Light and flexible hose designed for the transport of air, dust, powders, wood shavings, fine chips, lightweight bulk materials, etc. Specifically designed according to the requirements of the woodworking and furniture industries, it can also be used in other industrial sectors. Antistatic and flame-retardant, it ensures high work safety. Flexible and elastic, even at low temperatures. Less compressible than the SMARTFLEX® 0.4 hose, but smoother on the inside. With very good abrasion resistance, also resistant to microbes and hydrolysis. Free from halogen compounds and plasticizers. Resistant to oils and gasoline. The optimal direction of medium flow is marked with an arrow. The wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. Antistatic properties: permanently antistatic (according to ISO 8031 resistance R <10⁹ Ω, according to German technical regulations TRGS 727 (6.4.2.4) specific resistance R < 2.5 x 10⁸ Ω, according to directive 2014/34/EU (ATEX) can be used in specific explosion hazard zones - which must be preceded by a risk analysis). After effective double grounding of the spiral, it can be treated as electrically conductive – in accordance with the recommendations of BGI 739-2. Flame-retardant – according to DIN 4102 class B1. Hose material: transparent polyester-polyurethane. Wall thickness measured between the spiral: 0.6 mm. Reinforcement: spiral made of steel wire. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).

Light, flexible, bendable, and nearly smooth inside hose designed for suction and transport of light materials with abrasive properties, such as dust, powders, granules, grains, flakes, and similar substances under low pressure. The hose is made of polyether-polyurethane and has good resistance to abrasion, ozone, weather conditions, hydrolysis, and biological corrosion. It is suitable for contact with food for the transport of bulk, dry food materials. It complies with European regulations 1935/2004/EC and 10/2011/EU (simulant E), 1895/2005/EC, 2023/2006/EC (GMP), and American FDA 21 CFR 177.2600 "d". It is suitable for temporary contact with food during the transport of dry, bulk, non-fatty food substances - under conditions specified in the manufacturer's declaration of conformity (available from Tubes International). Reinforcement with a hard PVC spiral provides good crush resistance. Used in various industrial applications, particularly in the food and agricultural industry, plastics, construction materials, etc. Versions: standard and antistatic - featuring a copper antistatic wire embedded on the outer side of the hose along the reinforcing spiral. Effective grounding of the wire ensures a sufficient level of electrostatic charge dissipation for many applications. The specified wall thickness of the hose is measured between the spiral. Hose material: transparent polyether-polyurethane. Reinforcement: hard PVC spiral. Operating temperature: from -25°C to +85°C.

Strong, flexible medium-thickness hose designed for the transport of chips, bulk materials, granules, etc. Suitable for all types of industries, particularly commonly used for the removal of chips and other solid particles in the woodworking, furniture, ceramics, and plastics industries. The medium-thick wall and dense reinforcing spiral provide higher pressure parameters compared to ECO hoses 0.4, 0.6, and 0.7. Very smooth on the inside, low compressibility, and flexible - even at low temperatures. Good abrasion resistance, also resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. The hose is marked with an arrow indicating the correct direction of medium flow. The wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. The hose is available in the following versions: ECO – standard version, ECO SE – flame-retardant material version (UL94 V-2), ECO AS – permanently antistatic version (ISO 8031: R <10⁹ Ω, TRGS 727 (6.4.2.4): R <2.5 x 10⁸ Ωm, directive 2014/34/EU (ATEX): can be used in specific explosion hazard zones after risk analysis), ECO SE AS – antistatic and flame-retardant version (available on special order). The ECO hose is produced in a manufacturing process compliant with sustainable development policies, using raw materials from recycled clean waste from the production process, renewable energy, closed water circulation, and other innovations. Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Wall thickness measured between the spiral: 1.0 mm. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).

Strong, flexible hose with a thick wall, designed for the discharge of chips, bulk materials, granules, etc. Suitable for all types of industry, particularly commonly used for discharging chips and other solid particles in the wood, furniture, ceramics, and plastics industries. The thick wall and dense reinforcing spiral ensure high pressure parameters. Very smooth on the inside, low compressibility, and flexible - even at low temperatures. Excellent abrasion resistance, also resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. The hose is marked with an arrow indicating the correct direction of medium flow. The wall thickness of the hose is measured between the spiral. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. The hose is available in the following versions: ECO – standard version, ECO SE – version made of flame-retardant material (UL94 V-2), ECO AS – permanently antistatic version (ISO 8031: R <10⁹ Ω, TRGS 727 (6.4.2.4): R <2.5 x 10⁸ Ωm, directive 2014/34/EU (ATEX): can be used in specific explosion hazard zones after risk analysis), ECO SE AS – antistatic and flame-retardant version (available on special request). The ECO hose is produced in a manufacturing process compliant with sustainable development policies, using raw materials from recycled clean production waste, renewable energy, closed water circulation, and other innovations. Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Wall thickness measured between the spiral: 1.4 mm. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).

