Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight and flexible hose designed for the transport of air, dust, powders, wood shavings, fine chips, lightweight bulk materials, etc. Specifically designed according to the requirements of the woodworking and furniture industries, it can also be used in other industrial sectors. Antistatic and flame-retardant, it ensures high work safety. Flexible and elastic, even at low temperatures. Less compressible than the SMARTFLEX® 0.4 hose, but smoother on the inside. With very good abrasion resistance, also resistant to microbes and hydrolysis. Free from halogen compounds and plasticizers. Resistant to oils and gasoline. The optimal direction of medium flow is marked with an arrow. The wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. Antistatic properties: permanently antistatic (according to ISO 8031 resistance R <109 Ω, according to German technical regulations TRGS 727 (6.4.2.4) specific resistance R < 2.5 x 108 Ω, according to directive 2014/34/EU (ATEX) can be used in specific explosion hazard zones - which must be preceded by a risk analysis). After effective double grounding of the spiral, it can be treated as electrically conductive – in accordance with the recommendations of BGI 739-2. Flame-retardant – according to DIN 4102 class B1. Hose material: transparent polyester-polyurethane. Wall thickness measured between the spiral: 0.6 mm. Reinforcement: spiral made of steel wire. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality, flexible hose in cream color, specifically designed for the pharmaceutical industry, biotechnology, and laboratories. It has high fatigue resistance, exceptionally long service life in peristaltic pumps, and good resistance to spallation (the chipping of micro-particles from the hose material due to rotor pressure). It also features very low permeability to gaseous media, low absorption levels of transmitted products, and good resistance to acids, bases, and oxidation. Ideal for use in diagnostic processes, sampling and culturing of in vitro cell cultures, vaccine production, bioreactors, sterile filling lines, fermentation processes, extraction, and purification. The opaque wall of the hose protects sensitive products from UV radiation. The hose complies with USP Class VI requirements and is completely non-cytotoxic, non-hemolytic, and non-pyrogenic. Compliant with ISO 10993 for contact with blood, bodily fluids, and tissues for up to 30 days. Meets NSF-51 requirements for food contact. Multiple sterilization by steam in autoclaves is possible (30 min, 1 bar, 121°C), CIP and SIP cleaning of installations, ethylene oxide, or radiation (gamma Cobalt 60 up to 5 Mrad). Flame resistant (UL 94-HB). Full hose roll length is 7.5 m. Working pressure specified relative to burst pressure with a safety factor of 1:5. Material: thermoplastic elastomer (TPE). Operating temperature: from -51°C to +135°C. Brittleness temperature: -75°C. Hardness: 64° Shore (A). Density: 0.98 g/cm³. Note: Product packaged in the Clean Room of Tubes International with strict standards maintained. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPressure hose, very flexible, resistant to aging, ozone, weather conditions, and abrasion. Designed for air, water, and light chemicals: non-oxidizing, diluted acids (e.g., hydrochloric and sulfuric), diluted bases, salt solutions, alcohols, acetone, ketones, glycol-based coolants. Not suitable for oils, fuels, aromatic hydrocarbons. Can be used for various water-soluble paints and those based on ketones and esters. Not suitable for cellulose paints, chlorinated rubber, and others containing aromatic solvents (e.g., toluene, xylene) or gasoline. Inner and outer layer antistatic R<106 Ω according to EN ISO 8031:2009. Inner layer: black EPDM rubber. Reinforcement: single or double (DN 32÷38) spiral textile braid. Outer layer: black EPDM rubber. Operating temperature: from -40°C to +120°C (temporarily up to +140°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and discharge hose intended for the transfer of industrial water, sewage, sludges, non-corrosive liquids, etc. Lightweight, flexible, resistant to kinks and vacuum. The outer layer is resistant to ozone and weather conditions. Commonly used for pumps in industry, construction, and agriculture. Installation – depending on the diameter and type of fittings using clamps, brackets, compression sleeves, tapes. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black SBR rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black SBR rubber. Working pressure: from 5 bar to 10 bar, depending on the hose diameter. Vacuum: 0.9 bar. Operating temperature: from -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, semi-transparent smooth-walled PTFE hose with excellent chemical resistance. Designed for low-pressure installations of chemicals, paints, fuels, oils, greases, air, gases, water, steam, and water-based fluids – in all types of industry. As it is chemically inert and does not contain components that could leach into the internal medium, it can be used for food substances. Compliant with FDA 21 CFR 177.1550, EU 10/2011, EC 1935/2004, and Italian D.M. 174 06/04/2004. The hose is not antistatic (does not dissipate electric charges for non-conductive substances). Not recommended for pneumatic plug connections. It can also be used as mechanical guidance for hoses or rods due to the low friction coefficient and self-lubricating properties of Teflon. Flame retardant (UL94 V-0) and with a high oxygen index (LOI). Safety factor n = 3:1. The burst and working pressure of the hose decreases at operating temperatures above 20°C and is dependent on its height. Hose material: PTFE (Teflon). Operating temperature: from -60°C to +260°C. Working pressure: from 3 bar to 56 bar - depending on the diameter and wall thickness of the hose.