN 590:2010), heating oil (DIN 51 603 1÷5). Also suitable for compressed air. Inner layer made of black, smooth NBR rubber, antistatic R<106 Ω/m (EN ISO 8031:2009). Reinforcement with textile braid provides a safety factor of 3.15:1. Resistant to slight vacuum up to approximately 0.5 bar. Outer layer made of black, smooth NBR/EPDM rubber compound resistant to oil, ozone, abrasion, and weather conditions. Inner layer: black NBR rubber. Reinforcement: textile braid. Outer layer: black NBR/EPDM rubber. Working pressure: 25 bar. Operating temperature: from -40°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, soft rubber hose with an external braid made of galvanized steel, intended for gasoline and petroleum-based oils such as diesel, heating oil, and lubricating oil. Installed in fuel and oil systems of small vehicles and industrial equipment. Can also be used for water, cooling fluids, non-oxidizing detergents, and air. Based on the requirements of standard DIN 73379. Inner layer made of smooth black NBR rubber. The external reinforcing braid made of galvanized steel provides high pressure resistance. The braid features a black marking stripe. Maximum operating temperature depends on the medium: for gasoline, unleaded gasoline, fuels with up to 50% aromatic hydrocarbon content: +40°C; for diesel oil: +80°C; for water and cooling liquids based on ethylene glycol: +90°C; for air: +80°C; for liquid, non-oxidizing detergents: +80°C. Hose material: black NBR rubber. Reinforcement: external wire braid made of galvanized steel. Working pressure: from 10 bar to 20 bar, depending on the hose diameter. Operating temperature: from -35°C to +80°C (maximum temperature depends on the medium).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, soft rubber hose with an external textile braid, primarily intended for fuel installations of leaded and unleaded gasoline as well as diesel oil for small vehicles (cars, motorcycles, mopeds, garden tractors) or industrial equipment. Installed, for example, between the fuel pump and the carburetor. Not suitable for engines with fuel injection systems. Can also be used for water, cooling fluids, non-oxidizing detergents, and air. Based on the requirements of standard DIN 73379 type B (03/1982). The inner layer is made of smooth black NBR rubber. The external textile braid vulcanized with rubber reinforces the hose and protects against contact with hot components. The maximum operating temperature depends on the medium: for gasoline, unleaded gasoline, fuels with up to 50% aromatic hydrocarbon content: +40°C; for diesel oil: +80°C; for water and cooling liquids based on ethylene glycol: +90°C; for air: +80°C; for liquid, non-oxidizing detergents: +80°C. Hose material: black NBR rubber. Reinforcement: external black textile braid. Working pressure: 10 bar. Operating temperature: from -35°C to +120°C (temporarily), maximum operating temperature depends on the medium.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery flexible and elastic hose for unleaded gasoline and diesel fuel for passenger cars, trucks, and tractors. Can be used in the engine compartment of trucks. The inner layer is made of black, smooth NBR rubber highly resistant to fuel (oil resistance: RMA class A), suitable for use with most automotive fuels (standard diesel B7 (EN590:2017), biodiesel B20, B100, standard unleaded gasoline E5 (EN228:2017), E10, E85, and E100 - 100% ethanol). Reinforced with a durable textile braid providing a safety factor of 4:1. The outer layer is made of black, smooth, high-quality synthetic rubber resistant to oil, ozone, and weather conditions. Commonly used fuel hose for vehicles. Compliant with SAE J30R2 and SAE J30 R6 standards. Inner layer: NBR rubber. Reinforcement: textile braid. Outer layer: black synthetic rubber. Working pressure: 12 bar. Operating temperature: from -40°C to +100°C externally to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible rubber hose CODAN 3106 designed for leaded and unleaded gasoline. Used for connecting, e.g., the carburetor to the fuel pump in cars, motorcycles, mopeds, garden tractors, etc. Not suitable for engines with fuel injection systems. Based on the requirements of standard DIN 73379 type B (03/1982). Inner layer made of smooth black NBR/PVC rubber compound. Outer braid made of polyester