Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsMedium thickness, flexible hose designed for the removal of dust, wood shavings, chips, cuttings, lightweight bulk materials, etc. Specifically designed according to the requirements of the woodworking and furniture industries, it can also be used in other industrial fields. Compliant with DIN 26057 Type 2. Antistatic and flame-retardant, ensuring high workplace safety. Less flexible and compressible than SMARTFLEX® 0.4 and 0.6, but smooth inside, flexible even at low temperatures. With very good abrasion resistance, also resistant to microbes and hydrolysis. Free from halogen compounds and plasticizers. Resistant to oils and gasoline. The optimal direction of medium flow is marked with an arrow. The wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. Antistatic properties: permanently antistatic (according to ISO 8031 resistance R <109 Ω, according to German technical regulations TRGS 727 (6.4.2.4) specific resistance R < 2.5 x 108 Ωm, according to directive 2014/34/EU (ATEX) can be used in specific explosion hazard zones - which must be preceded by a risk analysis). After effective double grounding of the spiral, it can be treated as electrically conductive – in accordance with BGI 739-2 recommendations. Flame-retardant – according to DIN 4102 class B1. Hose material: transparent polyester-polyurethane. Wall thickness measured between the spiral: 0.7 mm. Reinforcement: steel wire spiral. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction and discharge hose designed for the transfer of food substances, requiring the use of odorless and tasteless rubber. It contains no phthalates or bisphenol A. Thanks to the steel spiral reinforcement, it has good resistance to vacuum. Suitable for milk and its derivatives, as well as wine, beer, and fruit juices. Not recommended for oils and fatty food substances. Widely used in the food industry. The outer layer of the hose is resistant to abrasion and weather conditions. Standards and requirements: Food industry, contact with food: 1935/2004/EC and 2023/2006/EC (GMP). D.M. 21/03/73, FDA 21 CFR 177.2600, BfR XXI cat. 2. Inner layer: white natural rubber (NR). Reinforcement: synthetic cord, steel spiral. Outer layer: blue EPDM rubber. Working pressure: 6 bar. Operating temperature: from -25°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTranslucent, yellow, flexible hose designed specifically for fuel and lubricating oils. Resistant to swelling and hardening due to hydrocarbon exposure, significantly reduces the risk of cracking and leakage. Minimal extractability ensures fuel cleanliness, and low permeability to aromatic substances protects the operator and the environment. Ozone and UV radiation resistant. The flexibility of the hose facilitates installation even in tight spaces. The translucent wall allows for flow monitoring. The hose is resistant to most petroleum products and fuels (including those with up to 10% ethanol) and can be used for gasoline, kerosene, diesel, heating oil, lubricants, cutting fluids, and glycol-based fluids. Widely used and proven in thousands of applications: small engines, automotive, recreational vehicles, lawn mowers, saws, cooling and lubrication systems, cutting and polishing equipment. Full hose roll length: 15 m. Working pressure defined relative to burst pressure with a safety factor of 1:5. Material: PVC (special). Maximum operating temperature: +74°C. Brittleness temperature: -37°C. Hardness: 57° Shore (A). Density: 1.26 g/cm³. Note: Product packaged in the Clean Zone of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight, flexible suction and discharge hose designed for the transfer of chemical substances. Made from thermoplastic vulcanizate TPV – a material that combines the processing advantages of thermoplastic polymers (PP – polypropylene) with the properties of vulcanized rubber (EPDM). Good chemical resistance - similar to EPDM rubber allows for use with many substances, including acids (hydrochloric, sulfuric), bases, salts, alcohols, glycols, and ketones, concentrated detergents. Not recommended for fuels, oils, aromatic solvents. Resistant to weather conditions, aging, and abrasion (abrasion resistance according to ISO 4649:150 mm³). Low weight and small bending radius of the hose ensure ease of handling, which can be an advantage when transferring from tankers and containers. A special version, VACUPRESS SUPER CHEMI (diameters up to 63 mm), is available on special order with an inner layer lined with polyethylene (LLDPE), which increases the chemical resistance of the hose and allows its use with concentrated hydrochloric and sulfuric acids, nitric acid, as well as aggressive herbicides and insecticides. Inner layer: thermoplastic rubber TPV. Reinforcement: polyester braid, galvanized steel spiral. Outer layer: thermoplastic rubber TPV. Working pressure for temperature +20°C: from 7 to 15 bar - depending on the diameter of the hose. Operating temperature: from -25°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe HYPERLINE FX hose is an optimal solution for industrial applications where high flow rates, chemical and temperature resistance, and permeation resistance are required. It is perfectly suited for the transfer of chemicals, fuels, oils, paints, solvents, adhesives, dyes, gases, and steam, detergents, water, and food substances. At operating temperatures above +130°C, the maximum working pressure specified in the table should be reduced by 1% for each 1°C above this temperature. For example, at a temperature of 170°C, the maximum working pressure for the hose AF-FXAM-10 is: 70 bar – (170°C-160°C) x 1 = 70 bar – 40% = 42 bar. In cases where a substance that is a poor conductor and has potential electrification properties flows through the PTFE hose, the electric charge will accumulate on the inner surface of the PTFE, and to avoid static electricity issues, an antistatic AS variant of PTFE is used. Antistatic Teflon in the AS version contains appropriately distributed graphite in the PTFE and has a resistance R <108 Ω (according to ISO 8031 annex A). Hose material: smooth inside, corrugated outside PTFE (Teflon) - natural white and antistatic - black. Reinforcement: aramid braid. Working pressure: from 35 bar to 77 bar - depending on the hose diameter. Operating temperature: from -70°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, semi-transparent, reinforced