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible pressure hose made of PVC for general purposes and food products. Used for compressed air, water, water-based coolants, light chemicals, and liquid and semi-liquid food products. The smooth inner wall reduces flow losses and ensures ease of cleaning. In the food industry, it can be used for the transfer of hydrated, acidic foods, and alcohols up to 20%, e.g., juices, beverages, beer, wine (simulants A, B, C; up to +40°C and 0.5 h). Not recommended for milk and its derivatives, as well as food substances containing fats and oils. The RAGNO CR hose complies with European requirements 1978/142/EEC, 1935/2004/EC, 1895/2005/EC, and 10/2011/EU (simulants A, B, C), 2023/2006/EC (GMP). Suitable for temporary contact with food during the transfer of food substances - under the conditions specified in the manufacturer's declaration of conformity (available from Tubes International). Inner layer: transparent PVC. Reinforcement: polyester braid. Outer layer: transparent PVC. Working pressure for a temperature of 20°C: from 8 bar to 20 bar - depending on the hose diameter. The working pressure value decreases with increasing temperature. Operating temperature: from -5°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBlack flexible universal hose with exceptional resistance to aging, weather conditions, and ozone, with good chemical resistance. Resistant to temperatures in a wide range from -60°C to +135°C. Extremely flexible, elastic, with high fatigue resistance to deformation, resistant to abrasion. Excellent for use in peristaltic pumps. Used for transfer and dosing in industry and services, e.g., for dispensing soap and disinfectants, cleaning agents, caustic soda, etching and galvanizing chemicals, in glass and window washing systems, etc. The soft hose material (61° Shore (A)) is very flexible and provides excellent longevity of up to 1000 hours of operation in a peristaltic pump. The hose is an alternative to commonly used hoses made from traditional rubber blends such as EPDM and chloroprene. It has good chemical resistance to a range of chemicals, particularly acids and bases, oxidizing agents such as hydrogen peroxide, sodium hypochlorite, or ozone (300 pphm). Resistant to a variety of animal and vegetable fats. Not recommended for hydrocarbons. Resistant to aging and UV radiation. Characterized by low gas permeability compared to rubber hoses. Hose connection by welding is possible. The VACUUM version with thick walls is designed for continuous operation with vacuum and is resistant to cracking and aging. Full hose roll length: 15 m. Working pressure specified relative to burst pressure with a safety factor of 1:5. Material: norprene® - thermoplastic elastomer (TPE). Maximum operating temperature: +135°C. Brittleness temperature: -60°C. Hardness: 61° Shore (A). Density: 0.98 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsIndustrial hose for cold and hot water for heavy-duty conditions, requiring high flexibility, abrasion resistance, weather resistance, and ozone resistance. Used, among other applications, for cooling and thermostating injection molds. Can be used for air. Application at temperatures above +95°C reduces hose lifespan. Not oil-resistant, also not recommended for air with oil mist. Recommended installation with clamps or ferrules. Inner layer: black EPDM rubber. Reinforcement: synthetic braid. Outer layer: black, blue, or red EPDM rubber. Working pressure: 20 bar. Operating temperature: from -30°C to +95°C (20 bar), from -30°C to +140°C (10 bar), temporarily up to +160°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose designed for industrial cooling systems (an alternative to copper tubes) and automotive air conditioning (only for filling and testing functions). Specifically for refrigerants (R22, R134a, R404a, R407c, R410a, R507) and compressor oils of the POE and PAG types. The hose in sizes from 1/12" to 1/4" can also be used for CO2 (R-744) transmission - using CO2 as a refrigerant requires pressures approximately 10 times higher than conventional refrigerants. Inner layer: polyamide (PA), for diameters from 1/12" to 1/4" a PA and TPE (thermoplastic elastomer) blend. Reinforcement: polyester braid. Outer layer: micro-perforated, abrasion-resistant polyurethane. Working pressure: from 45 bar to 120 bar, depending on hose diameter. Operating temperature: from -45°C to +130°C (for water and air up to +70°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and discharge hose intended for the transfer of various chemical substances, mainly for acid, base, ketone, formaldehyde, industrial alcohol, and glycol solutions. Frequently used in industrial plants for draining contaminated water and process water. Also suitable for seawater. Inner and outer layer antistatic R≤106 Ω/m. Available pressure version (without steel spiral) - ORLANDO hose. Vacuum: 0.9 bar. Inner layer: black EPM (EPR) rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black EPM (EPR) rubber. Working pressure: 10 bar. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, very flexible and pliable hose designed for the discharge of chemically aggressive vapors and for operation at elevated temperatures. Good temperature resistance, good resistance to acid and solvent vapors. Also resistant to UV radiation, ozone, hydrolysis, and biological corrosion. Durable against bending. Used for mechanical vapor extraction, air conditioning, and ventilation in motor vehicles (buses, cars, and caravans, recreational boats, etc.), at air intakes for engines and compressors, in pellet and plastic dryers, in blow molding machines, etc. Other diameters ranging from 15 to 800 mm available on special order. The flame-retardant version P2SP SE complies with the requirements of DIN 4102 B1 for building materials. Hose material: polyester fabric impregnated with black TPE (thermoplastic elastomer). Wall thickness: 0.4 mm. Reinforcement: steel wire spiral. Operating temperature: from -40°C to +150°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight transparent smooth-walled hose made of natural (non-regenerated) fluoropolymer FEP (fluorinated ethylene propylene), a material with properties similar to PTFE. The hose features excellent chemical resistance, dimensional and shape thermal stability, and a smooth internal and external surface. Good transparency of the hose allows for easy observation of fluid level or flow. UV resistant. Designed for low-pressure installations of aggressive chemicals or where high purity and chemical inertness of the hose material are required. Commonly used in laboratories, chemical and pharmaceutical industries. Due to its excellent insulating properties, it is used in the electronics and semiconductor industries. The hose is not antistatic (does not dissipate electric charges for non-conductive substances). Not recommended for pneumatic plug connections. Flame retardant (UL94 V-0) and with a high oxygen index (LOI). Safety factor n = 4:1. Hose material: FEP. Shore hardness (D) 55. Operating temperature: from -200°C to +206°C. Working pressure: from 4.25 bar to 13 bar - depending on the hose diameter.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, resistant to kinks and atmospheric conditions welding hose for acetylene made according to ISO 3821 standard. Not recommended for gases produced from fuels, oils, and propane-butane (LPG). Inner layer: black SBR/NR rubber. Reinforcement: synthetic braid. Outer layer: smooth red SBR/NR rubber. Working pressure: 20 bar. Operating temperature: from -20°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong and flexible suction and discharge hose made entirely of abrasion-resistant polyurethane with high resistance to fats and oils. The hose is phthalate-free and can be used in the food industry for the transfer of liquid and dry food substances. This includes: - in particular, food fats and oils, e.g., olive oil (simulant D2; up to +40°C and 30 min); - milk and its derivatives, dairy beverages (simulant D1, up to +40°C and 30 min); - hydrated, acidic food, alcohol up to 20%, and dry food (simulants A, B, C, E; up to +70°C and 1 h). In applications not involving direct contact with food (in industry, construction, agriculture), it can be used for water, light chemicals, and other fat-based liquids as well as industrial oils (chemical resistance must be considered). Also used for air, vacuum transfer of dust, powders, granules, and other abrasive bulk materials (abrasiveness and potential static electricity issues must be considered). The very smooth inner surface reduces transmission losses and ensures ease of cleaning. The transparent wall allows for visual flow monitoring. Reinforcement with a dense steel wire spiral provides very good resistance to vacuum and hose collapse. The construction of the hose from polyurethane compared to similar PVC hoses results in significantly greater abrasion resistance, higher strength (working pressure and vacuum), and a wider temperature range with slightly less flexibility. The ARMORVIN TOTAL PU OIL TPHF hose complies with European regulations 1935/2004/EC, 1895/2005/EC, and 10/2011/EU (simulants A, B, C, D1, D2, E), 2023/2006/EC (GMP), and American FDA 21 CFR 177.2600 (d). Suitable for temporary contact with food during the transfer of food substances - under the conditions specified in the manufacturer's declaration of conformity (available from Tubes International). Hose material: transparent polyurethane. Reinforcement: galvanized steel spiral. Working pressure for a temperature of 20°C: from 3 bar to 7 bar - depending on the hose diameter. Operating temperature: from -40°C to +90°C, medium temperature, working pressure dependent on temperature. As the operating temperature increases, the working pressure value of the hose decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe HYPERLINE V (VISIFLON) hose is made of high-quality spiral corrugated PTFE, providing exceptional flexibility, elasticity, and vibration resistance among Teflon hoses. Like any Teflon hose, due to the unique properties of PTFE (wide operating temperature range, resistance to most substances and chemical compounds, minimal surface adhesion), the VISIFLON hose is perfectly suited for the transfer of chemicals, foodstuffs, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam, etc. In cases where there is a risk of static electricity (danger of charge generation and accumulation), VISIFLON hoses made of antistatic Teflon – the antistatic version AS – should be used. Antistatic Teflon is black (contains appropriately distributed graphite in PTFE) and has a resistance of R<108Ω (according to ISO 8031 annex A). This ensures the dissipation and dispersion of electric charges. The selection of the hose in the standard version made of natural PTFE or in the antistatic version should be confirmed with Tubes International. The SS version braid is made of annealed AISI 304 stainless steel wire and provides high pressure resistance. At operating temperatures above +130°C, the maximum working pressure should be reduced by 1% for every 1°C increase in temperature. Available versions of the inner layer: standard (natural white) and antistatic (black). Hose material: spiral corrugated PTFE (Teflon). Reinforcement: AISI 304 steel braid. Working pressure: from 20 bar to 60 bar - depending on the hose diameter. Operating