Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong, thick, flexible hose designed for suction and transport of abrasive bulk materials, granulates, roofing gravel, industrial cleaning, abrasive for sandblasting, silos, bulk material tankers, etc. Compliant with DIN 26057 Type 4 (SMARTFLEX® 2.0). Antistatic and flame-retardant, ensuring high workplace safety. Thick wall and dense, robust reinforcing spiral provide high resistance to vacuum. Smooth inside, non-compressible, not very flexible but elastic, even at low temperatures. Very good abrasion resistance, also resistant to microbes and hydrolysis. Free from halogen compounds and plasticizers. Resistant to oils and gasoline. The optimal flow direction of the medium is marked with an arrow. The wall thickness of the hose is measured between the spiral. Other diameters may be available upon special request. Antistatic properties: permanently antistatic (according to ISO 8031 resistance R <109 Ω, according to German technical regulations TRGS 727 (6.4.2.4) specific resistance R < 2.5 x 108 Ωm, according to directive 2014/34/EU (ATEX) can be used in specific explosion hazard zones - which must be preceded by a risk analysis). After effective grounding of the spiral on both sides, it can be treated as electrically conductive – in accordance with BGI 739-2 recommendations. Flame-retardant – according to DIN 4102 class B1. Wall thickness measured between the spiral: 2.0 mm (SMARTFLEX® 2.0), 2.5 mm (SMARTFLEX® 2.5). Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone elbow 180° reinforced with polyester is intended for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, a version with a fluorosilicone inner layer is recommended. Standard arm length: 102 mm. Pressure safety factor: 3:1. The hose meets SAE J20R1 standards. Hardness (standard version) approx. 65° Shore (A), density approx. 1.26 g/cm³. Color of the outer layer: blue. Material: silicone rubber. Reinforcement: polyester spacers. Working pressure: from 2 bar to 8.12 bar (depending on hose diameter). Operating temperature: from -50°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, crystal-clear, flexible chemical hose with a multi-layer construction featuring an inner layer made of FEP fluoropolymer with unique resistance and chemical inertness. It exhibits significantly greater flexibility than rigid hoses made entirely of Teflon or other fluoropolymers. The smooth inner layer, resistant and chemically inert, eliminates the risk of fluid contamination. Resistant to a wide range of chemicals from corrosive substances to MEK-based solvents. The hose meets hygiene requirements and is suitable for food contact: US FDA 21 CFR 177.1550, free from phthalates and BPA (Bisphenol A), non-toxic, and does not leave any odor or taste. Sterilization with ethylene oxide. Used in various industrial applications: chemical flow, pharmaceuticals, food and beverage production and packaging, paint, solvent and adhesive manufacturing, inks and toners, photographic chemicals, fertilizers and pesticides, in semiconductor production. Full hose roll length: 15 m. Working pressure defined relative to burst pressure with a safety factor of 1:5. Material: special FEP / PVC. Maximum operating temperature: +74°C. Brittleness temperature: -36°C. Hardness: 66° Shore (A). Density: 1.21 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight and flexible flat-folded suction hose with fittings for water for fire pumps. Used for fire, rescue, and forestry motor pumps. In addition to fire-fighting functions, widely used for water transfer in industry, construction, agriculture, and mining. The inner layer is smooth, resistant to mold and rot. The outer layer (braid) has high strength, with a polyurethane coating that does not retain dirt, increasing resistance to abrasion and contact with flames. Certifications: hoses compliant with the technical conditions of the MSWiA Regulation of April 27, 2010, hoses with fittings (complete hoses) have CNBOP-PIB approval certificates. Inner layer: smooth polyurethane. Reinforcement: polyester braid. Outer layer: red polyurethane coating. Working pressure: from 12 bar to 15 bar - depending on the hose diameter. Operating temperature: from -30°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone pressure hose REDSIL has versatile applications over a wide temperature range. It is used for both hot air and, for example, in cooling systems. Designed for liquids and gases, it is employed in various industrial sectors, including the chemical industry. Inner layer: transparent silicone. Reinforcement: olpot PET (polyester). Outer layer: red silicone. Hardness: 70° ±5° Shore (A). Operating temperature: from -50°C to +200°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible suction and discharge hose intended for the transport of food, pharmaceutical, and cosmetic substances: water, fruit juices, beer, wine, vinegar, alcohols up to 96% concentration, milk and its derivatives, creams, soaps, aromatic substances, pigments, and others. Resistant to fats and oils in standard usage conditions. It has good chemical resistance to light chemicals – solutions of acids and bases. Extruded, completely smooth inner and outer surface of the hose facilitates flow and cleaning. Reinforced with a spiral