flexible hose made of platinum-cured silicone rubber. Designed for higher pressures. Used in the pharmaceutical, cosmetic, food, biotechnology industries, sterile filling lines, water treatment systems, vaccine production, bioreactors. Characterized by an exceptionally smooth internal surface that prevents the deposition and adhesion of contaminants inside the hose and the development of bacteria. This facilitates complete cleaning and sterilization of the hose. The smooth internal layer also reduces flow resistance through the hose. Low extractability, non-toxicity, non-hemolytic, and non-pyrogenicity ensure total fluid purity in sensitive applications. Minimal biological load (bioburden). Meets hygienic requirements of the American FDA 21 CFR 177.2600, 3-A, and USP Class VI. Sterilization possible by steam (30 min, 1 bar, 121°C), CIP and SIP cleaning of installations, ethylene oxide, or radiation (up to 5 Mrad). Full hose roll length 15 m (from internal diameter 31.8 mm – 7.5 m). Working pressure defined relative to burst pressure with a safety factor of 1:4. Material: silicone (platinum). Maximum operating temperature: up to +160°C. Brittleness temperature: -80°C. Hardness: 70° Shore (A). Density: 1.18 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible, thick hose designed for the removal of sawdust, chips, shavings, bulk materials, etc. Specifically designed according to the requirements of the woodworking and furniture industries, it can also be used in other industrial fields. Compliant with DIN 26057 Type 3. Antistatic and flame-retardant, ensuring high work safety. Thick wall and dense reinforcing spiral provide high pressure parameters. Very smooth inside, low compressibility. Flexible even at low temperatures. Excellent abrasion resistance, also resistant to microbes and hydrolysis. Free of halogen compounds and plasticizers. Resistant to oils and gasoline. The optimal flow direction of the medium is marked with an arrow. The wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. Antistatic properties: permanently antistatic (according to ISO 8031 resistance R <109 Ω, according to German technical regulations TRGS 727 (6.4.2.4) specific resistance R < 2.5 x 108 Ωm, according to directive 2014/34/EU (ATEX) can be used in specific explosion hazard zones - which must be preceded by a risk analysis). After effective double grounding of the spiral, it can be treated as electrically conductive – in accordance with BGI 739-2 recommendations. Flame-retardant – according to DIN 4102 class B1. Wall thickness measured between the spiral: 1.4 mm. Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction and discharge hose with an inner layer made of chemically resistant polyethylene with ultra-high molecular weight (UPE, UHMWPE). The inner layer is resistant to most acids and bases as well as many other aggressive chemicals (at elevated but not very high temperatures), making the hose widely used in the chemical and petrochemical industries. The UPE inner layer also complies with food-grade hose requirements, is free from phthalates and polycyclic aromatic hydrocarbons (PAH), and features a low friction coefficient during flow, preventing medium deposition on the walls. This significantly facilitates cleaning and allows for use in the cosmetic, pharmaceutical, and food industries as well. Reinforced with synthetic cord and steel spiral, with built-in copper wires for electrostatic discharge. The outer layer is made of chemically resistant EPDM rubber, resistant to abrasion, ozone, and weather conditions. Compliant with EN 12115:11 requirements (type M, resistance between hose ends R ≤ 100 Ω, guaranteed for hoses up to 40 m in length). Standards and requirements: Chemical hoses: EN 12115:2011. Food industry, contact with food (inner layer): 1935/2004/EC, 2023/2006/EC (GMP), 10/2011/EU (simulant fluids A, B, D2), FDA 21 CFR 177.1520, BfR III. Confirmation of resistance and application conditions requires contact with Tubes International, especially for temperatures above 50°C. Inner layer: white creamy UPE polyethylene. Reinforcement: synthetic cord, steel spiral. Outer layer: black EPDM rubber. Working pressure: 16 bar. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible suction and discharge hose with an inner layer made of abrasion and oil-resistant polyurethane, reinforced with a densely arranged steel spiral to increase working pressure and resistance to vacuum. Designed for air, liquids, light chemicals, in pneumatic and hydraulic systems, as well as for the transport of solid substances. The smooth inner surface reduces flow losses and ensures ease of cleaning. The transparent wall allows for visual flow monitoring. Reinforcement with a dense steel wire spiral provides very good resistance to vacuum and hose collapse, as well as a small bending radius. In general industrial applications, it can be used for water, light chemicals, and other fluids based on fats, oils, and hydrocarbons (chemical resistance of polyurethane should be considered) and for air, for vacuum transport of dust, powders, granules, and other abrasive bulk materials (abrasiveness of the medium and potential static electricity issues should be considered). It can be used in the food industry (where American FDA 21 CFR 177.2600 e, f requirements are acceptable) for liquid food substances for hydrated food ("e") and fatty food ("f"). Inner layer: transparent polyurethane. Reinforcement: steel spiral. Outer layer: transparent PVC. Working pressure at 20°C: from 12 bar to 20 bar - depending on the hose diameter. Operating temperature: from -20°C to +90°C. As the operating temperature increases, the working pressure value of the hose decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe Hyperline FX SS RC BLACK hose is a lightweight, flexible Teflon hose, featuring an additional outer layer made of black, antistatic, and flame-retardant EPDM rubber, meeting the requirements for railway vehicles EN 45545. This provides extra protection for the braid and hose against damage and allows for easy cleaning of the hose. Due to its properties, it is recommended for use in the industrial sector and mechanical vehicles. The hose can be supplied without fittings or as complete assemblies ready for installation. Hose material: smooth on the inside, corrugated PTFE (Teflon) on the outside. Reinforcement: single braid of AISI 304 steel with an additional protective layer of EPDM rubber. Working pressure: from 50 bar to 110 bar, depending on the hose diameter. Operating temperature: from -40°C to +140°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible, bendable, and nearly smooth inside hose designed for suction and transport of light materials with abrasive properties, such as dust, powders, granules, grains, flakes, and similar substances under low pressure. The hose is made of polyether-polyurethane and has good resistance to abrasion, ozone, weather conditions, hydrolysis, and biological corrosion. It is suitable for contact with food for the transport of bulk, dry food materials. It complies with European regulations 1935/2004/EC and 10/2011/EU (simulant E), 1895/2005/EC, 2023/2006/EC (GMP), and American FDA 21 CFR 177.2600 "d". It is suitable for temporary contact with food during the transport of dry, bulk, non-fatty food substances - under conditions specified in the manufacturer's declaration of conformity (available from Tubes International). Reinforcement with a hard PVC spiral provides good crush resistance. Used in various industrial applications, particularly in the food and agricultural industry, plastics, construction materials, etc. Versions: standard and antistatic - featuring a copper antistatic wire embedded on the outer side of the hose along the reinforcing spiral. Effective grounding of the wire ensures a sufficient level of electrostatic charge dissipation for many applications. The specified wall thickness of the hose is measured between the spiral. Hose material: transparent polyether-polyurethane. Reinforcement: hard PVC spiral. Operating temperature: from -25°C to +85°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, transparent, flexible hose completely free of plasticizers for chemical and food applications - requiring high chemical resistance due to the nature of the substances (e.g., wine - alcohol, acids - orange juice) or used cleaning and disinfecting agents. Resistant to acids, bases, salts, alcohols, and ketones, with very low levels of absorption and adsorption. This minimizes the risk of changing the properties, taste, and smell of the fluid even with repeated use of the hose. The glassy smooth, pore-free inner surface prevents the deposition and adherence of contaminants inside the hose and facilitates cleaning. Resistant to chemical cleaning and disinfecting agents. Not recommended for hydrocarbons. Meets hygiene and food contact requirements: European 1935/2004/EC and 10/2011 EU (for conditions and substances according to certification), American FDA 21 CFR 177.1520, NSF-51. Possible sterilization with ethylene oxide or radiation (up to 2.5 Mrad). Compliant with REACH - does not contain hazardous and prohibited substances. Proper incineration of used hoses does not release hazardous substances (e.g., hydrochloric acid). The hose is used for both food substances (e.g., wine dispensing) and chemical applications: detergent installations, ink dispensing, acid filling for batteries, chemical analyzers. Full hose roll length 15 m (for internal diameter 25.4 mm - 7.5 m). The specified working pressure is defined relative to the burst pressure with a safety factor of 1:5. Material: polyolefin. Operating temperature: from -75°C to +54°C. Brittleness temperature: -75°C. Hardness: 75° Shore (A). Density: 0.90 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible, suction and pressure hose designed for the pressurized transfer of water, beer, wine, alcohols with a concentration of up to 20%, juices, beverages, other liquid food substances, and light chemicals. Not recommended for milk and its derivatives, oils, and fatty food substances. Reinforcement with a galvanized steel wire spiral embedded in the inner layer of PVC provides good resistance to vacuum and hose collapse. The smooth inner layer reduces flow losses and ensures ease of cleaning. Thanks to the braided reinforcement, the hose has high pressure resistance and low deformation under pressure. Standards and requirements: Food industry, food contact: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B, and C), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: polyester braid, steel spiral. Working pressure: from 10 bar to 20 bar, depending on the hose diameter. Vacuum: 0.9 bar. Operating temperature: -5°C to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery flexible and elastic, universal suction and discharge hose intended for water, liquids, and light chemicals. Used for loading and unloading tankers, pallet containers, and for liquid transfer in industrial installations, etc. Maintains high flexibility at low ambient temperatures. The smooth inner wall facilitates hose cleanliness and increases discharge efficiency by 20% compared to typical rubber hoses. The outer layer is resistant to abrasion and weather conditions. In the food industry, it can be used for the transfer and handling of hydrated, acidic food, and alcohols up to 20%, e.g., juices, beverages, beer, wine (simulants A, B, C; up to +40°C and 2 hours). Not recommended for milk and its derivatives, as well as oils and fatty food substances. The VACUPRESS SUPERELASTIC hose complies with European requirements 1978/142/EEC, 1935/2004/EC, 1895/2005/EC, and 10/2011/EU (simulants A, B, C), 2023/2006/EC (GMP). Suitable for temporary contact with food during the transfer of food substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International). Inner layer: white PVC. Reinforcement: steel spiral, polyester braid. Outer layer: black PVC. Working pressure for a temperature of 20°C: from 5 bar to 20 bar - depending on the hose diameter. Operating temperature: from -25°C to +60°C. As the operating temperature increases, the working pressure value of the hose decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, transparent, strong, and flexible hose made of polyester-polyurethane, free of plasticizers, exceptionally resistant to abrasion and tearing, characterized by flexibility even at low temperatures and withstands cyclic temperature changes. The hose is produced with strict dimensional tolerances from batch to batch, ensuring safe, repeatable connections with fittings. Resistant to oils, greases, fuels, and a range of chemicals. Durable against weather conditions and intensive daily use. It is used in various industrial