fiber vulcanized with rubber reinforces the hose and protects against contact with hot components. Can also be used for water, cooling fluids, non-oxidizing detergents, air. Maximum operating temperature depends on the medium: for water and cooling liquids based on ethylene glycol: +90°C, for air: +80°C, for liquid non-oxidizing detergents: +80°C, for diesel fuel: +80°C, for gasoline, unleaded gasoline, fuels with up to 50% aromatic hydrocarbons: +40°C. Hose material: black NBR/PVC rubber. Reinforcement: external textile braid (black polyester). Working pressure: from 5 bar to 13 bar, depending on the hose diameter. Operating temperature: from -30°C to +100°C (temporarily), maximum operating temperature depends on the medium.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality, multi-layer fuel hose, based on the requirements of standard DIN 73379-3E (11/97). Construction: inner layer made of chemically and thermally resistant Viton (FPM), intermediate layer made of epichlorohydrin (ECO), temperature-resistant and durable aramid fiber braid, outer layer made of epichlorohydrin (ECO) – resistant to temperature, ozone, micro-cracking. The inner layer of Viton provides excellent chemical resistance to hydrocarbons, petrochemical products, as well as many aggressive chemicals and additives used in fuels, even at elevated operating temperatures. Particularly recommended for biodiesel based on fatty acid methyl esters (FAME) such as biodiesel B10, B20, B100. Resistant to methyl ester of rapeseed oil fatty acids (RME). Can be used for biofuels containing ethanol such as E10, E100. Resistant to phosphate esters (which are also additives to liquid fuels). Can also be used for regular diesel, gasoline, mineral oils. Recommended for demanding applications in terms of high fuel purity, temperature resistance, and aging. Characterized by low permeability of hydrocarbons through the hose wall. Inner layer: FPM rubber (Viton). Intermediate layer: epichlorohydrin rubber (ECO). Reinforcement: aramid textile braid. Outer layer: epichlorohydrin rubber (ECO). Working pressure: 10 bar. Operating temperature: from -40°C to +125°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction and discharge hose designed for the transfer and handling of hot liquid asphalt, tar, and bituminous products. Used for loading and unloading road and rail tankers, in bitumen production plants, and at ports. Inner layer: black polyacrylic blend. Reinforcement: steel wire cord, steel spiral. Outer layer: black synthetic rubber. Working pressure: 10 bar. Operating temperature: from -15°C to +200°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, soft rubber hose with an external braid made of galvanized steel, intended for gasoline and petroleum-based oils such as gear oil, heating oil, and diesel. Installed in fuel and oil systems of small vehicles and industrial equipment. Can also be used for water, cooling fluids, non-oxidizing detergents, and air. Based on the requirements of standard DIN 73379. Inner layer made of smooth, black NBR rubber. The external reinforcing braid made of galvanized steel ensures high pressure resistance. Hose material: black NBR rubber. Reinforcement: external wire braid made of galvanized steel. Working pressure: from 6 bar to 25 bar - depending on the hose diameter. Operating temperature: from -35°C to +90°C (temporarily 110°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose made of a special PVC blend designed for oils, fuels, and other hydrocarbon-based petrochemical products. The hose material has enhanced resistance to leaching of plasticizers and maintains its flexibility even after prolonged use. It withstands repeated bending while exhibiting excellent aging resistance. Intended for fuel installations: pumps, burners, heating devices, oil systems. Not suitable for aromatic hydrocarbons (benzene, toluene, xylene, etc.). Not recommended for gasoline, especially for intensive use or more demanding applications (in such cases, consider the TECHNOBEL PU hose). Can be used for certain chemical products: diluted acids, bases, and alcohols. Smooth inner and outer surface of the hose and semi-transparent wall allow for visual flow control. Widely used in the automotive industry, assembly plants, plastics industry, woodworking industry, automotive