of stainless steel wire embedded in a TPE-S wall, making it resistant to vacuum and collapsing. The transparent wall allows for easy visual monitoring of flow. The hose material is non-vulcanized, clean (without vulcanization additives), resistant to hydrolysis, does not promote bacterial growth, has low porosity and low permeability. Completely neutral in taste and odor, does not alter the organoleptic properties of the medium. Resistant to aging, weather conditions, and UV radiation. Cleaning by SIP method is not recommended, as it significantly shortens the service life. Use for high-proof alcohol (its vapors or other flammable substances) requires consideration of hazards related to static electricity. As a hose reinforced only with a spiral (without a braid), it exhibits some elongation under pressure, therefore the maximum working pressure of the hose is low (safety factor 1:5). Hose cleaning, disinfection, or sterilization should be carried out strictly according to the recommendations provided in the catalog sheet below. Standards and requirements: 1) Food industry, contact with food: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulation fluids A, B, C, D1, D2), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 “e”. 2) Pharmaceutical industry USP CLASS VI. Hose material: transparent TPE-S. Reinforcement: AISI 302 steel spiral. Working pressure: from 1 bar to 1.5 bar, depending on the hose diameter. Operating temperature: -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone elbow 45° reinforced with polyester is intended for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, a version with a fluorosilicone inner layer is recommended. Arm length: 100 mm (also available with arm lengths of 152, 250 mm). Pressure safety factor: 3:1. The hose meets SAE J20R1 standards. Hardness (standard version) approx. 65° Shore (A), density approx. 1.26 g/cm³. Color of the outer layer: blue. Material: silicone rubber. Reinforcement: polyester inserts. Working pressure: from 1.5 bar to 8.33 bar (depending on hose diameter). Operating temperature: from -50°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong, thick, flexible hose designed for suction and transport of abrasive bulk materials: granules, grains, sand, gravel. Thick wall and very dense reinforcing spiral ensure high resistance to pressure and vacuum. Very smooth inside, non-compressible, not very flexible (r=4xD), retains its elasticity even at low temperatures. Hose with good abrasion resistance, also resistant to oils and gasoline. Installation on couplings with bridge clamps (right-handed) or special installation on industrial ends, e.g., flanges. Other diameters may be available upon special request. Versions: P3 S PU – standard version, made of polyester-polyurethane, very abrasion-resistant, and P3 S PU AE - version made of polyether-polyurethane, with good abrasion resistance, resistant to microbes and hydrolysis; approved for contact with food substances, compliant with European regulations 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP), and American FDA 21 CFR 177.2600 and 178.2010. Suitable for temporary contact with food during the transport of dry, bulk, non-fatty food substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International); P3 S PU AS – antistatic version (R ≤108 Ω), compliant with TRBS 2153 and for suction also with TRGS 727, made of polyether-polyurethane, with good abrasion resistance, resistant to microbes and hydrolysis. Hose material: transparent polyester-polyurethane (P3 S PU), transparent polyether-polyurethane (P3 S PU AE and P3 S PU AS). Wall thickness measured between the spiral: 2 mm. Reinforcement: dense spiral made of steel wire. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsKnown and proven for years, a lightweight and soft natural rubber hose in light brown color. Easy to install due to its softness (hardness 40° Shore – A), flexibility, and elasticity (maximum elongation 500%). It has properties similar to latex. Abrasion-resistant, with good resistance to acids and bases. Used for liquids and gases, for various industrial applications such as dispensing and dosing soaps and detergents, alcoholic and dairy products, laboratories. Sterilization with steam for 30 minutes (1 bar, 141°C) or ethylene oxide. Full hose roll length is 50 m (from inner diameter 7 mm - 25 m). The specified working pressure is determined relative to the burst pressure with a safety factor of 1:5. Material: natural rubber (NR). Operating temperature: from -35°C to +70°C (120°C for moist heat). Brittleness temperature: -40°C. Hardness: 40° Shore (A). Density: 0.98 g/cm³. Note: Product packaged in the Clean Zone of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and discharge hose intended for the transfer of pharmaceutical products, cosmetics, food substances, and chemicals (selection according to the principles in the chapter "Chemical Hoses"). It does not contain plasticizers, phthalates, or animal-derived substances. It is characterized by high thermal and mechanical strength. It is an excellent solution for processing industries requiring the highest safety during the transfer of high-purity products. The outer layer is resistant to abrasion, ozone, and weather conditions. It has two copper wires ensuring electrical continuity between the hose ends. Standards and requirements: 1) General EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) Food industry, contact with food 1935/2004/EC and 2023/2006/EU (GMP). The inner layer complies with 10/2011/EC, D.M. 21/03/73, FDA 21 CFR 177.1550. The outer layer complies with FDA 21 CFR 177.2600, D.M. 21/03/73. 