sectors: fuel and lubrication systems, for cooling fluids in automotive applications, for air in pneumatics and industrial automation, for the transfer of abrasive and viscous products, sludges, and powders, as well as for electrical hose protection. Full hose roll length is 30 m. Working pressure defined relative to burst pressure with a safety factor of 1:5. Material: tygothane® - polyurethane-polyester (PU). Operating temperature: from -73°C to +79°C (temporarily up to +93°C). Brittleness temperature: -73°C. Hardness: 82° Shore (A). Density: 1.20 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMedium thickness, strong and flexible hose designed for the removal of sawdust, chips, shavings, light bulk materials, etc. Specifically designed according to the requirements of the woodworking and furniture industries, it can also be used in other industrial fields. Antistatic and flame-retardant, it ensures high work safety. Less flexible and compressible than SMARTFLEX® 0.4, 0.6, and 0.7, but smooth inside, flexible even at low temperatures. With very good abrasion resistance, also resistant to microbes and hydrolysis. Contains no halogen compounds or plasticizers. Resistant to oils and gasoline. The optimal direction of medium flow is marked with an arrow. The wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special order. Antistatic properties: permanently antistatic (according to ISO 8031 resistance R <109 Ω, according to German technical regulations TRGS 727 (6.4.2.4) specific resistance R < 2.5 x 108 Ωm, according to directive 2014/34/EU (ATEX) can be used in specific explosion hazard zones - which must be preceded by a risk analysis). After effective double grounding of the spiral, it can be treated as electrically conductive – in accordance with BGI 739-2 recommendations. Flame-retardant – according to DIN 4102 class B1. Wall thickness measured between the spiral: 1.0 mm. Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery flexible, lighter than rubber, suction and discharge hose designed for the transport of water, sewage, sludge, and dry bulk materials. Used in irrigation systems, loading and unloading of tankers, in industrial installations, etc. Maintains high flexibility at low ambient temperatures. The smooth inner and outer wall facilitates hose cleanliness and increases discharge efficiency by 20%. It is resistant to weather conditions and abrasion. The hose is also available in straight, non-curved sections of 3 to 6 m. Inner layer: black PVC. Reinforcement: polyester braid, galvanized steel spiral. Outer layer: black PVC. Working pressure: from 5 bar to 16 bar - depending on the hose diameter and temperature. Operating temperature: from -25°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible suction and discharge hose designed for water, juices, beverages, beer, wine, alcohols with a concentration of up to 20%, and other food products. Not recommended for milk and its derivatives, oils, and fatty food substances. Reinforced with a hard PVC spiral, impact-resistant, providing good resistance to vacuum and hose collapse. The transparent wall allows for easy visual monitoring of flow. The smooth inner surface reduces flow losses and ensures ease of cleaning. The outer surface is slightly corrugated. In applications not involving direct contact with food (in industry, construction, agriculture), it can be used: 1) for light chemicals, water, sludges, and wastewater, other liquids (without fats, oils, and hydrocarbons); 2) for air, vacuum transfer of dust, powders, granules, and other lightly abrasive bulk substances (non-fatty). Abrasiveness and potential static electricity issues should be considered. Standards and requirements: Food industry, contact with food: compliant with European regulations 1935/2004/EC and 10/2011/EU (simulant fluids A, B, and C), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: hard PVC spiral. Working pressure: from 2 bar to 7 bar, depending on hose diameter. Operating temperature: from -10°C to +55°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight, flexible suction and discharge hose designed for the transfer of chemical substances. Made from thermoplastic vulcanizate TPV – a material that combines the processing advantages of thermoplastic polymers (PP – polypropylene) with the properties of vulcanized rubber (EPDM). Good chemical resistance - similar to EPDM rubber allows for use with many substances, including acids (hydrochloric, sulfuric), bases, salts, alcohols, glycols, and ketones, concentrated detergents. Not recommended for fuels, oils, aromatic solvents. Resistant to weather conditions, aging, and ozone. Low weight and small bending radius of the hose ensure ease of handling, which can be an advantage when transferring from tankers and containers. Note: All hose sizes have branding indicating approximate working pressure (WP 10 bar). Confirmation of resistance and application conditions requires contact with Tubes International. Inner layer: thermoplastic rubber TPV. Reinforcement: polyester braid, steel spiral. Outer layer: thermoplastic rubber TPV. Working pressure for temperature +23°C: from 12 to 14 bar - depending on hose diameter. Operating temperature: from -30°C to +80°C (working pressure dependent on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, transparent, soft, and highly flexible hose with exceptionally long service life for use in peristaltic pumps (LFL - "long flex life"). It has high fatigue resistance and exceptional spallation resistance (spallation - chipping of hose material particles due to pump rotor pressure). One of the best TYGON® hoses for peristaltic pumps - service life of 1000 hours (at back pressure of 0 bar). Resistance to particle spallation eliminates the need for frequent filter replacement and minimizes the risk of contamination. Suitable for high-viscosity fluids, viscous fluids, and shear-sensitive fluids. Widely used in the food, cosmetic, pharmaceutical, and chemical industries, in production and laboratories. The hose is free from phthalates and BPA (Bisphenol A). It meets hygiene and food contact requirements: European 1935/2004/EC and 10/2011 EU (for conditions and substances according to certification), American FDA, NSF, USP Class VI, international ISO 10993, Japanese #370/1959. Sterilization by steam or ethylene oxide is possible. Compliant with REACH and California