workshops, agriculture, forestry, and municipal services. Inner layer: greenish transparent PVC. Reinforcement: synthetic braid. Outer layer: greenish transparent PVC. Working pressure: from 8 bar to 13 bar, depending on the hose diameter. Operating temperature: from -15°C to +60°C (working pressure dependent on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, extremely flexible and pliable PVC hose with a small bending radius, featuring an internal layer of polyurethane (PU, polyester-polyurethane). Due to the good chemical resistance of polyurethane, the hose can be used for gasoline, unleaded gasoline, oils, petroleum products, and many solvents. Suitable for compressed air, including oiled air. Due to the good abrasion resistance of polyurethane, it can also be used for conveying moderately abrasive powders or granules. However, it is not recommended for acids, bases, and aqueous solutions at temperatures above 40ºC. Not suitable for aromatic hydrocarbons (benzene, toluene, xylene, etc.). The hose is widely used in all areas of industry. Also used in agriculture for agricultural spraying (insecticides, pesticides, herbicides, etc.). Used for compressed air for pneumatic tools, spray guns, painting, sandblasting, etc. The outer layer is resistant to hydrocarbons and solvent mists. Suitable for mounting on reels. Inner layer: transparent polyurethane (PU). Reinforcement: polyester braid. Outer layer: black PVC. Working pressure: from 12 bar to 20 bar, depending on the hose diameter and temperature. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose with fittings intended for sanitary installations (hot and cold water). Widely used for connections in industrial systems, central heating, and air conditioning. Resistant to glycol concentrations up to 35%. Fittings made of brass, sleeves made of stainless steel (AISI 304). Has a hygiene certificate and technical approval for use in construction. Available with internal BSP thread on both ends and with internal and external BSP threads. Inner layer: black EPDM rubber (with enhanced parameters). Reinforcement: external braid made of AISI 304 steel. Working pressure: 16 bar. Operating temperature: up to +110°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose in a 1/2" system made of corrosion-resistant acetal, resistant to solvents, oils, and greases, providing rigidity and flexibility of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and does not cause damage to cutting tools. Very easy to expand modular construction. Available lengths: 2x140 mm, 100 mm, 200 mm, 300 mm, 400 mm, 500 mm, 600 mm, 700 mm, 800 mm, 900 mm, and 1000 mm. Material: acetal. Working pressure: up to 2 bar. Maximum flow: 2173 l/hour. Operating temperature: up to +76°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose intended for water and non-corrosive media. Used in sanitary installations, boilers, cooling systems. Two red stripes woven into the braid indicate the hose's resistance to elevated medium temperatures. Inner layer: non-toxic EPDM rubber. Reinforcement: braided galvanized steel. Working pressure: from 6 bar to 15 bar, depending on the hose diameter. Operating temperature: from -10°C to +110°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsReinforced rubber hose with a galvanized steel braid providing high pressure resistance, perfectly suited for oil installations in small vehicles, fuel systems, and industrial equipment. Designed for gasoline and petroleum-based oils such as gear oil, heating oil, or diesel. The inner layer made of NBR rubber combined with a mesh braid makes the hose both soft and flexible. The maximum operating temperature depends on the medium: for gasoline, unleaded gasoline, fuels with up to 50% aromatic hydrocarbons: +40°C; for diesel: +80°C; for water and coolant liquids based on ethylene glycol: +90°C; for air: +80°C; for liquid, non-oxidizing detergents: +80°C. Inner layer: smooth, black NBR rubber. Reinforcement: external wire braid made of galvanized steel. Working pressure: from 20 bar to 25 bar - depending on the hose diameter. Operating temperature: from -35°C to +90°C (maximum operating temperature depends on the medium).