3) Pharmaceutical industry USP Class VI (inner layer). Installation: use smooth fittings with a spigot ("tail" to the hose) that do not have sharp or high ribs that could cut or damage the inner layer made of MFA when tightened. The diameter of the spigot should be precisely matched to the diameter of the hose to ensure tightness. Installation with clamp sleeves or shell clamps. Inner layer: smooth fluoropolymer MFA. Reinforcement: synthetic cord, steel spiral. Outer layer: smooth EPDM rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: -50°C to +170°C (for most chemicals).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose designed for the transmission of compressed air, for compressors, hammers, drills, and other pneumatic tools. Due to its low weight, flexibility, robust construction, and high working pressure, it has been accepted and successfully used for many years in construction (particularly in demolition companies), industry, and mining. Extremely durable and long-lasting due to high-quality materials and construction. Reinforced with a circumferentially woven polyester braid completely bonded and surrounded by rubber in the original hot extrusion process of the rubber mixture through the braid. UV resistant. The inner layer is smooth, ensuring minimal flow loss. The yellow, ribbed outer surface is resistant to abrasion, oils, and ozone, and is highly visible on construction sites. Flat when at rest, facilitating handling and storage. Resistant to longitudinal loads. Most commonly used with air couplings (spacing 42 or 41 mm) mounted with cast iron clamps (ordered separately). Also available in black. Use for high-pressure air should always be preceded by a risk analysis in the event of accidental disconnection or rupture of the hose and potential application of safeguards. Maximum working pressure established according to a safety factor of 4:1 approved by the manufacturer for air. Exceeding 1/3 of the specified breaking force is not recommended. Standard roll length: 200 m. Hose material: yellow NBR/PVC mixture with UV-resistant barrier, embedded in the polyester braid during the hose extrusion process. Working pressure: from 12.5 bar to 25 bar - depending on the hose diameter and temperature. Operating temperature: from -30°C to +75°C (temporarily up to +80°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible, popular general-purpose PVC hose. Used for air, water, and light chemicals in industry, agriculture, horticulture, and for domestic use. Roll length: 60 meters. Inner layer: transparent PVC. Reinforcement: polyester braid. Outer layer: transparent PVC. Working pressure at 20°C: from 10 bar to 15 bar - depending on the hose diameter and decreases with increasing temperature. Operating temperature: from -5°C to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone reducer connector reinforced with polyester is intended for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, the version with a fluorosilicone inner layer is recommended. Standard length: 102 mm. Pressure safety factor: 3:1. The hose meets SAE J20R1 standards. Hardness (standard version) approx. 65° Shore (A), density approx. 1.26 g/cm3. Color of the outer layer: blue. Material: silicone rubber. Reinforcement: polyester spacers. Working pressure: from 1 bar to 7.33 bar (depending on hose diameter). Operating temperature: from -50°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal, highly flexible, unreinforced hose designed for non-pressurized (or very low pressure) transfer of water, beer, wine, alcohols, juices, and beverages. The absence of phthalates in the hose material makes it suitable for the transfer of milk and its derivatives, as well as alcohols with a volumetric concentration of up to 50% and temperatures up to +40°C. Not recommended for oils and fatty food substances. Also used for liquids in general industrial applications, for light chemicals (acids, bases), for solid substances (powders), and as protection for pipes, conduits, hoses, etc. For the hose, the stated pressure value is an indicative value of the recommended working pressure, assumed for a typical PVC hose, with a safety factor of 5:1. The use of the hose for a specific working pressure should be preceded by testing under working conditions. Standards and requirements: Food industry, food contact: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulated fluids A, B, C, and D1), 2023/2006/EC (GMP). Hose material: transparent PVC. Working pressure: low, up to several bar, depending on temperature. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong and flexible rubber pressure hose, intended for water, paints, light chemicals, and air. Can be used for water-based epoxy and polyurethane dispersion paints. Not suitable for cellulose paints, chlorinated rubber, and others containing aromatic solvents such as toluene, xylene, or gasoline, as well as for oils, fuels, and aromatic hydrocarbons. For chemical applications, we recommend contacting Tubes International. Conductive inner and outer layer (R<105 Ω/m), outer layer resistant to ozone, aging, and weather conditions. Inner layer: black EPDM rubber. Reinforcement: polyester braid (DN6 ÷ DN25), 2 polyester braids (DN32 ÷ DN38). Outer layer: black EPDM rubber. Working pressure: 20 bar. Operating temperature: from -40°C to +95°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, strong suction and discharge hose designed for water and sewage. Externally corrugated, internally almost smooth. Good resistance to external damage and harsher operating conditions. Maintains high flexibility at low temperatures. Used in irrigation systems, industrial water installations, for emptying septic tanks, etc. A special version, ARIZONA EXTREME ELASTIC, is also available on special order, flexible at very low temperatures (down to -40°C). Hose material: gray and green PVC. Reinforcement: hard PVC spiral. Working pressure: from 1.5 bar to 7 bar - depending on the hose diameter and temperature. Operating temperature: from -25°C to +55°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible and bendable, temperature-resistant two-layer suction and discharge hose designed for the removal and transfer of vapors, fumes, and high-temperature air. Flame-retardant, chemically resistant, with fairly good resistance to hot sparks. Used in the construction of furnaces (metal and glass foundries, ceramic and chemical industries), vehicles (exhaust gas discharge systems, engine testing stations, etc.), aerospace and military applications. Characterized by high compressibility - up to 1:6, strong construction, and impact resistance due to the external spiral. Also available with a stainless steel spiral (from a diameter of 80 mm). Hose installation on couplings with bridge clamps (left-handed). Standard length: from 2 to 10 m - contact Tubes International. Hose material: 2 layers of glass fabric, with the outer layer coated in silicone (gray). Reinforcement: external spiral made of galvanized steel wire and sheet. Operating temperature: from -50°C to +450°C (temporarily up to +500°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, transparent, flexible fuel hose with exceptionally low fuel vapor permeability through the hose wall. Meets American EPA and CARB requirements (permeability up to 15 g/m2/24h). Patented multi-layer hose construction with an inner layer of PVDF fluoropolymer resistant to fuels containing up to 100% ethanol. Resistant to swelling and hardening due to hydrocarbons, significantly reduces the risk of cracking and leakage. Minimal extractability ensures fuel purity, and the exceptionally low aromatic substance permeability protects the operator and the environment. Ozone and UV radiation resistant (ANSI B175.1 D). The flexibility of the hose facilitates installation even in tight spaces and is maintained at low temperatures, ensuring hassle-free fuel withdrawal in any position. The transparent wall allows for flow monitoring. Thanks to the inner layer of PVDF, the hose is resistant to most chemicals and fuels. It can be submerged in fuel (only not recommended for repeated use at high external temperatures). Flame retardant (UL 94 HB). Used in modern lawn mowers, chainsaws, gas drills, hedge trimmers, and other gardening machines. Full hose roll length is 15 m. Working pressure defined relative to burst pressure with a safety factor of 1:5. Material: PVDF / TPE (multi-layer). Operating temperature: from -40°C to +82°C. Brittleness temperature: -90°C. Hardness: 78° Shore (A). Density: 1.27 g/cm³. Note: Product packaged in the Clean Zone of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, very soft, extremely flexible and elastic hose characterized by high resistance to bending and lack of shape memory. Designed for air, water, and light chemicals. Maintains flexibility at low temperatures. Outer layer resistant to abrasion. Resistant to UV radiation and weather conditions. Hose material free from cadmium and silicone, complies with RoHS requirements. Roll length: 100 m. Inner layer: yellow (Y) or blue (BL) PVC. Reinforcement: polyester braid. Outer layer: yellow (Y) or blue (BL) PVC. Working pressure at 20°C: 20 bar. As the operating temperature increases, the working pressure value of the hose decreases. Operating temperature: from -25°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong and durable high-quality flat hose designed for trouble-free and maintenance-free operation in harsh field conditions. Used particularly for water, sludge, sewage, and other liquids. Made from hydrolysis and microbe-resistant polyurethane - polyether. Reinforced with a circumferentially woven polyester braid bonded and surrounded by polyurethane in the original hot thermoplastic polyurethane extrusion production process through braiding. The hose has high tensile strength, minimal elongation under pressure, and no tendency to kink or twist. Excellent abrasion and puncture resistance allows operation in heavy, uneven terrain and minimizes wear on the water-loaded hose during possible pressure pulsations. Due to its strength and durability combined with ease of handling (rewinding - unwinding), it is used in permanent and temporary high-pressure and high-efficiency water systems in the mining, energy, agriculture, and firefighting industries. Resistant to a wide range of chemicals, microbes, fungi, hydrolysis, weather conditions, UV, and ozone. To confirm the resistance and application conditions of the hose, contact Tubes International. Maximum working pressure for temporary use established according to a safety factor of 2:1 approved by the manufacturer (only for water and safe, non-flammable liquids). For maximum longevity, it is not recommended to exceed 1/3 of the bursting pressure. Standard roll length: 200 m. Hose material: black polyurethane - polyether (PU). Working pressure: from 15 bar to 21 bar - depending on the hose diameter and temperature. Operating temperature: from -50°C to +75°C (water).