Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsCream-beige flexible hose reinforced with polyester braid, odorless and tasteless, non-toxic. Resistant to temperature over a wide range from -60°C to +135°C. Flexible and elastic, resistant to deformation and abrasion. Used for pressure transfer, dispensing, and portioning of cold and hot food products, for soaps, detergents, and disinfectants, for paints and toners, pesticides, and fertilizers. The hose is an alternative to commonly used PVC or silicone hoses. It has good chemical resistance to a range of chemicals, particularly acids and bases, oxidizing agents such as hydrogen peroxide, sodium hypochlorite, or ozone. Resistant to a variety of animal and vegetable fats. Not recommended for hydrocarbons. Resistant to aging and UV radiation. Meets hygiene requirements and food contact standards - US FDA 21 CFR 177.2600, NSF-51, and 3-A. Multiple sterilization possible with steam in autoclaves, CIP and SIP cleaning of installations, ethylene oxide, or radiation methods. Full hose roll length: 15 m. Working pressure defined relative to burst pressure with a safety factor of 1:4. Material: norprene® - thermoplastic elastomer (TPE). Maximum operating temperature: up to +135°C. Brittleness temperature: -60°C. Hardness: 61° Shore (A). Density: 0.98 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality suction and discharge hose designed for the transfer of a wide range of aggressive chemical substances. The hose's broad application, primarily in the chemical industry, is conditioned by the excellent resistance of fluoropolymer FEP to aggressive solvents and concentrated alkalis and acids such as hydrochloric, sulfuric, phosphoric, nitric acids, as well as sodium and potassium hydroxides. The hose can also be used in the food and pharmaceutical industries. It is commonly used in cleanroom environments. The inner layer is made of white tetrafluoroethylene/fluoropropylene copolymer FEP (a thermoplastic fluoropolymer with properties similar to Teflon), mirror-smooth (prevents medium deposition on the walls and is easy to maintain cleanliness), odorless and tasteless, meeting high hygiene standards (FDA, USP Class VI). Intermediate layers made of white synthetic rubber include reinforcement with synthetic cord, a steel wire spiral, and two copper wires for discharging electrostatic charges. The outer layer is made of orange EPDM rubber, resistant to abrasion, ozone, and weather conditions. The hose features excellent chemical resistance and cleanliness of FEP, as well as exceptional temperature resistance. Specifically designed for Cleaning-in-Place (CIP) cleaning methods, including steam sterilization at 150ºC. Standards and requirements: Chemical hoses: EN 12115:2011 (type M). Food industry, contact with food (inner layer): USP Class VI, FDA 21 CFR 177.1550. Confirmation of resistance and application conditions requires contact with Tubes International. Inner layer: white, smooth FEP. Reinforcement: synthetic cord, steel spiral. Outer layer: orange smooth EPDM rubber. Working pressure: 16 bar. Vacuum: 0.9 bar. Operating temperature: from -40°C to +150°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible hose with a thick wall, designed for the discharge of chips, bulk materials, granules, etc. Suitable for all types of industry, particularly commonly used for discharging chips and other solid particles in the wood, furniture, ceramics, and plastics industries. The thick wall and dense reinforcing spiral ensure high pressure parameters. Very smooth on the inside, low compressibility, and flexible - even at low temperatures. Excellent abrasion resistance, also resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. The hose is marked with an arrow indicating the correct direction of medium flow. The wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. The hose is available in the following versions: ECO – standard version, ECO SE – version made of flame-retardant material (UL94 V-2), ECO AS – permanently antistatic version (ISO 8031: R <109 Ω, TRGS 727 (6.4.2.4): R <2.5 x 108 Ωm, directive 2014/34/EU (ATEX): can be used in specific explosion hazard zones after risk analysis), ECO SE AS – antistatic and flame-retardant version (available on special request). The ECO hose is produced in a manufacturing process compliant with sustainable development policies, using raw materials from recycled clean production waste, renewable energy, closed water circulation, and other innovations. Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Wall thickness measured between the spiral: 1.4 mm. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction and discharge hose designed for the transfer of liquid chemicals, including aggressive acids, bases, alcohols, and other detergents used for cleaning installations in food processing plants (selection according to the principles in the "Chemical Hoses" section of this catalog). The inner layer made of UPE complies with FDA requirements for food contact. Widely used in the food, cosmetic, chemical, and petrochemical industries. It features a copper wire ensuring electrical continuity between the hose ends. The outer layer is resistant to abrasion, ozone, and weather conditions. Compliant with EN 12115:11 requirements (type M, resistance between hose ends R ≤ 100 Ω, guaranteed for hoses up to 40 m in length). Standards and requirements: 1) Chemical hoses EN 12115:2011. Food industry, food contact (inner layer) 1935/2004/EC, 2023/2006/EC (GMP), 10/2011/EU (simulant fluids A, B, D2), FDA 21 CFR 177.1520, BfR III. Installation: use smooth fittings with a spigot ("tail" to the hose) without sharp or high ribs that could cut or damage the inner UPE layer when tightened. The spigot diameter should be precisely matched to the hose diameter to ensure tightness. Installation with clamp sleeves or shell clamps. Inner layer: white polyethylene UPE. Reinforcement: synthetic cord, steel spiral. Outer layer: blue EPDM rubber. Working pressure: 16 bar. Vacuum: 0.8 ÷ 0.9 bar - depending on the hose diameter. Operating temperature: -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, glassy transparent, flexible hose free of odor and taste, non-toxic, phthalate-free and BPA (Bisphenol A) free. Designed