Proposition 65 - does not contain hazardous and prohibited substances. Full hose roll length is 7.5 m (from internal diameter 19 mm - 3 m). Working pressure defined relative to burst pressure with a safety factor of 1:5. Material: PVC (special). Maximum operating temperature: up to +74°C. Brittleness temperature: -46°C. Hardness: 56° Shore (A). Density: 1.17 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible, pliable, and nearly smooth inside hose made of soft polyvinyl chloride (PVC) reinforced with a right-handed spiral of hard PVC. Designed for the removal of dust, smoke, fibers, extraction of contaminated air, etc. Also used for condensate drainage in air conditioning systems and as protection for wires and hoses. Hose installation with clamps on appropriate ends, pipe fittings, etc. Wall thickness of the hose is measured between the spiral. Hose material: gray, soft PVC. Reinforcement: spiral of hard PVC. Operating temperature: from -15°C to +60°C (operating vacuum dependent on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight and flexible suction and discharge hose intended for water, juices, beverages, beer, wine, alcohols with a concentration of up to 20%, and other food products. Not recommended for milk and its derivatives, oils, and fatty food substances. Reinforced with a hard PVC spiral, resistant to impacts, providing good resistance to vacuum and hose collapse. The transparent wall allows for easy visual monitoring of flow. The smooth inner surface reduces flow losses and ensures ease of cleaning. The outer surface is slightly corrugated. In applications not involving direct contact with food (in industry, construction, agriculture), it can be used for light chemicals, water, sludges and sewage, other liquids (without fats, oils, and hydrocarbons), as well as for air, vacuum transfer of dust, powders, granules, and other lightly abrasive bulk substances (non-fatty). Abrasiveness and potential static electricity issues should be considered. Available in an antistatic version LUISIANA AS - additionally features a copper wire embedded in the hose material parallel to the PVC spiral, which, when connected to the installation and grounded, ensures the discharge of electrostatic charges. This version is available on special order, example index for the antistatic version: e.g., ME-LUISIANA-AS-050. Standards and requirements: Food industry, contact with food: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B, and C), 2023/2006/EC (GMP). Hose material: transparent yellowish PVC. Reinforcement: hard PVC spiral. Working pressure: from 2 bar to 8 bar, depending on the hose diameter. Operating temperature: from -5°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and pressure hose of the latest generation specially designed according to the high requirements of the beer processing industry. It is intended for the transfer of high-quality raw beer, pasteurized beer, and organic beer. The inner layer is completely free of phthalates, plasticizers, and animal-derived components, eliminating the risk of medium contamination and bacterial growth. The outer layer is resistant to abrasion, aging, and weather conditions. Tested and approved for beer transfer by the Technical University of WEIHENSTEPHAN in Munich – does not alter the taste of the beer. Standards and requirements: 1) General: EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) Food industry, food contact: 1935/2004/EC, 2023/2006/EC (GMP). Inner layer compliant with FDA 21 CFR 177.2600, D.M. 21/03/73, 3-A n. 18-03-Class II. Inner layer: white bromobutyl rubber (BIIR). Reinforcement: synthetic cord, steel spiral. Outer layer: red CR rubber. Working pressure: 10 bar. Operating temperature: -40°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight, extremely flexible and elastic hose designed for the removal of dust, powder, contaminated air, fumes, vapors, etc. Thanks to its unique construction with longitudinal and transverse reinforcement made of synthetic fibers and a steel spiral, it features a very small bending radius, resistance to kinking, and exceptional tensile strength. Durable and reliable, widely used in industrial and household vacuum systems, in construction work for cleaning and drying, and as a protective hose. Cadmium-free in accordance with BGR 132. Discharge of electric charges through grounding of the steel spiral. The left-handed reinforcing spiral allows for the attachment of appropriate fittings for vacuum cleaners with a left-hand thread (PVC fittings for the SUPERELASTIC hose or other suitable ones). Hose mounting with clamps on appropriate ends, pipe fittings, etc. Hose material: two layers of soft PVC reinforced with fiber. Reinforcement: steel spiral coated with PVC. Operating temperature: from 0°C to +85°C (operating pressure dependent on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality suction and discharge hose designed for the transfer of aggressive chemical substances, solvents, and concentrated chemicals, characterized by high thermal and mechanical strength and the highest purity of the inner layer. The inner layer is made of white perfluoroalkoxy polymer MFA (fluoropolymer with properties similar to Teflon), mirror-smooth (prevents medium deposition on the walls and is easy to clean), odorless and tasteless, meeting high hygiene requirements (FDA, USP, European EU). Intermediate layers made of synthetic rubber, reinforced with synthetic cord, and a steel wire spiral. The outer layer is made of EPDM rubber, antistatic (R<106 Ω), abrasion-resistant, ozone-resistant, and weather-resistant. The hose features excellent chemical resistance and purity of MFA, impermeability, temperature resistance, oxidation resistance, and mechanical stress resistance. Widely used in the chemical industry due to its total resistance to most chemical substances. Suitable for the transfer of concentrated acids and alkalis (sulfuric acid, hydrochloric acid, phosphoric acid, nitric acid, sodium hydroxide, potassium hydroxide, etc.). Resistant to rigorous cleaning conditions using the Cleaning-in-Place (CIP) method. On special order, version M according to EN 12115 with two built-in copper wires for discharging electric charges. Standards and requirements: Chemical hoses: EN 12115:2011 (type Ω). Food industry, contact with food: 1935/2004/EC, 2023/2006/EC (GMP); inner layer: 10/2011/EU, USP Class VI, FDA 