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone hose reinforced with meta-aramid is intended for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, a version made of fluorocarbon rubber is recommended. Standard length: 1000 mm (also available in lengths of 2000 mm and 3000 mm). Pressure safety factor: 3:1. The hose meets SAE J20R1 standards. Outer layer color: blue. Material: silicone rubber. Reinforcement: meta-aramid layers. Working pressure: from 1 bar to 8.75 bar (depending on hose diameter). Operating temperature: from -50°C to +230°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, glassy transparent, flexible hose free of phthalates and BPA (Bisphenol A). Designed for the transfer and dispensing of food products, particularly juices, beverages, and bottled water. Does not alter the taste and smell of products, and its non-wetting properties allow for complete drainage and easy cleaning by rinsing. Can be used with peristaltic pumps, but the lifespan is moderate. Meets hygiene and food contact requirements: European 1935/2004/EC and 10/2011 EU (for conditions and substances according to certification), American FDA, NSF-51, NSF61, 3-A, Japanese #370/1959 and MHLW370(3-D). Sterilization by steam or ethylene oxide is possible. Compliant with REACH and California Proposition 65 – does not contain hazardous and prohibited substances. Full hose roll length is 15 m (from internal diameter 50.8 mm - 6 m). The specified working pressure is relative to the burst pressure with a safety factor of 1:5. Material: PVC (special). Maximum operating temperature: +74°C. Brittleness temperature: -36°C. Hardness: 66° Shore (A). Density: 1.21 g/cm³. Note: Product packaged in the Clean Zone of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone anti-vibration connector with one notch reinforced with polyester is intended for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, the version with fluorocarbon rubber is recommended. Pressure safety factor: 3:1. Complies with SAE J2006 R3 standard. Hardness (standard version) approx. 65° Shore (A), density approx. 1.26 g/cm³. Color of the outer layer: blue. Material: silicone rubber. Reinforcement: polyester spacers. Operating temperature: from -50°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose designed for the discharge of hot exhaust gases from gasoline and diesel engines. Used as a workshop hose deployed on the floor, adapted for drum winding systems, as a suction duct, or at engine testing stations. Resistant to crushing due to reinforcement with a thick, white, round nylon spiral (PA), covered externally with black TPE. Chemically resistant, particularly to gasoline and oil vapors, as well as ozone, hydrolysis, microbes, and UV radiation. Halogen-free and free of plasticizers. The P-G-EX 1 hose should be used with a vacuum exhaust gas removal system, employing the appropriate coupling between the hose and the engine exhaust outlet. Other diameters ranging from 40 to 250 mm are available on special order. Hose installation on couplings with bridge clamps (right-handed). Standard lengths: 2.5 m, 5 m, 7.5 m, 10 m, 15 m, and 20 m. Hose thickness measured between the spiral: 0.4 mm. Hose material: polyester fabric impregnated with a black TPE coating (thermoplastic elastomer). Reinforcement: nylon spiral in a TPE protective cover against abrasion. Operating temperature: from -40°C to +150°C (temporarily +170°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction and discharge hose with thick walls, designed for the transfer of food substances requiring the use of odorless and tasteless rubber. It contains no phthalates or bisphenol A. The hose is specially designed for the transfer of oils and fats. Widely used in the oil and fat industry. The outer layer is resistant to grease and aging. Standards and requirements: Food industry, food contact 1935/2004/EC and 2023/2006/EC (GMP). The inner layer complies with FDA 21 CFR 177.2600, D.M. 21/03/73. Inner layer: white NBR/PVC rubber. Reinforcement: two layers of synthetic cord, steel spiral. Outer layer: blue smooth CR rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: -15°C to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal flexible high-quality polyurethane hose produced in the United Kingdom. Designed for water, air, oils, fuels, lubricants, chemicals, and granules. As a non-reinforced hose, it is suitable for very low pressure up to several bar and as a protective hose. The crystal-clear wall allows for excellent