for the transfer and dispensing of food products, particularly dairy products, spices, vitamin concentrates, flavors, etc. The smooth, non-porous inner surface of the hose eliminates the problem of product particle settling and bacterial growth. Resistant to alkaline cleaning agents. Can be used with peristaltic pumps (moderate lifespan). Meets hygiene and food contact requirements: European 1935/2004/EC and 10/2011 EU (for conditions and substances according to certification), American FDA, NSF-51, NSF-61, 3-A, Japanese #370/1959 and MHLW370(3-D). Sterilization by steam or ethylene oxide is possible. Compliant with REACH and California Proposition 65 – does not contain hazardous and prohibited substances. Full roll length of the hose is 15 m (from an inner diameter of 50.8 mm - 6 m). Working pressure specified relative to burst pressure with a safety factor of 1:5. Material: PVC (special). Maximum operating temperature: +74°C. Brittleness temperature: -36°C. Hardness: 66° Shore (A). Density: 1.21 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight and very flexible suction and discharge hose, designed for general industrial applications (in industry, construction, agriculture). It can be used for water, light chemicals, sludges and wastewater, plant protection products, other liquids (without fats, oils, and hydrocarbons) as well as for air, vacuum transport of dust, powders, granules, and other lightly abrasive bulk materials (non-greasy). Abrasiveness and potential static electricity issues should be considered. Reinforced with a hard PVC spiral, impact-resistant, providing good vacuum resistance and preventing hose collapse. The smooth inner surface reduces flow losses and ensures ease of cleaning. The outer surface is slightly corrugated, with smooth surfaces for small diameters. As a hose reinforced only with a hard PVC spiral, lacking a braid, it exhibits some elongation under pressure, which should be taken into account in applications, especially at elevated temperatures. Hose material: green transparent PVC. Reinforcement: hard PVC spiral. Working pressure at 20°C: from 2 bar to 6.5 bar - depending on the hose diameter. As the operating temperature increases, the working pressure value of the hose decreases. Operating temperature: from -25°C to +55°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong, thick, flexible hose designed for suction and transport of abrasive bulk materials, granulates, roofing gravel, industrial cleaning, abrasive for sandblasting, silos, bulk material tankers, etc. Compliant with DIN 26057 Type 4 (SMARTFLEX® 2.0). Antistatic and flame-retardant, ensuring high workplace safety. Thick wall and dense, robust reinforcing spiral provide high resistance to vacuum. Smooth inside, non-compressible, not very flexible but elastic, even at low temperatures. Very good abrasion resistance, also resistant to microbes and hydrolysis. Free from halogen compounds and plasticizers. Resistant to oils and gasoline. The optimal flow direction of the medium is marked with an arrow. The wall thickness of the hose is measured between the spiral. Other diameters may be available upon special request. Antistatic properties: permanently antistatic (according to ISO 8031 resistance R <109 Ω, according to German technical regulations TRGS 727 (6.4.2.4) specific resistance R < 2.5 x 108 Ωm, according to directive 2014/34/EU (ATEX) can be used in specific explosion hazard zones - which must be preceded by a risk analysis). After effective grounding of the spiral on both sides, it can be treated as electrically conductive – in accordance with BGI 739-2 recommendations. Flame-retardant – according to DIN 4102 class B1. Wall thickness measured between the spiral: 2.0 mm (SMARTFLEX® 2.0), 2.5 mm (SMARTFLEX® 2.5). Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible suction and discharge hose intended for the transport of food, pharmaceutical, and cosmetic substances: water, fruit juices, beer, wine, vinegar, alcohols up to 96% concentration, milk and its derivatives, creams, soaps, aromatic substances, pigments, and others. Resistant to fats and oils in standard usage conditions. It has good chemical resistance to light chemicals – solutions of acids and bases. Extruded, completely smooth inner and outer surface of the hose facilitates flow and cleaning. Reinforced with a spiral of stainless steel wire embedded in a TPE-S wall, making it resistant to vacuum and collapsing. The transparent wall allows for easy visual monitoring of flow. The hose material is non-vulcanized, clean (without vulcanization additives), resistant to hydrolysis, does not promote bacterial growth, has low porosity and low permeability. Completely neutral in taste and odor, does not alter the organoleptic properties of the medium. Resistant to aging, weather conditions, and UV radiation. Cleaning by SIP method is not recommended, as it significantly shortens the service life. Use for high-proof alcohol (its vapors or other flammable substances) requires consideration of hazards related to static electricity. As a hose reinforced only with a spiral (without a braid), it exhibits some elongation under pressure, therefore the maximum working pressure of the hose is low (safety factor 1:5). Hose cleaning, disinfection, or sterilization should be carried out strictly according to the recommendations provided in the catalog sheet below. Standards and requirements: 1) Food industry, contact with food: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulation fluids A, B, C, D1, D2), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 “e”. 