21 CFR 177.1550 (e-i); ISO 10993. Does not contain plasticizers, phthalates, or animal-derived substances. Assembly: use smooth fittings with a spigot ("tail" for the hose) that do not have sharp or high ribs that could cut or damage the inner layer made of MFA when tightened. The diameter of the spigot should be precisely matched to the diameter of the hose to ensure tightness. Assembly with clamp sleeves or shell clamps. Confirmation of resistance and application conditions requires contact with Tubes International. Inner layer: white MFA polymer. Reinforcement: synthetic cord, steel spiral. Outer layer: black EPDM rubber. Working pressure: 16 bar. Operating temperature: from -50°C to +170°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSUPERFLEX RADIATOR hose connector designed for engine cooling systems in vehicles and automotive-type engines (for water, ethylene glycol-based coolants). Version with textile reinforcement and a steel spiral to prevent collapse of the bent hose. It features "soft" ends, free of steel spiral, allowing for easy and tight installation on fittings using clamps. The externally corrugated design of the hose bends easily, replacing the original molded connector in many cases and ensuring uninterrupted full flow even with strong bends. The connector design complies with SAE J20 R5 standard and is resistant to temperature and coolants used in automotive applications. No data on working pressure. Operating temperature: from -40°C to +125°C. Connector material: black EPDM rubber. Reinforcement: textile braid + steel spiral.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight and flexible hose designed for the transport of air, dust, powders, fine wood shavings and chips, very light bulk materials, etc. Specifically designed according to the requirements of the woodworking and furniture industries, it can also be used in other industrial fields. Compliant with DIN 26057 Type 1. Antistatic and flame-retardant, ensuring high workplace safety. Very flexible and compressible, also elastic at low temperatures. With very good abrasion resistance, also resistant to microbes and hydrolysis. Free from halogen compounds and plasticizers. Resistant to oils and gasoline. The optimal flow direction of the medium is indicated by an arrow. The wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. Antistatic properties: permanently antistatic (according to ISO 8031 resistance R <109 Ω, according to German technical regulations TRGS 727 (6.4.2.4) specific resistance R <2.58 Ωm, according to directive 2014/34/EU (ATEX) can be used in specific explosion hazard zones - which must be preceded by a risk analysis). After effective double grounding of the spiral, it can be treated as electrically conductive – in accordance with BGI 739-2 recommendations. Flame-retardant – according to DIN 4102 class B1. Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Wall thickness measured between the spiral: 0.4 mm. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, colorless, transparent, flexible hose that is odorless and tasteless, non-toxic, and free of DEHP phthalates. Specifically designed for use in peristaltic pumps. Used for dispensing and portioning cold and hot food products, for soaps and detergents, for paints, and in laboratories. The soft hose material (60° Shore (A)) is highly flexible and provides excellent longevity of over 500 hours of operation in a peristaltic pump. The hose is a good alternative to commonly used PVC or silicone hoses. It remains flexible even at -40°C and withstands elevated temperatures up to +121°C. It has good chemical resistance to a range of chemicals, such as acids and bases. Not recommended for fats, high-proof alcohols, and hydrocarbons. Resistant to ozone, oxygen, and sunlight, and is difficult to ignite. Characterized by low extractability (migration of material components into the medium). Meets hygiene and food contact requirements: European 10/2011 EU (for conditions and substances according to certification), American FDA, NSF-51. Sterilization possible by steam, ethylene oxide, or radiation. Full hose roll length: 15 m. Working pressure specified relative to burst pressure with a safety factor of 1:5. Material: tygoprene® - thermoplastic elastomer styrene (TPE). Maximum operating temperature: up to +121°C. Brittle temperature: -66°C. Hardness: 60° Shore (A). Density: 0.9 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLow-pressure suction and discharge hose with a transparent inner layer made of chemically resistant PFA and a thick outer layer made of transparent silicone. Designed for various applications in the pharmaceutical, cosmetic, food, and chemical industries, where, in addition to the highest purity, aseptic conditions, and chemical resistance, observation of medium flow is required. The inner layer is made of perfluoroalkoxy polymer PFA (fluoropolymer with properties similar to Teflon), transparent, mirror-smooth, odorless and tasteless, chemically inert, meeting high hygiene requirements (FDA, USP, European EU). Reinforcement with a stainless steel spiral provides good resistance to vacuum. The thick outer layer made of platinum-cured silicone with a smooth surface features non-stick properties (the hose does not "stick") and a low coefficient of friction. It can be easily cleaned using a mild detergent. The hose design combines the advantages of PFA with the flexibility of silicone and its temperature resistance. The hose has a small minimum bend radius, is flexible and elastic at low and elevated temperatures, resistant to cyclic bending according to ASTM D 2176 and dynamic loads. Standards and hygiene requirements: inner layer: USP Class VI, 3-A Sanitary Standards 18-03 Class I, 10/2011/EU, FDA, ISO 10993-4, -10, -11, non-cytotoxic (ISO 10993 Part 5), ICH Q3D; outer layer: USP Class VI, 3-A Sanitary Standards 18-03 Class I, D.M. 21/03/73, FDA, BfR, European Pharmacopoeia 3.1.9, ISO 10993-4, -10, -11, non-cytotoxic (ISO 10993 Part 5). The hose complies with 1935/2004/EC, 2023/2006/EC (GMP), manufactured in Cleanroom ISO 14644-1 Class 8, free from phthalates, adipates, nitrosamines, animal-derived substances, substances subject to EC 1907/2006 (REACH). Confirmation of resistance and conditions of use requires contact with Tubes International. For confirmation of resistance and conditions of use, please contact Tubes