observation of the medium. The smooth inner surface facilitates flow and cleaning. Stronger than similar PVC hoses, better at maintaining its shape, well resistant to kinking, flexible at low temperatures. Made from polyurethane – polyether, resistant to hydrolysis and abrasion. Contains no cadmium, silicone, plasticizers, or halogen compounds. According to EU regulations, use for food products is possible after conducting the required migration tests using appropriate model liquids simulating the specific type of food (the material used for hose production complies with FDA requirements 21 CFR 175.105, 177.1680, 177.2600, and WRAS for water at 23°C). Hose material: soft, transparent polyurethane (polyether) free of phthalates. Operating temperature: from -30°C to +70°C (temporarily up to +100°C). Brittleness temperature: -70°C. Recommended working pressure value: from 2.5 bar to 4.8 bar - depending on the hose diameter. As the operating temperature increases, the working pressure value of the hose decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVacuum-resistant suction and discharge hose designed for cooling water in foundries, smelters, and all applications where rubber hoses operate close to a heat source. Glass fiber covering resistant to temperatures up to +530°C caused by thermal radiation. Used in cooling systems. Particularly recommended for water installations near metallurgical furnaces. Resistant to short-term exposure to splashes of molten hot metal. Standard length: 60 m or 120 m. Inner layer: black SBR rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: EPDM rubber / glass fiber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: from -40°C to +70°C, external up to +530°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone reducing elbow 90° reinforced with polyester is intended for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, a version with a fluorosilicone inner layer is recommended. Standard arm length: 102 mm. Pressure safety factor: 3:1. The hose meets SAE J20R1 standards. Hardness (standard version) approx. 65° Shore (A), density approx. 1.26 g/cm³. Color of the outer layer: blue. Material: silicone rubber. Reinforcement: polyester inserts. Working pressure: from 1 bar to 7.33 bar (depending on hose diameter). Operating temperature: from -50°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPneumatic extension - ready air hose made of SOFT PLUS. Finished with a brass socket and Eurostandard DN7.2 plug compatible with commonly available quick couplings on the market. Equipped with bend restrictors. Ideal solution for connecting pneumatic tools, easy to operate, vibration-damping. Ensures a high standard of operator work. Available lengths: 10 or 15 m. Inner layer: yellow (Y) or blue (BL) PVC. Reinforcement: polyester braid. Outer layer: yellow (Y) or blue (BL) PVC. Working pressure at 20°C: 20 bar and decreases with increasing working temperature. Operating temperature: from -25°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, very flexible and elastic, resistant to creasing and twisting hose designed for the removal of dust, contaminated air, and welding fumes. Commonly used in industrial vacuum systems. The external reinforcing spiral shaped in the profile of the hose, left-handed, allows for the attachment of appropriate fittings for vacuums with left-handed threads (plastic fittings with index ME-EVA...). Hose installation is also possible using clamps on appropriate ends, pipe fittings, etc. Hose material: gray ethylene-vinyl acetate (EVA). Reinforcement: reinforcing spiral shaped in the profile of the hose. Operating temperature: from -30°C to +60°C for EVA hose and from -25°C to +60°C for EVA IVH hose (operating vacuum dependent on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong and flexible, classic rubber hose designed for compressed air (also oiled), water, and non-aggressive chemical liquids in industry and agriculture. Outer layer resistant to abrasion, aging, ozone, and weather conditions. Inner layer: black synthetic rubber. Reinforcement: synthetic braid. Outer layer: black synthetic rubber. Working pressure: 20 bar. Operating temperature: from -25°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible suction and discharge hose intended for the transport of food, pharmaceutical, and cosmetic substances: water, fruit juices, beer, wine, vinegar, alcohols up to 96% concentration, milk and its derivatives, creams, soaps, aromatic substances, pigments, and others. Resistant to fats and oils within standard usage range. Good chemical resistance to light chemicals – solutions of acids and bases. Extruded, completely smooth inner and outer surface of the hose facilitates flow and cleaning. Double reinforcement of the hose with a spiral and braid ensures good strength against overpressure and vacuum. The hose material is non-vulcanized, clean (contains no vulcanization additives), resistant to hydrolysis, does not promote bacterial growth, has low porosity and low permeability. Completely neutral in taste and odor, does not alter the organoleptic properties of the medium. Resistant to aging, weather conditions, and UV radiation. Hose cleaning, disinfection, or sterilization must be carried out strictly according to the recommendations provided in the catalog sheet below. Washing by SIP method is not recommended as it shortens the hose's service life. Application for high-proof alcohol (its vapors or other flammable substances) requires consideration of hazards related to static electricity. Norms and requirements: 1) Food industry, contact with food: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulation fluids A, B, C, D1, D2), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 “e”. 