2) Pharmaceutical industry USP CLASS VI. Hose material: transparent TPE-S. Reinforcement: AISI 302 steel spiral. Working pressure: from 1 bar to 1.5 bar, depending on the hose diameter. Operating temperature: -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong, thick, flexible hose designed for suction and transport of abrasive bulk materials: granules, grains, sand, gravel. Thick wall and very dense reinforcing spiral ensure high resistance to pressure and vacuum. Very smooth inside, non-compressible, not very flexible (r=4xD), retains its elasticity even at low temperatures. Hose with good abrasion resistance, also resistant to oils and gasoline. Installation on couplings with bridge clamps (right-handed) or special installation on industrial ends, e.g., flanges. Other diameters may be available upon special request. Versions: P3 S PU – standard version, made of polyester-polyurethane, very abrasion-resistant, and P3 S PU AE - version made of polyether-polyurethane, with good abrasion resistance, resistant to microbes and hydrolysis; approved for contact with food substances, compliant with European regulations 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP), and American FDA 21 CFR 177.2600 and 178.2010. Suitable for temporary contact with food during the transport of dry, bulk, non-fatty food substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International); P3 S PU AS – antistatic version (R ≤108 Ω), compliant with TRBS 2153 and for suction also with TRGS 727, made of polyether-polyurethane, with good abrasion resistance, resistant to microbes and hydrolysis. Hose material: transparent polyester-polyurethane (P3 S PU), transparent polyether-polyurethane (P3 S PU AE and P3 S PU AS). Wall thickness measured between the spiral: 2 mm. Reinforcement: dense spiral made of steel wire. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and discharge hose intended for the transfer of pharmaceutical products, cosmetics, food substances, and chemicals (selection according to the principles in the chapter "Chemical Hoses"). It does not contain plasticizers, phthalates, or animal-derived substances. It is characterized by high thermal and mechanical strength. It is an excellent solution for processing industries requiring the highest safety during the transfer of high-purity products. The outer layer is resistant to abrasion, ozone, and weather conditions. It has two copper wires ensuring electrical continuity between the hose ends. Standards and requirements: 1) General EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) Food industry, contact with food 1935/2004/EC and 2023/2006/EU (GMP). The inner layer complies with 10/2011/EC, D.M. 21/03/73, FDA 21 CFR 177.1550. The outer layer complies with FDA 21 CFR 177.2600, D.M. 21/03/73. 3) Pharmaceutical industry USP Class VI (inner layer). Installation: use smooth fittings with a spigot ("tail" to the hose) that do not have sharp or high ribs that could cut or damage the inner layer made of MFA when tightened. The diameter of the spigot should be precisely matched to the diameter of the hose to ensure tightness. Installation with clamp sleeves or shell clamps. Inner layer: smooth fluoropolymer MFA. Reinforcement: synthetic cord, steel spiral. Outer layer: smooth EPDM rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: -50°C to +170°C (for most chemicals).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, strong suction and discharge hose designed for water and sewage. Externally corrugated, internally almost smooth. Good resistance to external damage and harsher operating conditions. Maintains high flexibility at low temperatures. Used in irrigation systems, industrial water installations, for emptying septic tanks, etc. A special version, ARIZONA EXTREME ELASTIC, is also available on special order, flexible at very low temperatures (down to -40°C). Hose material: gray and green PVC. Reinforcement: hard PVC spiral. Working pressure: from 1.5 bar to 7 bar - depending on the hose diameter and temperature. Operating temperature: from -25°C to +55°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible and bendable, temperature-resistant two-layer suction and discharge hose designed for the removal and transfer of vapors, fumes, and high-temperature air. Flame-retardant, chemically resistant, with fairly good resistance to hot sparks. Used in the construction of furnaces (metal and glass foundries, ceramic and chemical industries), vehicles (exhaust gas discharge systems, engine testing stations, etc.), aerospace and military applications. Characterized by high compressibility - up to 1:6, strong construction, and impact resistance due to the external spiral. Also available with a stainless steel spiral (from a diameter of 80 mm). Hose installation on couplings with bridge clamps (left-handed). Standard length: from 2 to 10 m - contact Tubes International. Hose material: 2 layers of glass fabric, with the outer layer coated in silicone (gray). Reinforcement: external spiral made of galvanized steel wire and sheet. Operating temperature: from -50°C to +450°C (temporarily up to +500°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, transparent, flexible fuel hose with exceptionally low fuel vapor permeability through the hose wall. Meets American EPA and CARB requirements (permeability up to 15 g/m2/24h). Patented multi-layer hose construction with an inner layer of PVDF fluoropolymer resistant to fuels containing up to 100% ethanol. Resistant to swelling and hardening due to hydrocarbons, significantly reduces the risk of cracking and leakage. Minimal extractability ensures fuel purity, and the exceptionally low aromatic substance permeability protects the operator and the environment. Ozone and UV radiation resistant (ANSI B175.1 D). The flexibility of the hose facilitates installation even in tight spaces and is maintained at low temperatures, ensuring hassle-free fuel withdrawal in any position. The transparent wall allows for flow monitoring. Thanks to the inner layer of PVDF, the hose is resistant to most chemicals and fuels. It can be submerged in fuel (only not recommended for repeated use at high external temperatures). Flame retardant (UL 94 HB). Used in modern lawn mowers, chainsaws, gas drills, hedge trimmers, and other gardening machines. Full hose roll length is 15 m. Working pressure defined relative to burst pressure with a safety factor of 1:5. Material: PVDF / TPE (multi-layer). Operating temperature: from -40°C to +82°C. Brittleness temperature: -90°C. Hardness: 78° Shore (A). Density: 1.27 g/cm³. Note: Product packaged in the Clean Zone of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, glassy transparent, flexible hose free of phthalates and BPA (Bisphenol A). Designed for the transfer and dispensing of food products, particularly juices, beverages, and bottled water. Does not alter the taste and smell of products, and