temperature: from -70°C to +230°C. Resistant to full vacuum up to a temperature of: +130°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThick, strong, and flexible pressure hose compliant with the dimensions and requirements of standard EN ISO 6134:2005 type 2 class A (Ω), with steel reinforcement, intended for conveying saturated and superheated steam. The inner layer has good resistance to high temperature and saturated steam. It can be temporarily used for superheated steam at a temperature of 232°C and pressure of 18 bar; prolonged use with superheated steam reduces the hose's lifespan. The outer layer is resistant to temperature, weather conditions, abrasion, and aging. Antistatic R ≤106 Ω. The hose is used in the chemical, petrochemical, energy industries, and other industrial applications. It is not intended for steam cleaners ("dry steam cleaners"). For steam, use special screw-on fittings designed for steam. To extend the lifespan, the hose should be emptied of steam after use to avoid condensate accumulation. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black EPDM rubber. Reinforcement: double steel wire braid. Outer layer: black micro-perforated EPDM rubber. Working pressure: 18 bar. Operating temperature: from -40°C to +210°C (temporarily up to +232°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery flexible and lightweight suction and discharge hose intended for water, juices, beverages, and alcohols with a concentration of up to 20%, as well as other food products. Not suitable for fatty substances such as milk or oils. Resistant to vacuum and collapsing due to the embedded steel wire spiral in the hose wall. A significant advantage is its transparent wall resistant to UV radiation, allowing for easy visual monitoring of media flow, as well as the smoothness of its inner part reducing flow losses and ensuring ease of cleaning. Compared to the ARMORVIN HNA hose, it features higher working pressure and greater resistance to vacuum. In applications not involving direct contact with food (in industry, construction, agriculture), it can be used: 1) for light chemicals, water, sludges, and wastewater, other liquids (without fats, oils, and hydrocarbons); 2) for air, vacuum transfer of dust, powders, granules, and other lightly abrasive bulk substances (non-fatty). Abrasiveness and potential static electricity issues should be considered. As a hose reinforced with a steel spiral (without a braid), it exhibits some elongation under pressure, which should be taken into account in applications, especially at elevated temperatures. Standards and requirements: Food industry, contact with food: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B, and C), 2023/2006/EC (GMP). Hose material: light green transparent PVC. Reinforcement: galvanized steel spiral. Working pressure: from 2 bar to 8 bar, depending on the hose diameter. Operating temperature: from -5°C to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight smooth-walled hose made of PTFE with excellent chemical resistance in various color versions. Made from high-quality PTFE with added dye (material compliant with FDA). Flame retardant (UL94 V-0) and with a high oxygen index (LOI). Application for high-quality plug connections is possible. Safety factor n=4:1. The burst and working pressure of the hose decreases at operating temperatures above 20°C and is dependent on its height. Material: PTFE (Teflon), dyed. Shore hardness (D): 60. Working pressure: from 5.5 to 20 bar. Operating temperature: from -200°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible medium-thickness hose designed for the removal of dust, wood shavings, chips, bulk materials, granules, etc. Suitable for all types of industry, particularly commonly used for the removal of chips and other solid particles in the woodworking, furniture, ceramics, and plastics industries. The dense reinforcing spiral provides greater resistance to vacuum compared to ECO 0.4 and ECO 0.6 hoses. Flexible, less compressible, smooth inside, and elastic - even at low temperatures. Good abrasion resistance, also resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. The hose is marked with an arrow indicating the correct direction of medium flow. The wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. The hose is available in the following versions: ECO – standard version, ECO SE – flame-retardant material version (UL94 V-2), ECO AS – permanently antistatic version ISO 8031: R <109 Ω, TRGS 727 (6.4.2.4): R <2.5 x 108 Ωm, directive 2014/34/EU (ATEX): can be used in specific explosion hazard zones after risk analysis, ECO SE AS – antistatic and flame-retardant version (available on special request). The ECO hose is produced in a manufacturing process compliant with sustainable development policies, using raw materials from recycled clean production waste, renewable energy, closed water circulation, and other innovations. Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Wall thickness measured between the spiral: 0.7 mm. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCreamy-beige flexible hose, odorless and tasteless, non-toxic. Resistant to temperatures ranging from -60°C to +135°C. Extremely flexible, elastic, with high fatigue resistance to deformation, abrasion-resistant. Excellent for use in peristaltic pumps. Used for dispensing and portioning cold and hot food products, for soap, detergents, and disinfectants, for paints and toners, pesticides and fertilizers, as well as in laboratories. The soft hose material (61° Shore-A) is highly flexible and provides excellent longevity of up to 1000 hours of operation in a peristaltic pump. The hose is an alternative to commonly used PVC or silicone hoses. It has good chemical resistance to a range of chemicals, particularly acids and bases, oxidizing agents such as hydrogen peroxide, sodium hypochlorite, or ozone. Resistant to a variety of animal and vegetable fats. Not recommended for hydrocarbons. Resistant to aging and UV radiation. Meets FDA 21 CFR 177.2600 requirements for food contact. Multiple sterilization possible with steam in autoclaves, CIP and SIP cleaning in the installation, ethylene oxide, or radiation methods. Full hose roll length: 15 m. Material: TPE (Norprene® – thermoplastic elastomer). Maximum operating temperature: up to +135°C. Brittleness temperature: -60°C. Hardness: 61° Shore (A). Density: 0.98 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality suction and pressure hose "FULL OHM" completely antistatic (Ω/T), designed for the transfer of highly flammable and chemically aggressive substances. The inner layer is made of perfluoroalkoxy polymer PFA (fluoropolymer with properties similar to Teflon), antistatic (R<106 Ω), mirror-smooth, meeting high hygiene requirements (FDA, USP, European EU). Intermediate layers made of synthetic rubber, reinforced with synthetic cord and a steel wire spiral. The outer layer is MARBLE type (marbled), smooth, coated with polyethylene (UPE), antistatic (R<106 Ω), meeting FDA requirements, odorless and tasteless, resistant to abrasion, ozone and aging, chemicals, and short-term action of aggressive acids. An advantage of the MARBLE layer is its low friction coefficient - the hose glides and does not soil the surfaces it contacts, making it easy to clean. Excellent chemical resistance of PFA and antistatic properties of both the inner and outer layers (R<106 Ω) as well as across the wall of the hose (R<109 Ω) make the hose a costly but technically ideal solution for applications requiring the highest safety in all explosion hazard zones (ATEX). Used in the chemical, petrochemical, pharmaceutical, and cosmetic industries, as well as in biotechnology. Not intended for sterilization in an autoclave. A version with additional built-in copper wires (M/T) is available on special order. Standards and requirements: Chemical hoses: EN 12115:2011. Food industry, contact with food: 1935/2004/EC, 2023/2006/EC (GMP); inner layer: 10/2011/EU, USP Class VI, FDA 21 CFR 177.1550; ISO 10993-4,-10,-11, non-cytotoxic (ISO 10993 Part 5); outer layer: FDA 21 CFR 177.1520. Contains no plasticizers, phthalates, or animal-derived substances. Explosive atmospheres: ATEX Directive (zones: 0, 1, 2, 20, 21, 22), EN 50014/IEC 60079-0. Confirmation of resistance and application conditions requires contact with Tubes International. Assembly: Use smooth fittings with a spigot ("tail" for the hose) that do not have sharp or high ribs that could cut or damage the inner layer of PFA when tightened. The diameter of the spigot should be precisely matched to the diameter of the hose to ensure tightness. Assembly with clamp sleeves or shell clamps. Inner layer: black PFA polymer. Reinforcement: synthetic cord, steel spiral. Outer layer: white-black UPE polyethylene, synthetic rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: from -35°C to +130°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong pressure hose designed for cooling water in foundries, smelters, and all applications where rubber hoses operate close to a heat source. Glass fiber covering resistant to temperatures up to +530°C caused by thermal radiation. Used in cooling systems. Particularly recommended for water installations near metallurgical furnaces. Resistant to short-term exposure to splashes of molten hot metal. Non-conductive – electrical resistance of the rubber compound ≥108 Ω/m. Inner layer: white insulating EPDM rubber. Reinforcement: synthetic cord. Outer layer: EPDM rubber covered with glass fiber. Working pressure: 20 bar. Operating temperature: from -40°C to +120°C (external up to +530°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose designed for the transmission of LPG (liquid and gas) and natural gas. The outer layer is resistant to ozone and weather conditions. Antistatic (R <106 Ω/m). It has a copper wire ensuring electrical continuity between the hose ends. Manufactured according to standard EN 1762:2018, type D. Inner layer: black synthetic rubber. Reinforcement: synthetic braid. Outer layer: black micro-perforated synthetic rubber. Working pressure: 25 bar. Operating temperature: from -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality suction and discharge hose designed for the transfer of wine, beer, fruit juices, and other food substances free of fats, requiring the use of odorless and tasteless rubber. It is free from phthalates and bisphenol A. Designed for high-class wines and spirits, for use in breweries and distilleries. Widely used in the spirits industry for the transfer of strong alcohols with concentrations up to 96%. It features copper wires that ensure electrical continuity between the hose ends, enhancing the safety of transferring high-proof, flammable alcohol (ensure contact of the wire with the end during installation). The outer layer is resistant to abrasion, aging, and weather conditions. Standards and requirements: Food industry, food contact 1935/2004/EC, 2023/2006/EC (GMP). Inner layer compliant with FDA 21 CFR 177.2600, BfR XXI cat.2, D.M. 21/03/73. Inner layer: white butyl rubber (IIR). Reinforcement: synthetic cord, steel spiral. Outer layer: red butyl rubber (IIR). Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: from -40°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight and flexible suction and discharge hose for agriculture, food industry, and general applications. Designed for water, light chemicals, sludges and wastewater, plant protection products, and other liquids (excluding fats, oils, and hydrocarbons). Also suitable for air, vacuum transfer of dust, powders, granules, and other lightly abrasive bulk materials (non-greasy). Abrasiveness and potential static electricity issues should be considered. In the food industry, it can be used for the transfer of hydrated food, acidic substances, and alcohols up to 20%, e.g., juices, beverages, beer, wine (simulants A, B, C; up to +40°C). Not recommended for milk and its derivatives or food substances containing fats and oils. Reinforced with a hard PVC spiral, resistant to impact, ensuring good vacuum resistance and preventing hose collapse. The outer surface is corrugated, while the inside is smooth. The AGROFLEX LD hose complies with European regulations 1935/2004/EC, 10/2011/EU (simulants A, B, C), 2023/2006/EC (GMP). Suitable for temporary contact with food during the transfer of food substances - under conditions specified in the manufacturer's declaration of conformity (available from Tubes International). Hose material: green transparent PVC. Reinforcement: white spiral made of hard PVC. Working pressure at 20°C: from 2 bar to 6 bar. As the operating temperature increases, the working pressure value of the hose decreases. Operating temperature: from -10°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe hose is made of a smooth, seamless PTFE tube. The Teflon tube of the hose is extruded under strictly defined and controlled conditions, ensuring its highest quality, minimal porosity, and maximum flexibility and elasticity achievable for a smooth PTFE hose. The braid is made of annealed AISI 304 stainless steel wire with a high tensile strength of 1700 N/mm², with a strictly controlled angle of arrangement and tension of the braid wire bundles, resulting in minimal length changes of the hose under high pressure. Due to the unique properties of PTFE (wide operating temperature range, resistance to most substances and chemical compounds, negligible surface adhesion), the SMOOTHBORE hose is perfectly suited for the transfer of chemicals, foodstuffs, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam, etc. - as well as for classic high-pressure hydraulic oil installations. In cases where there is a risk of static electricity (danger of charge generation and accumulation), SMOOTHBORE hoses made of antistatic Teflon should be used – the antistatic version AS. The antistatic Teflon of version AS is black (contains appropriately distributed carbon in PTFE) and has a resistance R <10⁸ Ω (according to ISO 8031 annex A). This ensures the dissipation and dispersion of electric charges. The safety factor is 3:1; if a factor of 4:1 is required (e.g., according to EN 16643), the values should be multiplied by 0.75. At operating temperatures above +130°C, the maximum working pressure specified in the parameters should be reduced by 0.75% for each 1°C above this temperature. For example, at a temperature of 170ºC, the maximum working pressure for the hose AF-SWSB-06 is: 240 bar – (170°C-130°C) x 0.75 = 240 bar – 30% = 168 bar. The value "Wall thickness [mm]" provided in the Technical Data refers to the PTFE layer. Hose material: smooth PTFE (Teflon). Reinforcement: single braid of AISI 304 steel. Working pressure: from 55 bar to 240 bar - depending on the hose diameter. Operating temperature: from -70°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUnreinforced and highly flexible transparent PVC hose intended for non-pressurized (or very low-pressure) transfer of water, beer, wine, alcohols with a concentration of up to 20%, juices, beverages, and other food liquids. Not recommended for milk and dairy products, as well as oils and fatty food substances. Also used for liquids in general industrial applications, for light chemicals (e.g., diluted acids and bases), and as a protective cover for pipes, conduits, hoses, etc. For the hose, the stated pressure value is an indicative value of the recommended working pressure, assumed for a typical PVC hose, with a safety factor of 5:1. The use of the hose for a specific working pressure should be preceded by testing under working conditions. Standards and requirements: Food industry, contact with food: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B, and C), 2023/2006/EC (GMP). Hose material: transparent PVC. Working pressure: low, up to several bar, depending on temperature. Operating temperature: from -5°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsWidely used for washing floors and industrial equipment with hot water. Also suitable for outdoor use. Resistant to weather conditions and abrasion. Not resistant to oil, not recommended for air with oil mist. Compared to the "Tubes 2116," it has a thicker wall. Inner layer: white EPDM rubber. Reinforcement: polyester braid. Outer layer: red or blue micro-perforated EPDM rubber. Working pressure: 10 bar. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCreamy, flexible chemical hose with a multi-layer construction designed specifically to combine chemical resistance with high longevity in peristaltic pumps. Smooth inner layer with very good chemical resistance, free of plasticizers, resistant to acids, bases, salts, alcohols, and ketones, with low absorption and adsorption of water-based fluids. Outer layer made of thermoplastic elastomer (Norprene®) provides excellent properties and high longevity when used in peristaltic pumps. The hose meets hygiene requirements and is suitable for food contact: US FDA 21 CFR 177.1520 and is resistant to most cleaning and disinfecting agents. Sterilization by steam, ethylene oxide, or radiation. Ideal for dosing soap and detergents, laundry detergents, and dishwashing liquids. Used for the production and dosing of various chemicals