2) Pharmaceutical industry: USP CLASS VI. Hose material: transparent TPE-S. Reinforcement: polyester braid, AISI 302 steel spiral. Working pressure: from 7 bar to 17 bar, depending on the hose diameter. Operating temperature: -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight, flexible hose designed for the transport of air, vapors, dust, fine particles, powders, grains, and lightweight bulk materials. Intended for use in the food and pharmaceutical industries. Highly flexible and very compressible axially, also elastic at low temperatures. Good abrasion resistance, resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. Installation on couplings with bridge clamps (right-handed). Other diameters may be available upon special request. The hose is available in the following versions: P2 PU FOOD – steel wire (copper-plated) spiral; P2 PU PAS FOOD – stainless steel wire spiral, hose material permanently antistatic (R ≤ 108 Ω, according to TRGS 727). P2 PU FOOD and P2 PU PAS FOOD hoses comply with European regulations 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP), and American FDA 21 CFR 177.2600 and 178.2010. Suitable for temporary contact with food during the transfer of dry, bulk, non-fatty food substances - under the conditions specified in the manufacturer's declaration of conformity (available from Tubes International). Hose material: transparent polyether-polyurethane. Wall thickness measured between the spiral: 0.4 mm. Reinforcement: steel wire spiral (P2 PU FOOD), stainless steel wire AISI 301 spiral (P2 PU PAS FOOD). Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMultifunctional PVC hose, soft, flexible, and elastic. Designed for water, air, and light chemicals. Often used for color differentiation of individual installation lines. Available in black upon special request. Can be used (at temperatures up to 40°C) for liquid and semi-liquid food products such as juices, beverages, beer, wine, alcohols with a concentration of up to 50%, milk, and its derivatives. Not recommended for oils and fatty food substances. The TCN COLOR hose complies with European requirements 1935/2004/EC, 10/2011/EU (simulants A, B, C, and D1), 2023/2006/EC (GMP). Suitable for temporary contact with food during the transfer of food substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International). Inner layer: transparent PVC. Reinforcement: polyester braid. Outer layer: red (R) or blue (BL) PVC. Working pressure at 20°C: from 16 bar to 22 bar - depending on the hose diameter. As the operating temperature increases, the working pressure value of the hose decreases. Operating temperature: from -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, abrasion-resistant pressure hose designed for the transmission of drinking water in large quantities under high working pressure. Flat in a resting state, which facilitates handling and storage. With minimal elongation under pressure and no tendency to kink or twist. Reinforced with a circumferentially woven polyester braid, completely bonded and surrounded by thermoplastic polyurethane in the original hot extrusion production process through braiding. Meets requirements for the transmission of cold drinking water: PZH (no. B.BK.60110.0171.2022, valid until 01.04.2025), KTW-DVGW, WRAS(BS6920), and NSF61. Intended for permanent, temporary, and emergency drinking water supply installations. Used for delivering water to ships, in military field installations, humanitarian actions, mass event services, festivals, etc. Available in other diameters up to 305 mm upon special request. Maximum working pressure for temporary use established according to a safety factor of 2:1 approved by the manufacturer (only for water and safe, non-flammable liquids). To maximize lifespan, it is not recommended to exceed 1/3 of the bursting pressure and the specified breaking force. Standard roll length: 200 m. Hose material: blue polyurethane - polyether (PU) embedded in the braid (textile spacer) in the hose extrusion process. Working pressure: from 18 bar to 25 bar - depending on the hose diameter and temperature. Operating temperature: from -50°C to +75°C (for clean water).