its non-wetting properties allow for complete drainage and easy cleaning by rinsing. Can be used with peristaltic pumps, but the lifespan is moderate. Meets hygiene and food contact requirements: European 1935/2004/EC and 10/2011 EU (for conditions and substances according to certification), American FDA, NSF-51, NSF61, 3-A, Japanese #370/1959 and MHLW370(3-D). Sterilization by steam or ethylene oxide is possible. Compliant with REACH and California Proposition 65 – does not contain hazardous and prohibited substances. Full hose roll length is 15 m (from internal diameter 50.8 mm - 6 m). The specified working pressure is relative to the burst pressure with a safety factor of 1:5. Material: PVC (special). Maximum operating temperature: +74°C. Brittleness temperature: -36°C. Hardness: 66° Shore (A). Density: 1.21 g/cm³. Note: Product packaged in the Clean Zone of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose designed for the discharge of hot exhaust gases from gasoline and diesel engines. Used as a workshop hose deployed on the floor, adapted for drum winding systems, as a suction duct, or at engine testing stations. Resistant to crushing due to reinforcement with a thick, white, round nylon spiral (PA), covered externally with black TPE. Chemically resistant, particularly to gasoline and oil vapors, as well as ozone, hydrolysis, microbes, and UV radiation. Halogen-free and free of plasticizers. The P-G-EX 1 hose should be used with a vacuum exhaust gas removal system, employing the appropriate coupling between the hose and the engine exhaust outlet. Other diameters ranging from 40 to 250 mm are available on special order. Hose installation on couplings with bridge clamps (right-handed). Standard lengths: 2.5 m, 5 m, 7.5 m, 10 m, 15 m, and 20 m. Hose thickness measured between the spiral: 0.4 mm. Hose material: polyester fabric impregnated with a black TPE coating (thermoplastic elastomer). Reinforcement: nylon spiral in a TPE protective cover against abrasion. Operating temperature: from -40°C to +150°C (temporarily +170°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction and discharge hose with thick walls, designed for the transfer of food substances requiring the use of odorless and tasteless rubber. It contains no phthalates or bisphenol A. The hose is specially designed for the transfer of oils and fats. Widely used in the oil and fat industry. The outer layer is resistant to grease and aging. Standards and requirements: Food industry, food contact 1935/2004/EC and 2023/2006/EC (GMP). The inner layer complies with FDA 21 CFR 177.2600, D.M. 21/03/73. Inner layer: white NBR/PVC rubber. Reinforcement: two layers of synthetic cord, steel spiral. Outer layer: blue smooth CR rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: -15°C to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVacuum-resistant suction and discharge hose designed for cooling water in foundries, smelters, and all applications where rubber hoses operate close to a heat source. Glass fiber covering resistant to temperatures up to +530°C caused by thermal radiation. Used in cooling systems. Particularly recommended for water installations near metallurgical furnaces. Resistant to short-term exposure to splashes of molten hot metal. Standard length: 60 m or 120 m. Inner layer: black SBR rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: EPDM rubber / glass fiber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: from -40°C to +70°C, external up to +530°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, very flexible and elastic, resistant to creasing and twisting hose designed for the removal of dust, contaminated air, and welding fumes. Commonly used in industrial vacuum systems. The external reinforcing spiral shaped in the profile of the hose, left-handed, allows for the attachment of appropriate fittings for vacuums with left-handed threads (plastic fittings with index ME-EVA...). Hose installation is also possible using clamps on appropriate ends, pipe fittings, etc. Hose material: gray ethylene-vinyl acetate (EVA). Reinforcement: reinforcing spiral shaped in the profile of the hose. Operating temperature: from -30°C to +60°C for EVA hose and from -25°C to +60°C for EVA IVH hose (operating vacuum dependent on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible suction and discharge hose intended for the transport of food, pharmaceutical, and cosmetic substances: water, fruit juices, beer, wine, vinegar, alcohols up to 96% concentration, milk and its derivatives, creams, soaps, aromatic substances, pigments, and others. Resistant to fats and oils within standard usage range. Good chemical resistance to light chemicals – solutions of acids and bases. Extruded, completely smooth inner and outer surface of the hose facilitates flow and cleaning. Double reinforcement of the hose with a spiral and braid ensures good strength against overpressure and vacuum. The hose material is non-vulcanized, clean (contains no vulcanization additives), resistant to hydrolysis, does not promote bacterial growth, has low porosity and low permeability. Completely neutral in taste and odor, does not alter the organoleptic properties of the medium. Resistant to aging, weather conditions, and UV radiation. Hose cleaning, disinfection, or sterilization must be carried out strictly according to the recommendations provided in the catalog sheet below. Washing by SIP method is not recommended as it shortens the hose's service life. Application for high-proof alcohol (its vapors or other flammable substances) requires consideration of hazards related to static electricity. Norms and requirements: 1) Food industry, contact with food: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulation fluids A, B, C, D1, D2), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 “e”. 