in all sectors of industry. Full hose roll length is 15 m. The specified working pressure is defined relative to the burst pressure with a safety factor of 1:5. Material: polyolefin / TPE (Norprene® - thermoplastic elastomer). Operating temperature: from -60°C to +74°C. Brittleness temperature: -60°C. Hardness: 61° Shore (A). Density: 0.98 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, very flexible and elastic hose designed for the extraction of hot vapors, smoke, gases, blowing, and the discharge of cooling air. Reinforced version of the SILICONE 1 hose, featuring two layers of fabric coated with silicone and a steel spiral placed between the layers. Chemically resistant, UV resistant, and aging resistant. Used, among others, for gas extraction in the metallurgical industry, foundries, glass and ceramic industries, for hot air in industrial dryers, in printing houses and paper mills, in vehicles and engines for cooling air, incinerators, as well as for the extraction of exhaust gases and welding fumes. Smooth inside (when straightened), with a very small bending radius allowing easy installation in tight spaces of equipment and vehicles. Not recommended for continuous dynamic bending. Installation with clamps. Other diameters and lengths, soft ends of sections, etc., available on special order. Hose material: two layers of glass fabric coated with red silicone. Reinforcement: steel wire spiral, double external fiberglass cord. Operating temperature: from -70°C to +250°C (temporarily up to +300°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose with a smooth inner surface designed for compressed air, water, light chemicals, fungicides, fertilizers, and pesticides. Commonly used in agriculture for spraying, irrigation, and applications. The outer layer is resistant to abrasion and weather conditions. Inner layer: black PVC. Reinforcement: polyester braid (double polyester braid for REFITTEX 80 BAR version). Outer layer: black PVC. Working pressure at 20°C: 20 bar (white stripe), 40 bar (blue stripe), 80 bar for internal diameter 13 mm, above 50 bar (red stripe). As the operating temperature increases, the working pressure value of the hose decreases. Operating temperature: from -20°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDouble welding hose for oxygen and acetylene. Manufactured according to ISO 3821 standard. Inner layer: black synthetic rubber. Reinforcement: double polyester braid. Outer layer: smooth synthetic rubber in red (acetylene) and blue (oxygen). Working pressure: 20 bar. Operating temperature: from -32°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe unbraided version TO (Tube Only) of the VISIFLON hose, made of high-quality spiral corrugated PTFE (right-handed), provides exceptional flexibility, elasticity, and vibration resistance among Teflon hoses. The VISIFLON TO hose can be used for the transfer of chemicals, foodstuffs, fuels, oils, paints, solvents, adhesives, dyes, and detergents under very low pressure conditions. The standard version of VISIFLON TO is made of natural, translucent PTFE, allowing for visual flow control. The antistatic version VISIFLON TO AS made of carbon-infused Teflon (black) ensures the dissipation and dispersion of electric charges for substances and conditions at risk of static electricity. The hose material meets FDA requirements (21 CFR 177.1550 for VISIFLON TO, 21 CFR 178.3297 for VISIFLON TO AS). It is flame-retardant (UL94 V-0) and has a high oxygen index (LOI). Hose assembly requires straightening the corrugations along the length of the tail of the fitting, performed on special equipment. The fittings can then be installed by crimping with stainless steel ferrules. The working pressure value for the unbraided VISIFLON Teflon hose applies only up to a temperature of 100°C, and in the case of vacuum, up to a temperature of 80°C. Above these temperatures, there is a decrease in working pressure and vacuum. If the hose is to be used above these temperatures, this must be taken into account, and appropriate tests should be conducted under operating conditions. Hose material: spiral corrugated PTFE (Teflon). Operating temperature: from -70°C to +100°C (up to +230°C). Working pressure: from 2 bar to 4 bar - depending on the hose diameter.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe hose is made of a smooth, seamless PTFE tube. The Teflon tube of the hose is extruded under strictly defined and controlled conditions, ensuring its highest quality, minimal porosity, and maximum flexibility and elasticity achievable for a smooth PTFE hose. The heavy-duty HW version is recommended for harsher working conditions, gases (up to 100 bar), and applications where cyclic temperature changes occur. The braid is made of annealed AISI 304 stainless steel wire with a high tensile strength of 1700 N/mm², with a strictly controlled angle of arrangement and tension of the braid wire bundles, resulting in minimal length changes of the hose under high pressure. Due to the unique properties of PTFE (wide temperature range, resistance to most substances and chemical compounds, negligible surface adhesion), the SMOOTHBORE hose is perfectly suited for the transfer of chemicals, foodstuffs, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam, etc. - as well as for classic high-pressure hydraulic oil installations. In cases where there is a risk of static electricity (danger of charge generation and accumulation), SMOOTHBORE hoses made of antistatic Teflon should be used – the antistatic version AS. The antistatic Teflon of version AS is black (contains appropriately distributed carbon in PTFE) and has a resistance R <10⁸ Ω (according to ISO 8031 annex A). This ensures the dissipation and dispersion of