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible suction and discharge hose intended for water, juices, beverages, and other food products. The absence of phthalates in the material allows the hose to be used for the transfer of milk and its derivatives, as well as alcohols with a concentration of up to 50% and temperatures up to +60°C. Not recommended for oils and fatty food substances. Reinforcement with a hard PVC spiral, resistant to impacts, ensures good resistance to vacuum and hose collapse. The transparent wall allows for easy visual monitoring of flow. The smooth inner surface reduces flow losses and ensures ease of cleaning. The outer surface of the hose is also smooth, facilitating the installation of fittings using tapes or clamps, reducing external damage from abrasion, and making it easier to keep the hose clean. In applications not involving direct contact with food (in industry, construction, agriculture), it can be used for light chemicals, water, sludges, and wastewater, other liquids (without fats, oils, and hydrocarbons), as well as for air, vacuum transfer of dust, powders, granules, and other lightly abrasive bulk substances (non-fatty). Abrasiveness and potential static electricity issues should be considered. As a hose reinforced only with a hard PVC spiral, lacking a braid, it exhibits some elongation under pressure, which should be taken into account in applications, especially at temperatures above +40°C. Standards and requirements: Food industry, contact with food: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B, C, and D1), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: hardened PVC spiral. Working pressure: from 3 bar to 7 bar, depending on the hose diameter. Operating temperature: -15°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsExternally corrugated flexible and strong suction and discharge hose for water and sewage. It is characterized by good resistance to external damage and harsh operating conditions, as well as resistance to UV radiation and low temperatures. Used in irrigation systems, tankers, for flushing sewers, and emptying septic tanks. Also used in industrial installations. Hose material: gray-purple PVC. Reinforcement: hard PVC spiral. Working pressure: from 3 bar to 8 bar, depending on the hose diameter and temperature. Operating temperature: from -20°C to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, soft, and flexible, easy to operate food-grade suction hose designed for the transfer of food substances requiring the use of odorless and tasteless rubber. Free from phthalates and bisphenol A. Suitable for milk and its derivatives, as well as wine, beer, and fruit juices. Not recommended for oils and fatty food substances. The outer layer of the hose is resistant to abrasion and weather conditions. Standards and requirements: Food industry, food contact 1935/2004/EC and 2023/2006/EC (GMP), D.M. 21/03/73, FDA 21 CFR 177.2600, BfR XXI cat. 2. Inner layer: white natural rubber (NR). Reinforcement: synthetic cord. Outer layer: blue EPDM rubber. Working pressure: 6 bar. Operating temperature: from -25°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible, and pliable suction hose resistant to temperature, designed for the discharge of gases, vapors, smoke, and high-temperature air. Flame-retardant, resistant to hot sparks within a certain range. Mainly used in the metallurgical, foundry, ceramic, and glass industries, around furnaces, engines, and as thermal insulation. Characterized by high compressibility - up to 1:6, strong construction due to glass fabric reinforced with stainless steel threads, and impact resistance thanks to the external spiral. Used exclusively as a suction hose operating under vacuum, due to the possibility of gas permeation when under pressure (degassing). Also available with a stainless steel spiral (from a diameter of 80 mm). Hose installation on couplings with left-handed bridge clamps. Standard length: from 2 to 10 m - contact Tubes International. Hose material: impregnated glass fabric with stainless steel fibers, externally gray. Reinforcement: external spiral made of wire and galvanized steel sheet. Operating temperature: from -50°C to +400°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight and flexible suction and discharge hose, intended for general industrial applications (in industry, construction, agriculture). It can be used for water, light chemicals, sludges and wastewater, plant protection products, other liquids (excluding fats, oils, and hydrocarbons) as well as for air, vacuum transfer of dust, powders, granules, and other lightly abrasive bulk materials (non-greasy). Abrasiveness and potential static electricity issues should be considered. In the food industry, it can be used for the transfer of hydrated food, acidic substances, and alcohols up to 20%, e.g., juices, beverages, beer, wine (simulants A, B, C; up to +60°C and 2 hours). Not recommended for milk and its derivatives, as well as oils and fatty food substances. Reinforced with a hard PVC spiral, resistant to impact, ensures good vacuum resistance and prevents hose collapse. The smooth inner surface reduces flow losses and ensures ease of cleaning. The outer surface is slightly corrugated, smooth for small diameters. The FLORIDA hose complies with European requirements 1978/142/EEC, 1935/2004/EC, 1895/2005/EC, and 10/2011/EU (simulants A, B, C), 2023/2006/EC (GMP). Suitable for temporary contact with food during the transfer of food substances - under the conditions specified in the manufacturer's declaration of conformity (available from Tubes International). Hose material: transparent PVC. Reinforcement: hard PVC spiral (gray). Working pressure for a temperature of 20°C: from 3 bar to 6.5 bar - depending on the hose diameter. As the operating temperature increases, the working pressure value of the hose decreases. Operating temperature: from -5°C to +60°C.