2) Pharmaceutical industry: USP CLASS VI. Hose material: transparent TPE-S. Reinforcement: polyester braid, AISI 302 steel spiral. Working pressure: from 7 bar to 17 bar, depending on the hose diameter. Operating temperature: -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight, flexible hose designed for the transport of air, vapors, dust, fine particles, powders, grains, and lightweight bulk materials. Intended for use in the food and pharmaceutical industries. Highly flexible and very compressible axially, also elastic at low temperatures. Good abrasion resistance, resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. The hose is available in the following versions: P2 PU FOOD – steel wire (copper-plated) spiral; P2 PU PAS FOOD – stainless steel wire spiral, hose material permanently antistatic (R ≤ 108 Ω, according to TRGS 727). P2 PU FOOD and P2 PU PAS FOOD hoses comply with European regulations 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP), and American FDA 21 CFR 177.2600 and 178.2010. Suitable for temporary contact with food during the transfer of dry, bulk, non-fatty food substances - under the conditions specified in the manufacturer's declaration of conformity (available from Tubes International). Hose material: transparent polyether-polyurethane. Wall thickness measured between the spiral: 0.4 mm. Reinforcement: steel wire spiral (P2 PU FOOD), stainless steel wire AISI 301 spiral (P2 PU PAS FOOD). Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible suction and discharge hose intended for water, juices, beverages, and other food products. The absence of phthalates in the material allows the hose to be used for the transfer of milk and its derivatives, as well as alcohols with a concentration of up to 50% and temperatures up to +60°C. Not recommended for oils and fatty food substances. Reinforcement with a hard PVC spiral, resistant to impacts, ensures good resistance to vacuum and hose collapse. The transparent wall allows for easy visual monitoring of flow. The smooth inner surface reduces flow losses and ensures ease of cleaning. The outer surface of the hose is also smooth, facilitating the installation of fittings using tapes or clamps, reducing external damage from abrasion, and making it easier to keep the hose clean. In applications not involving direct contact with food (in industry, construction, agriculture), it can be used for light chemicals, water, sludges, and wastewater, other liquids (without fats, oils, and hydrocarbons), as well as for air, vacuum transfer of dust, powders, granules, and other lightly abrasive bulk substances (non-fatty). Abrasiveness and potential static electricity issues should be considered. As a hose reinforced only with a hard PVC spiral, lacking a braid, it exhibits some elongation under pressure, which should be taken into account in applications, especially at temperatures above +40°C. Standards and requirements: Food industry, contact with food: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B, C, and D1), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: hardened PVC spiral. Working pressure: from 3 bar to 7 bar, depending on the hose diameter. Operating temperature: -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsExternally corrugated flexible and strong suction and discharge hose for water and sewage. It is characterized by good resistance to external damage and harsh operating conditions, as well as resistance to UV radiation and low temperatures. Used in irrigation systems, tankers, for flushing sewers, and emptying septic tanks. Also used in industrial installations. Hose material: gray-purple PVC. Reinforcement: hard PVC spiral. Working pressure: from 3 bar to 8 bar, depending on the hose diameter and temperature. Operating temperature: from -20°C to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible, and pliable suction hose resistant to temperature, designed for the discharge of gases, vapors, smoke, and high-temperature air. Flame-retardant, resistant to hot sparks within a certain range. Mainly used in the metallurgical, foundry, ceramic, and glass industries, around furnaces, engines, and as thermal insulation. Characterized by high compressibility - up to 1:6, strong construction due to glass fabric reinforced with stainless steel threads, and impact resistance thanks to the external spiral. Used exclusively as a suction hose operating under vacuum, due to the possibility of gas permeation when under pressure (degassing). Also available with a stainless steel spiral (from a diameter of 80 mm). Hose installation on couplings with left-handed bridge clamps. Standard length: from 2 to 10 m - contact Tubes International. Hose material: impregnated glass fabric with stainless steel fibers, externally gray. Reinforcement: external spiral made of wire and galvanized steel sheet. Operating temperature: from -50°C to +400°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight and flexible suction and discharge hose, intended for general industrial applications (in industry, construction, agriculture). It can be used for water, light chemicals, sludges and wastewater, plant protection products, other liquids (excluding fats, oils, and hydrocarbons) as well as for air, vacuum transfer of dust, powders, granules, and other lightly abrasive bulk materials (non-greasy). Abrasiveness and potential static electricity issues should be considered. In the food industry, it can be used for the transfer of hydrated food, acidic substances, and alcohols up to 20%, e.g., juices, beverages, beer, wine (simulants A, B, C; up to +60°C and 2 hours). Not recommended for milk and its derivatives, as well as oils and fatty food substances. Reinforced with a hard PVC spiral, resistant to impact, ensures good vacuum resistance and prevents hose collapse. The smooth inner surface reduces flow losses and ensures ease of cleaning. The outer surface is slightly corrugated, smooth for small diameters. The FLORIDA hose complies with European requirements 1978/142/EEC, 1935/2004/EC, 1895/2005/EC, and 10/2011/EU (simulants A, B, C), 2023/2006/EC (GMP). Suitable for temporary contact with food during the transfer of food substances - under the conditions specified in the manufacturer's declaration of conformity (available from Tubes International). Hose material: transparent PVC. Reinforcement: hard PVC spiral (gray). Working pressure for a temperature of 20°C: from 3 bar to 6.5 bar - depending on the hose diameter. As the operating temperature increases, the working pressure value of the hose decreases. Operating temperature: from -5°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, lightweight, and strong