Very lightweight, flexible hose designed for the transport of air, vapors, dust, fine particles, powders, grains, and lightweight bulk materials. Intended for use in the food and pharmaceutical industries. Highly flexible and very compressible axially, also elastic at low temperatures. Good abrasion resistance, resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. The hose is available in the following versions: P2 PU FOOD – steel wire (copper-plated) spiral; P2 PU PAS FOOD – stainless steel wire spiral, hose material permanently antistatic (R ≤ 10⁸ Ω, according to TRGS 727). P2 PU FOOD and P2 PU PAS FOOD hoses comply with European regulations 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP), and American FDA 21 CFR 177.2600 and 178.2010. Suitable for temporary contact with food during the transfer of dry, bulk, non-fatty food substances - under the conditions specified in the manufacturer's declaration of conformity (available from Tubes International). Hose material: transparent polyether-polyurethane. Wall thickness measured between the spiral: 0.4 mm. Reinforcement: steel wire spiral (P2 PU FOOD), stainless steel wire AISI 301 spiral (P2 PU PAS FOOD). Operating temperature: from -40°C to +100°C (temporarily up to +125°C).

Strong, thick, flexible hose designed for suction and transport of granules and other bulk materials. Intended for use in various types of industry. Used for plastic granules, insulation materials, waste, sand, and other construction materials. Quite flexible, low compressibility, smooth inside, elastic even at low temperatures. Good abrasion resistance, resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. Installation on couplings with bridge clamps (right-handed). Other diameters may be available. In addition to the standard version P7 M PU AE, the hose is available in the P7 M PU EL version, which is electrically conductive (R ≤10⁴ Ω), compliant with ATEX 2014/34/EU, TRBS 2153, and for suction also with TRGS 727, it can be used in explosion hazard zones after conducting a risk assessment. Hose material: polyester-polyurethane. Wall thickness measured between the spiral: 1.4 mm. Reinforcement: spiral with steel wire. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).

Lightweight, flexible medium-thickness hose designed for the extraction and transport of powders, grains, light granules, and other bulk materials. Intended for use in the food and pharmaceutical industries. Used, among others, for powdered milk, grains, rice, coffee, tea, flour (PAS version). Flexible, fairly compressible, almost smooth inside, elastic even at low temperatures. Good abrasion resistance, resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. The hose is available in the following versions: P7 OL PU FOOD – steel wire (copper-plated) spiral; P7 L PU PAS FOOD – stainless steel spiral, hose material permanently antistatic (R ≤10⁸ Ω, according to TRGS 727). The P7 OL PU FOOD and P7 L PU PAS FOOD hoses comply with European requirements 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP), and American FDA 21 CFR 177.2600 and 178.2010. Suitable for temporary contact with food during the transport of dry, bulk, non-fatty food substances - under the conditions specified in the manufacturer's declaration of conformity (available from Tubes International). Hose material: transparent polyether-polyurethane. Wall thickness measured between the spiral: 0.7 mm. Reinforcement: steel wire spiral (P7 OL PU FOOD), stainless steel AISI 301 wire spiral (P7 L PU PAS FOOD). Operating temperature: from -40°C to +100°C (temporarily up to +125°C).

Hose designed for the removal of dust, wood shavings, and chips in the woodworking and furniture industry. Designed for CNC machines for wood and plastic processing: machining centers, vertical milling machines, milling plotters. The thick steel spiral coated with white PVC is corrosion-resistant, has good adhesion to the hose material, and provides high pressure parameters. Despite its strong construction, due to the optimally selected large spiral pitch, it is very flexible, bendable, and compressible. Particularly recommended for dust and chip extraction from rapidly moving working heads (CNC Router Dust Collection System). Resistant to microbes, hydrolysis, as well as oils and gasoline. Does not contain halogen compounds and plasticizers. Flame-retardant, compliant with the German standard DIN 4102 class B1. The hose can be treated as electrically conductive after grounding the spiral, in accordance with German industrial recommendations BGI 739-2. Installation on couplings with bridge clamps (right-handed). Other diameters in the range of 80 ÷ 600 mm available on special order. Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral coated with white PVC. Operating temperature: from -40°C to +100°C.