International. Installation: use fittings with a smooth spigot ("tail" for the hose) that do not have sharp or high ribs that could cut or damage the inner PFA layer when tightened. The diameter of the spigot should be precisely matched to the diameter of the hose to ensure sealing. Installation with clamp sleeves or bands (clamps). Inner layer: transparent PFA polymer. Reinforcement: AISI 302 stainless steel spiral. Outer layer: transparent silicone. Working pressure: from 1 bar to 3 bar, depending on the hose diameter. Operating temperature: from -30°C to +150°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible, and smooth hose made of soft polyvinyl chloride (PVC) with small internal grooves, reinforced with a right-hand spiral of hard PVC. Designed for the extraction of contaminated air, smoke, dust removal, chips, fibers in the textile industry, etc. Widely used in various industrial applications. Self-extinguishing and flame-retardant, in accordance with the American flammability class UL 94 V-2. Hose installation with clamps on appropriate ends, pipe fittings, etc. Wall thickness is measured between the spiral. Hose material: soft gray PVC. Reinforcement: spiral of hard PVC. Operating temperature: from -10°C to +60°C (working vacuum dependent on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible suction and discharge hose designed for the transfer of water, juices, beverages, and other food products at temperatures up to +40°C. The absence of phthalates in the hose material makes it suitable for the transfer of milk and its derivatives, as well as alcohols with concentrations up to 50% and temperatures up to +40°C. Not recommended for oils and fatty food substances. Reinforcement with a steel wire spiral embedded in a soft PVC wall provides good resistance to vacuum and hose collapse. The smooth inner wall reduces flow losses and ensures ease of cleaning. The transparent wall resistant to UV radiation allows for easy visual monitoring of flow. In applications not involving direct contact with food (in industry, construction, agriculture), it can be used: 1) for light chemicals, water, sludges, and wastewater, other liquids (without fats, oils, and hydrocarbons); 2) for air, vacuum transfer of dust, powders, granules, and other lightly abrasive bulk materials (non-fatty). Abrasiveness and potential static electricity issues should be considered. As a hose reinforced only with a steel spiral (without a braid), it exhibits some elongation under pressure, which should be taken into account in applications, especially at temperatures above +40°C. Standards and requirements: Food industry, contact with food: compliant with European regulations 1935/2004/EC and 10/2011/EU (simulants A, B, C, and D1), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: galvanized steel spiral. Working pressure: from 2 bar to 12 bar, depending on the hose diameter. Vacuum: 0.9 bar. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsExceptionally flexible and elastic suction and discharge hose designed for the transport of food substances, requiring the use of odorless and tasteless rubber. It contains no phthalates or bisphenol A. Suitable for milk and its derivatives, as well as wine, beer, and fruit juices. Not recommended for oils and fatty food substances. Commonly used in tankers for the transfer of milk. Due to its high flexibility, it can be used with drum reels. The outer layer of the hose is resistant to abrasion and weather conditions. Standards and requirements: Food industry, contact with food: 1935/2004/EC and 2023/2006/EC (GMP), D.M. 21/03/73, FDA 21 CFR 177.2600, BfR XXI cat. 2. Inner layer: white natural rubber (NR). Reinforcement: synthetic cord, steel spiral. Outer layer: blue EPDM rubber. Working pressure: 6 bar. Operating temperature: -25°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible medium-thickness hose designed for the transport of chips, bulk materials, granules, etc. Suitable for all types of industries, particularly commonly used for the removal of chips and other solid particles in the woodworking, furniture, ceramics, and plastics industries. The medium-thick wall and dense reinforcing spiral provide higher pressure parameters compared to ECO hoses 0.4, 0.6, and 0.7. Very smooth on the inside, low compressibility, and flexible - even at low temperatures. Good abrasion resistance, also resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. The hose is marked with an arrow indicating the correct direction of medium flow. The wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. The hose is available in the following versions: ECO – standard version, ECO SE – flame-retardant material version (UL94 V-2), ECO AS – permanently antistatic version (ISO 8031: R <109 Ω, TRGS 727 (6.4.2.4): R <2.5 x 108 Ωm, directive 2014/34/EU (ATEX): can be used in specific explosion hazard zones after risk analysis), ECO SE AS – antistatic and flame-retardant version (available on special order). The ECO hose is produced in a manufacturing process compliant with sustainable development policies, using raw materials from recycled clean waste from the production process, renewable energy, closed water circulation, and other innovations. Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Wall thickness measured between the spiral: 1.0 mm. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose with steel spiral reinforcement, intended for hot water mixed with antifreeze fluids. Used in cooling and heating systems, for pumps in engines and machines. It has vacuum resistance. Inner layer resistant to heat and cooling fluids. Outer layer resistant to heat and aging. Rubber mixture compliant with DIN 73411:79 standard. Inner layer: black EPDM rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black EPDM rubber. Working pressure: 4 bar. Operating temperature: from -40°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCrystal clear, flexible, and completely biocompatible medical hose free of phthalates (DEHP). Intended for use in dialysis equipment, blood transfusion and drainage, infusion, chemotherapy, inhalation, minimally invasive procedures, catheters, and medical laboratories. Can be used with peristaltic pumps, but lifespan is limited. High transparency of the hose and non-wettability of the inner surface ensure good flow visualization and easy complete drainage of the hose. Can be connected with