suction-discharge hose designed for the transport of water, sewage, sludge, non-corrosive liquids, and natural fertilizers (manure). The inner layer is made of smooth synthetic rubber, resistant to sludge and sewage. The corrugated outer layer provides a small bending radius and is resistant to ozone, weather conditions, and aging. Intended for agricultural, construction, and industrial applications, used for emptying septic tanks, as a suction hose for water and sewage pumps, for drainage and irrigation, and for tankers. Can be used for air extraction, dust, and bulk materials. Installation – depending on the diameter and type of fittings using steel bands, clamps, brackets, or compression sleeves. Inner layer: black synthetic rubber (SBR). Reinforcement: synthetic cord, steel spiral. Outer layer: black corrugated synthetic rubber. Working pressure: 3 bar. Operating temperature: from -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, very flexible and elastic hose designed for the extraction of hot vapors, smoke, gases, blowing, and the discharge of cooling air. Chemically resistant, UV resistant, and aging resistant. Used, among others, for gas extraction in the metallurgical industry, foundries, glass and ceramic industries, for hot air in industrial dryers, in printing houses and paper mills, in vehicles and engines for cooling air, incinerators, as well as for the extraction of exhaust gases and welding gases. Smooth inside (when straightened), with a very small bending radius allowing easy installation in tight spaces of equipment and vehicles. Not recommended for continuous dynamic bending. Installation with clamps. Other diameters and lengths, soft ends of sections, etc., available on special order. Hose material: glass fabric impregnated with red silicone. Reinforcement: internal spiral of steel wire, external strand of fiberglass. Operating temperature: from -70°C to +250°C (temporarily up to +300°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, thick, flexible hose designed for suction and transport of granules and other bulk materials. Intended for use in various types of industry. Used for plastic granules, insulation materials, waste, sand, and other construction materials. Quite flexible, low compressibility, smooth inside, elastic even at low temperatures. Good abrasion resistance, resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. Installation on couplings with bridge clamps (right-handed). Other diameters may be available. In addition to the standard version P7 M PU AE, the hose is available in the P7 M PU EL version, which is electrically conductive (R ≤104 Ω), compliant with ATEX 2014/34/EU, TRBS 2153, and for suction also with TRGS 727, it can be used in explosion hazard zones after conducting a risk assessment. Hose material: polyester-polyurethane. Wall thickness measured between the spiral: 1.4 mm. Reinforcement: spiral with steel wire. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong and thick, flexible hose designed for suction and transport of abrasive bulk materials, granules, sand, gravel, pebbles, agricultural substrate. Used for loading and unloading silos, vehicles, and suction excavators, transloading from tankers, etc. Thick wall and fairly dense reinforcing spiral provide high resistance to pressure and vacuum. Smooth inside, non-compressible, quite flexible (r=2.5xD), elastic even at low temperatures. Hose with good abrasion resistance, also resistant to oils and gasoline. Installation on couplings with bridge clamps (right-handed) or special installation on industrial ends, e.g., flanges. Other diameters may be available upon special request. Versions: P3 SV PU – with polyester – polyurethane, very abrasion resistant; P3 SV PU AE - version with polyether – polyurethane, abrasion resistant, resistant to microbes and hydrolysis, compliant with European regulations 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 and 178.2010. Suitable for temporary contact with food during the transfer of dry, bulk, non-fatty substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International). Hose material: transparent polyester-polyurethane (P3 SV PU), polyether – polyurethane (P3 SV PU AE). Wall thickness measured between the spiral: 2.5 mm. Reinforcement: spiral made of steel wire. Operating temperature: from -40°C to +100°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible suction hose designed for sewage and water. Corrugated on the outside, nearly smooth on the inside. The special profile makes the hose resistant to vacuum and kinking (it returns to its shape). As a polyethylene hose, it has very good chemical resistance and resistance to biological corrosion (rotting, decay). It remains flexible at low temperatures. The hose is commonly used for emptying septic tanks and portable toilets, in construction, tourist facilities, marinas, and airports. Hose material: yellow polyethylene profile (PE). Reinforcement: black polyethylene profile (PE). Vacuum: 0.95 bar (for diameter 51mm ÷ 76mm); 0.85 bar (for diameter 102mm). Operating temperature: from -40°C to +60°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction and discharge hose designed for fatty and non-fatty food substances, requiring the use of odorless and tasteless rubber. It contains no plasticizers, phthalates, or animal-derived substances. Particularly recommended for handling and heavy working conditions. Widely used in the food industry in dairies and oil mills. The inner layer made of NBR is resistant to commonly used cleaning agents and processes in the food industry. The outer layer is resistant to temporary contact with animal and vegetable fats, abrasion, and weather conditions. Standards and requirements: 1) General: EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) Food industry, food contact: EC 1935/2004, EC 2023/2006 (GMP). The inner layer complies with D.M. 21/03/73, FDA 21 CFR 177.2600, BfR, 3A Sanitary Standards. RAL (German Institute for Quality Assurance and Certification). Vacuum: 0.9 bar. Inner layer: white NBR rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: blue CR rubber. Working pressure: 10 bar. Operating temperature: from -20°C to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, exceptionally flexible