electric charges. The safety factor is 3:1; if a 4:1 factor is required (e.g., according to EN 16643), the values should be multiplied by 0.75. At operating temperatures above +130°C, the maximum working pressure specified in the parameters should be reduced by 0.75% for each 1°C above this temperature. For example, at a temperature of 170°C, the maximum working pressure for hose AF-HWSB-06 is: 260 bar – (170°C-130°C) x 0.75 = 260 bar – 30% = 182 bar. The value "Wall thickness [mm]" provided in the Technical Data refers to the PTFE layer. Hose material: smooth PTFE (Teflon). Reinforcement: single braid of AISI 304 steel. Working pressure: from 55 bar to 240 bar - depending on the hose diameter. Operating temperature: from -70°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose designed specifically for the transfer of AdBlue® (AUS32, DEF) - 32.5% aqueous urea solution. The inner layer of the hose consists of black, smooth, antistatic (R‹10^6 Ω/m) EPDM rubber vulcanized without sulfur. The inner layer of the hose is free from contaminants such as aluminum, calcium, chlorine, copper, iron, potassium, magnesium, sodium, nickel, and zinc, ensuring the highest purity of the medium in accordance with ISO 22241-2. This is particularly important in the automotive industry, where AdBlue® acts as a reductant to decompose harmful nitrogen oxides in the SCR catalyst. Its use allows compliance with European emission standards EURO 4, 5, and 6. For AdBlue® to be effective, it must be very pure, necessitating the use of specialized hoses, tanks, and fittings that are resistant to AdBlue® and do not contaminate it. Ends and fittings for AdBlue® should be made of stainless steel or suitable plastic. Besides automotive applications, the hose is also used in the chemical industry, for example, in the production of nitrogen fertilizers. Inner layer: black EPDM rubber. Reinforcement: synthetic braid. Outer layer: black EPDM rubber. Working pressure: 10 bar or 20 bar. Operating temperature: from -40°C to +100°C (temporarily up to +120°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose designed for conveying saturated steam, with good resistance to high temperature, abrasion, and ozone. Available on request, hose according to standard EN ISO 6134:2005 type 1 class A. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black EPDM rubber. Reinforcement: synthetic cord. Outer layer: black EPDM rubber. Working pressure: 6 bar. Operating temperature: from -40°C to +165°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThick, strong hose designed for oxygen lances in the metallurgical industry. The outer layer is self-extinguishing and made according to ASTM C 542 standard. Inner layer: black CR rubber. Reinforcement: double textile cord, fiberglass spacer. Outer layer: yellow or blue CR rubber. Working pressure: 30 bar. Operating temperature: from -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMedium thickness, flexible hose designed for the removal of dust, wood shavings, chips, cuttings, lightweight bulk materials, etc. Specifically designed according to the requirements of the woodworking and furniture industries, it can also be used in other industrial fields. Compliant with DIN 26057 Type 2. Antistatic and flame-retardant, ensuring high workplace safety. Less flexible and compressible than SMARTFLEX® 0.4 and 0.6, but smooth inside, flexible even at low temperatures. With very good abrasion resistance, also resistant to microbes and hydrolysis. Free from halogen compounds and plasticizers. Resistant to oils and gasoline. The optimal direction of medium flow is marked with an arrow. The wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. Antistatic properties: permanently antistatic (according to ISO 8031 resistance R <109 Ω, according to German technical regulations TRGS 727 (6.4.2.4) specific resistance R < 2.5 x 108 Ωm, according to directive 2014/34/EU (ATEX) can be used in specific explosion hazard zones - which must be preceded by a risk analysis). After effective double grounding of the spiral, it can be treated as electrically conductive – in accordance with BGI 739-2 recommendations. Flame-retardant – according to DIN 4102 class B1. Hose material: transparent polyester-polyurethane. Wall thickness measured between the spiral: 0.7 mm. Reinforcement: steel wire spiral. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction and discharge hose designed for the transfer of food substances, requiring the use of odorless and tasteless rubber. It contains no phthalates or bisphenol A. Thanks to the steel spiral reinforcement, it has good resistance to vacuum. Suitable for milk and its derivatives, as well as wine, beer, and fruit juices. Not recommended for oils and fatty food substances. Widely used in the food industry. The outer layer of the hose is resistant to abrasion and weather conditions. Standards and requirements: Food industry, contact with food: 1935/2004/EC and 2023/2006/EC (GMP). D.M. 21/03/73, FDA 21 CFR 177.2600, BfR XXI cat. 2. Inner layer: white natural rubber (NR). Reinforcement: synthetic cord, steel spiral. Outer layer: blue EPDM rubber. Working pressure: 6 bar. Operating temperature: from -25°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose designed for hot water mixed with antifreeze fluids. Used in cooling and heating systems, for pumps in engines and machines. Inner layer resistant to heat and cooling fluids. Outer layer resistant to heat and aging. Manufactured according to standard DIN 73411:79. Roll length: 60 m or 120 m. Inner layer: black EPDM rubber. Reinforcement: synthetic cord. Outer layer: black EPDM rubber. Working pressure: from 2 bar to 4 bar - depending on the hose diameter. Operating temperature: from -40°C to +120°C.