mechanical clamps, thermally welded, ultrasonically welded, or glued. Compliant with ISO 10993, European Pharmacopoeia 3.1.1.2, USP Class VI, and REACH requirements. Completely non-cytotoxic, non-hemolytic, and non-pyrogenic. Sterilization by steam in autoclaves, ethylene oxide, or radiation (up to 2.5 Mrad). Full hose roll length is 15 m. Medical hoses of different hardness are available, e.g., TYGON® ND100-80 (hardness 80° Shore (A)). The specified working pressure is defined relative to the burst pressure with a safety factor of 1:5. Material: PVC (special, DEHP-free). Maximum operating temperature: +74°C. Brittleness temperature: -42°C. Hardness: 65° Shore (A). Density: 1.19 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and discharge hose, intended for the transfer of wine, beer, fruit juices, alcohols with a concentration of up to 96%, and other food substances that do not contain fats. The inner layer is odorless and tasteless. It does not contain phthalates and bisphenol A, as well as polycyclic aromatic hydrocarbons (PAH Free), in accordance with ZEK 01.4-08 Cat.1. Tested for heavy metals. Thanks to the external corrugation, the hose is exceptionally flexible and elastic. The outer surface of the hose made of thermoplastic material with slippery fabric properties has a very low coefficient of friction, which further facilitates hose handling and eliminates friction with other hoses and equipment components. The recommended method of installation with fittings is special EASY SHELL clamp shells, shaped to fit the hose corrugation. Standards and requirements: Food industry, food contact 1935/2004/EC and 2023/2006/EC (GMP). Inner layer compliant with FDA 21 CFR 177.2600, BfR XXI cat. 2, D.M. 21/03/73. Inner layer: white, smooth butyl rubber (IIR). Reinforcement: synthetic cord, steel spiral. Outer layer: red synthetic rubber with a thermoplastic coating. Working pressure: 10 bar. Vacuum: 0.6 bar. Operating temperature: from -40°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose designed for the conveyance of air, dust, powders, wood shavings, fine chips, light bulk materials, etc. Suitable for all types of industries, particularly frequently used for dust extraction and the removal of fine solid particles in the woodworking, furniture, ceramics, and plastics industries. Flexible and elastic, even at low temperatures. Compressible, smoother inside compared to ECO 0.4 hose. Good abrasion resistance, also resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. The hose is marked with an arrow indicating the correct direction of medium flow. Wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. The hose is available in the following versions: ECO – standard version, ECO SE – flame-retardant material version (without fire classification), ECO AS – permanently antistatic version ISO 8031: R <109 Ω, TRGS 727 (6.4.2.4): R <2.5 x 108 Ωm, directive 2014/34/EU (ATEX): can be used in specific explosion hazard zones after risk analysis, ECO SE AS – antistatic and flame-retardant version (available on special request). The ECO hose is produced in a manufacturing process compliant with sustainable development policies, using raw materials from recycled clean production waste, renewable energy, closed water cycles, and other innovations. Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Wall thickness measured between the spiral: 0.6 mm. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSpecialized suction and discharge hose for water and sewage in sanitary installations on ships, motorboats, yachts, etc. Odorless hose that does not allow odors from sewage discharge to escape outside (5-year warranty). The outer layer is resistant to marine factors and weather conditions. It has resistance to vacuum. Compliant with EN ISO 8099 standard. A special version SANITARY STAR / 7 with a working pressure of 7 bar is available upon special order. Standard length: 60 m or 120 m. Inner layer: white synthetic rubber. Reinforcement: synthetic braid, steel spiral. Outer layer: white synthetic rubber. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and discharge hose for the transfer of almost all aggressive chemical substances. Specifically designed for the petrochemical industry for fuels with high concentrations of aromatic hydrocarbons, hot oil, and solvents. Due to the high overall chemical resistance of FKM rubber, it can be used for aggressive chemicals, in many cases also at elevated temperatures. Used for the transshipment of chemicals from road and rail tankers. Inner layer made of smooth black FKM fluorine rubber. Reinforcement with synthetic cord and steel spiral. Outer layer made of CR chloroprene rubber, antistatic, resistant to weather conditions, ozone, abrasion, and oils. Two built-in copper wires for discharging electrostatic charges. Compliant with EN 12115:11 (type M). Confirmation of resistance and application conditions requires contact with Tubes International, especially for temperatures above 50°C. Vacuum: 0.9 bar. Inner layer: black FKM rubber (FPM, viton). Reinforcement: synthetic cord, steel spiral. Outer layer: black CR rubber. Working pressure: 16 bar. Operating temperature: from -25°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, thick, flexible hose designed for suction and transport of powders, grains, light granules, and other bulk materials in the food and pharmaceutical industries. Used, among others, for powdered milk, grains, rice, coffee, tea, flour (PAS version). Quite flexible, low compressibility, smooth inside, elastic even at low temperatures. Resistant to abrasion, resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. Versions: P7 M PU FOOD – standard, steel wire spiral; P7 M PU PAS FOOD – stainless steel spiral, hose material permanently antistatic (R ≤108 Ω, according to TRGS 727). P7 M PU FOOD and P7 M PU PAS FOOD hoses comply with European requirements 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 and 178.2010. Suitable for temporary contact with food during the transport of dry, bulk, non-fatty surface food substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International). Hose material: transparent polyether-polyurethane. Wall thickness measured between the spiral: 1.4 mm. Reinforcement: steel wire spiral (P7 M PU FOOD), stainless steel wire spiral AISI 301 (P7 M PU PAS FOOD). Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