and compressible hose designed for air conditioning, air exhaust and blowing, and welding fume extraction. Widely used for extraction arms, ventilation, tent heating, and drying of construction structures. Self-extinguishing and non-flammable (flame-retardant) according to UL94 V-0. Resistant to hydrolysis and microbes. Other diameters ranging from 30 to 800 mm and colors: black, blue, white, and yellow are available upon special order. Hose installation on couplings with bridge clamps (right-handed). Hose material: polyester fabric impregnated with gray PVC. Wall thickness: 0.4 mm. Reinforcement: steel wire spiral. Operating temperature: from -30°C to +80°C (temporarily up to +100°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, very flexible and elastic hose designed for the extraction of hot vapors, smoke, gases, blowing, and the discharge of cooling air. Reinforced version of the NEOPRENE 1 hose, with two layers of fabric impregnated with neoprene and a steel spiral placed between the layers. Chemically resistant, UV resistant, and aging resistant. Used, among others, for hot air in granulate dryers and film blowers in plastic processing, in paint dryers in printing houses, other industrial dryers, in the electronics industry, in vehicles and engines for cooling air, incinerators, as well as for the extraction of exhaust gases and welding gases. Smooth inside (in a straightened state), with a small bending radius allowing easy installation in tight spaces of equipment and vehicles. Installation with clamps. Other diameters and lengths, soft ends of sections, etc., available on special order. Hose material: two glass fabrics impregnated with black CR rubber (Neoprene® - chloroprene rubber). Reinforcement: steel wire spiral, with two fiberglass cords on the outside. Operating temperature: from -35°C to +135°C (temporarily up to +150°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight, flexible, wrinkle-resistant hose designed for the transport of air, smoke, fiber dust, dirt, and other lightweight substances. Used in industrial vacuum cleaners. Made of conductive polyethylene (PE) and elastomer, with low material resistance, excellent for applications where the accumulation of electric charges must be avoided (the hose must be effectively grounded). The external reinforcing spiral shaped in the hose profile, left-handed, allows for the attachment of appropriate fittings for vacuum cleaners with left-threaded connections, e.g., plastic fittings for EVA hose: DN32, 38, and 50 or suitable conductive fittings. Hose installation is also possible using clamps on appropriate ends, pipe fittings, etc. The hose with diameters DN38 and DN50 has a declaration of conformity with ATEX requirements and TRGS 727 standards and can be used in explosion hazard zones, provided the hose is effectively grounded and a risk analysis is conducted by the user. Hose material: black special polyethylene (PE) and elastomer. Reinforcement: reinforcing spiral shaped in the hose material. Operating temperature: from -20°C to +60°C (operating vacuum depends on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight, highly flexible and bendable hose designed for the discharge of aggressive chemical vapors and gases, ventilation, and air conditioning. Good chemical resistance to solvents and other aggressive vapors. Chemical resistance verification - chemical resistance table for polyethylene (preliminary selection), confirmation of resistance and application conditions - by Tubes International. Resistant to hydrolysis and biological corrosion. Does not contain halogen compounds and plasticizers. Mainly used in the chemical industry. Available on request in diameters ranging from 40 to 610 mm. The hose is available in two versions: P2PE - standard and P2PE EL - electrically conductive with a resistance of R ≤104 Ω, compliant with the ATEX directive 2014/34/EU and the TRGS 727 standard, made of black polyethylene. Hose material: polyethylene (PE), transparent - standard version P2PE, black - electrically conductive version P2PEEL. Wall thickness: 0.4 mm. Reinforcement: steel wire spiral. Operating temperature: from -40°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible medium-thickness hose designed for the extraction and transport of powders, grains, light granules, and other bulk materials. Intended for use in the food and pharmaceutical industries. Used, among others, for powdered milk, grains, rice, coffee, tea, flour (PAS version). Flexible, fairly compressible, almost smooth inside, elastic even at low temperatures. Good abrasion resistance, resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. The hose is available in the following versions: P7 OL PU FOOD – steel wire (copper-plated) spiral; P7 L PU PAS FOOD – stainless steel spiral, hose material permanently antistatic (R ≤108 Ω, according to TRGS 727). The P7 OL PU FOOD and P7 L PU PAS FOOD hoses comply with European requirements 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP), and American FDA 21 CFR 177.2600 and 178.2010. Suitable for temporary contact with food during the transport of dry, bulk, non-fatty food substances - under the conditions specified in the manufacturer's declaration of conformity (available from Tubes International). Hose material: transparent polyether-polyurethane. Wall thickness measured between the spiral: 0.7 mm. Reinforcement: steel wire spiral (P7 OL PU FOOD), stainless steel AISI 301 wire spiral (P7 L PU PAS FOOD). Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDurable, lightweight, and highly flexible (even at low temperatures) suction and discharge hose designed specifically for the wine industry for heavier working conditions. Stronger than the SPIRABEL® SNTS hose, with a thicker wall. A hose for demanding applications, intended for the transfer of water, beer, quality wines, and spirits with concentrations up to 50% and temperatures up to +40°C, juices, beverages, and other food products. Phthalate-free, allowing it to be used for milk and its derivatives. Not recommended for oils and fatty food substances. Reinforced with a hard PVC spiral, resistant to impacts, provides very good resistance to vacuum and hose collapse. The transparent wall allows for easy visual monitoring of the substance flow. The smooth inner surface reduces flow losses and ensures ease of cleaning. The ease of cleaning is also provided by the smooth outer surface, which is available in hoses up to 63 mm in diameter. In applications not involving direct contact with food (in industry, construction, agriculture), it can be used: 1) for light chemicals, water, sludges, and wastewater, other liquids (without fats, oils, and hydrocarbons); 2) for air, vacuum transfer of dust, powders, granules, and other lightly abrasive bulk substances (non-fatty). Abrasiveness and potential static electricity issues should be considered. As a hose reinforced with a hardened PVC spiral (without a braid), it exhibits some elongation under pressure, which should be taken into account in applications, especially at temperatures above +40°C. Standards and requirements: Food industry, food contact: Compliant with European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B, C, and D1), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: hardened PVC spiral. Working pressure: from 5 bar to 7 bar, depending on the hose diameter. Operating temperature: -25°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight and flexible hose designed for the transport of air, dust, powders, fine wood shavings and chips, very light bulk materials, etc. Suitable for all types of industry, particularly commonly used for dust extraction and the removal of fine solid particles in the woodworking, furniture, ceramics, and plastics industries. Highly flexible and very axially compressible, also elastic at low temperatures. Good abrasion resistance, also resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. The hose is marked with an arrow indicating the correct direction of medium flow. Wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. The hose is available in the following versions: ECO – standard version, ECO SE – version made of flame-retardant material (without fire classification), ECO AS – permanently antistatic version (ISO 8031: R <109 Ω, TRGS 727 (6.4.2.4): R <2.5 x 108 Ωm, directive 2014/34/EU (ATEX): can be used in specific explosion hazard zones after risk analysis), ECO SE AS – antistatic and flame-retardant version (available on special request). The ECO hose is produced in a manufacturing process compliant with sustainable development policies, using raw materials from the recycling of clean production waste, renewable energy, closed water cycles, and other innovations. Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Wall thickness measured between the spiral: 0.4 mm. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and discharge hose for demanding, versatile applications in the food industry. Excellent for the transfer of various types of food products such as: olive oil, wine, beer, fruit juices, milk, fats, and alcohols with a concentration of up to 96%. The inner layer is odorless and tasteless. It does not contain phthalates and bisphenol A, as well as polycyclic aromatic hydrocarbons (PAH Free), in accordance with ZEK 01.4-08 Cat.1. Tested for heavy metals. The outer layer is resistant to weather conditions and ozone. Thanks to the external corrugation, the hose is exceptionally flexible and elastic. The recommended method of installation with fittings is special EASY SHELL clamp shells, shaped to fit the hose's corrugation. Standards and requirements: Food industry, contact with food 1935/2004/EC and EC 2023/2006/EC (GMP). The inner layer complies with FDA 21 CFR 177.2600, BfR XXI cat. 2, D.M. 21/03/73, 3-A Sanitary Standard 18-03 class II. Inner layer: white, smooth synthetic rubber. Reinforcement: synthetic cord, steel spirals. Outer layer: blue synthetic rubber. Working pressure: 10 bar. Vacuum: 0.6 bar. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, single-layer, highly flexible and elastic hose designed for the extraction of hot vapors, smoke, gases, blowing, and the discharge of cooling air. Chemically resistant, UV resistant, and aging resistant. Used, among others, for hot air in granulate dryers and film blowers in plastic processing, in paint dryers in printing houses, other industrial dryers, in the electronics industry, in vehicles and engines for cooling air, incinerators, as well as for the extraction of exhaust gases and welding gases. Smooth inside (when straightened), with a very small bending radius allowing easy installation in tight spaces of equipment and vehicles. Mounted with clamps. Other diameters and lengths, soft ends of sections, etc., available on special order. Hose material: glass fabric impregnated with black CR rubber (Neoprene® - chloroprene rubber). Reinforcement: internal spiral of steel wire, external strand of fiberglass. Operating temperature: from -35°C to +135°C (temporarily up to +150°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDurable, lightweight, and flexible suction and discharge hose designed specifically for the wine industry for heavier working conditions. Stronger than the LUISIANA hose, with a thicker wall. Hose for demanding applications. Intended for the transfer of water, beer, quality wines, and alcohols with a concentration of up to 20%, juices, beverages, and other food products. Free of phthalates. Not recommended for milk and its derivatives, oils, and fatty food substances. Reinforced with a hard PVC spiral, resistant to impact, provides very good resistance to vacuum and hose collapse. The transparent wall allows for easy visual monitoring of flow. The smooth inner surface reduces flow losses and ensures ease of cleaning. In applications not involving direct contact with food (in industry, construction, agriculture), it can be used: 1) for light chemicals, water, sludges, and wastewater, other liquids (without fats, oils, and hydrocarbons); 2) for air, vacuum transfer of dust, powders, granules, and other lightly abrasive bulk materials (non-fatty). Abrasiveness and potential static electricity issues should be considered. Standards and requirements: Food industry, contact with food - compliant with European requirements 1935/2004/EC and 10/2011/EU (simulative fluids A, B, and C), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: hard PVC spiral. Operating temperature: from -5°C to +60°C.