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose designed for the transmission of industrial oils, mineral oils, diesel fuel (EN 590:2010), biodiesel, and heating oil (DIN 51 603 1÷5) under higher pressure. Also suitable for compressed air and glycol-based coolants. The inner layer is made of black, smooth NBR rubber, antistatic R<106 Ω/m (EN ISO 8031:2009). Reinforcement with durable textile braid provides a safety factor of 4:1. Resistant to slight vacuum up to approximately 0.6 bar. The outer layer is made of black, smooth SBR/NVC rubber (NVC - a blend of NBR and PVC) and is resistant to oil, ozone, and weather conditions. Inner layer: black NBR rubber. Reinforcement: polyester braid. Outer layer: black SBR/NVC rubber. Working pressure: 40 bar. Operating temperature: from -45°C to +100°C for fuels and oils, from -45°C to +70°C for air.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSoft, flexible, extruded suction hose for the transfer of gasoline and diesel fuel at low pressure, fire-resistant, for small vessels - recreational boats up to 24 m in length. Designed for fuel installations of stationary engines on ships, motorboats, yachts, etc. Suitable for unleaded gasoline, gasoline with up to 10% ethanol (E10 gasoline), diesel fuel, and diesel fuel with 10% FAME esters (B10 - biodiesel). Compliant with ISO 7840 type A1 (fire-resistant, fuel vapor permeability less than or equal to 100 g/m²/24 h), compliant with directive 94/25/EC, certified by RINA, compliant with SAE 1527, USCG type A1. Inner layer made of black, seamless synthetic rubber, resistant to oils and fuels with up to 50% aromatic hydrocarbon content. Reinforcement with synthetic textile braid. Outer layer made of black, fire-resistant, seamless synthetic rubber, resistant to aging, lubricants, weather conditions, and temperature (fire resistance: ISO 7840 Annex A: hose filled with fuel should withstand flame for 2.5 min). Inner layer: black synthetic rubber. Reinforcement: synthetic braid. Outer layer: black synthetic rubber. Working pressure: from 2.5 bar to 3.4 bar - depending on hose diameter. Operating temperature: from -20°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong fuel transfer hose for aviation fuel, designed for direct pressure refueling of aircraft on the ground. It can also be used in fuel transfer operations in airport tankers – dispensers, in operations not requiring high vacuum. Specifically designed for kerosene (aviation fuel - fuel for turbine aircraft engines, e.g., JET A1), aviation gasoline, and fuels with aromatic hydrocarbon content up to 50%. Can be used on drum reels. Inner layer made of black, smooth, antistatic NBR rubber. Reinforcement with layers of high-strength synthetic cord. Outer layer made of black, antistatic, self-extinguishing chloroprene (CR) rubber, resistant to abrasion, contact with hydrocarbons, and weather conditions. Antistatic outer layer, in accordance with EN ISO 1825 requirements, ensures the required low resistance of the hose between the ends (103 Ω ‹ R ‹ 106 Ω, ISO 8031). Compliant with requirements for aviation fuel hoses (type C/Ω) EN ISO 1825, EN 1361, BS 3158, EI 1529. Inner layer: black NBR rubber. Reinforcement: synthetic cord. Outer layer: black CR rubber. Working pressure: 20 bar. Operating temperature: from -30°C to +70°C (for aviation fuel according to EN 1825).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, soft rubber hose with an external stainless steel braid, designed for gasoline and petroleum-based oils such as diesel, heating oil, and lubricating oil. Installed in fuel and oil systems of small vehicles and industrial equipment. Can also be used for water, cooling fluids, non-oxidizing detergents, and air. Based on the requirements of standard DIN 73379. Inner layer made of smooth black NBR rubber. The external reinforcing braid made of stainless steel provides high pressure resistance and is corrosion-resistant. Maximum operating temperature depends on the medium: for gasoline, unleaded gasoline, fuels with up to 50% aromatic hydrocarbon content: +40ºC; for diesel: +80ºC; for water and ethylene glycol-based cooling liquids: +90ºC; for air: +80ºC; for liquid, non-oxidizing detergents: +80ºC. Inner layer: black NBR rubber. Reinforcement: external wire braid made of stainless steel AISI 304. Working pressure: from 10 bar to 20 bar - depending on the hose diameter. Operating temperature: from -35°C to +80°C (maximum operating temperature depends on the medium).
